Backguard Installation

ManualsBrandsHestan ManualsCookingKRT364GDLP Hestan 36" KRT Series Gas Rangetop with 4 Burners and Griddle - Liquid Propane - Steeletto Stainless Steel

BACKGUARD

INSTALLATION

INSTRUCTIONS

KBGIT / KBGLB / KBGHS

IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN

THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN.

THE APPLIANCE MUST BE COMPLETELY COOL AND THE GAS SOURCE MUST BE SHUT OFF. THE

UNIT MUST BE UNPLUGGED FROM THE POWER OUTLET, OR THE ELECTRICAL BREAKER SHUT

OFF. YOU WILL NEED TO MOVE THE APPLIANCE AWAY FROM THE WALL FOR ACCESS.

SOME PARTS INSIDE YOUR APPLIANCE HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN

HANDLING THE VARIOUS COMPONENTS TO AVOID PERSONAL INJURY. WEAR GLOVES WHEN

HANDLING.

TOOLS REQUIRED:

Work gloves

Safety glasses

Phillips screwdriver

5/16” & 3/8” deep socket wrench or nut driver

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Flammable Gas - disconnect all propane or natural gas supplies to this

unit before servicing.

Electrical Parts & Components – disconnect all power supplies before

servicing.

1. Your Hestan appliance was shipped with an Island Trim Backguard (KBGIT) from the factory. From

the rear of the unit, remove screw (Item A), then remove the rear cover, then remove remaining

screws (Item C).

REMOVAL OF EXISTING BACKGUARD

COVER

Summary of content (8 pages)

PAGE 1
BACKGUARD INSTALLATION INSTRUCTIONS EN KBGIT / KBGLB / KBGHS IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. THE APPLIANCE MUST BE COMPLETELY COOL AND THE GAS SOURCE MUST BE SHUT OFF. THE UNIT MUST BE UNPLUGGED FROM THE POWER OUTLET, OR THE ELECTRICAL BREAKER SHUT OFF. YOU WILL NEED TO MOVE THE APPLIANCE AWAY FROM THE WALL FOR ACCESS. SOME PARTS INSIDE YOUR APPLIANCE HAVE SHARP EDGES.
PAGE 2
REMOVAL OF EXISTING BACKGUARD (CONTINUED) 2. From both sides of the unit, remove screws (Item A), then pull the backguard up and toward the rear of the appliance. EN EXISTING BACKGUARD A INSTALLATION OF NEW BACKGUARD 3. Install the new backguard, then install the two kinds of screws as shown (Item A & C).
PAGE 3
INSTALLATION OF NEW BACKGUARD (CONTINUED) 4. If your backguard features a shelf, install the shelf and support using screws Item B. EN SHELF SUPPORT B HIGH SHELF MODEL ONLY 5. With all internal screws tightened, install the rear cover and secure with screws (Item A). The appliance may now be reconnected to the gas and electricity and returned to its position in your kitchen.
PAGE 5
INSTRUCTIONS D’INSTALLATION DU DOSSERET KBGIT / KBGLB / KBGHS FR IMPORTANT - LISEZ TOUTES LES INSTRUCTIONS AVANT DE COMMENCER LES INSTRUCTIONS PRÉVUES DANS CE DOCUMENT DOIVENT ÊTRE EFFECTUÉES PAR UN TECHNICIEN QUALIFIÉ. L’APPAREIL DOIT ÊTRE COMPLÈTEMENT FRAIS ET LA SOURCE DE GAZ DOIT ÊTRE ÉTEINTE. L’UNITÉ DOIT ÊTRE DÉBRANCHÉE DE LA PRISE D’ALIMENTATION OU DU COUPE-CIRCUIT ÉLECTRIQUE. VOUS DEVEZ DÉPLACER L’APPAREIL DU MUR POUR L’ACCÈS.
PAGE 6
RETRAIT DU DOSSIER EXISTANT (SUITE) 2. Retirer les vis (Article A) des deux côtés de l’appareil, puis tirez le dosseret vers le haut et vers l’arrière de l’appareil. DOSSERET EXISTANT FR A INSTALLATION DU NOUVEAU DOSSERET 3. Installez le nouveau dosseret, installez les deux types de vis comme indiqué (Articles A-C).
PAGE 7
INSTALLATION DU NOUVEAU DOSSERET (SUITE) 4. Si votre dosseret comporte une étagère, installez l’étagère et le support à l’aide des vis Article B. ÉTAGÈRE FR SUPPORT B ÉTAGÈRE HAUTE SEULEMENT 5. Une fois toutes les vis internes serrées, installez le couverture arrière et fixez-le avec les vis (Article A). L’appareil peut maintenant être reconnecté au gaz et à l’électricité et retourné à sa position dans votre cuisine.
PAGE 8
RETAIN THIS MANUAL FOR FUTURE REFERENCE CONSERVEZ CE MANUEL POUR UNE RÉFÉRENCE FUTURE Hestan Commercial Corporation 3375 E.