QuickSpecs
Step 3 - Other P4000 SANs Options
Step 3 - Other P4000 SANs OptionsStep 3 - Other P4000 SANs Options
Step 3 - Other P4000 SANs Options
Description
DescriptionDescription
Description
Two 6' Highline (IEC-IEC) power cord ships standard per P4300/P4500 Node
NOTE:
NOTE:NOTE:
NOTE:
HP P4300/P4500 Storage Systems servers no longer ship standard with NEMA power cords (P/N 163719-002) that allow
connection to 110V US wall outlets in a home or office. HP P4000 Storage Systems are primarily connected to PDU's in data center
racks so they now ship standard with only a PDU power cord (416151-B21). If a user wishes to power a HP P4000 Storage Systems
using a 110V receptacle (NEMA-15), the NEMA power cord (AF556A) must be ordered separately.
If customers require a power cord, they can check the power cord matrix for the appropriate cord. Please see the UPS and PDU
cable matrix's on the Power Protection page under Power Cords that lists cable descriptions, requirements, and specifications for
UPS and PDU units at the new HP Power Cord Link @ HP.com. Use the following new link:
www.hp.com/products/powercords
NOTE:
NOTE:NOTE:
NOTE:
Rack models ship standard with IEC cables.
Step 4 - Choose Supported Options For iSCSI Infrastructure
Step 4 - Choose Supported Options For iSCSI InfrastructureStep 4 - Choose Supported Options For iSCSI Infrastructure
Step 4 - Choose Supported Options For iSCSI Infrastructure
Select each required option with quantities specified. The P4000 G2 SANs support servers with industry standard Gigabit and 10
Gigabit (SFP+) Ethernet components from various manufacturers that conform to IEEE 802.3ab (1000base-T) standards.
Description with Parts Shipped:
Description with Parts Shipped:Description with Parts Shipped:
Description with Parts Shipped:
For details on standard Gigabit Ethernet components (including Gigabit Ethernet switches, Network Interface cards and Ethernet
cables) from HP
http://welcome.hp.com/country/us/en/prodserv/networking.html
Step 5 - Choose Rack Options
Step 5 - Choose Rack OptionsStep 5 - Choose Rack Options
Step 5 - Choose Rack Options
Select each required option with quantities specified.
Rack Airflow
Rack AirflowRack Airflow
Rack Airflow
Requirements
RequirementsRequirements
Requirements
Rack 10000 G2 series Cabinets
Rack 10000 G2 series CabinetsRack 10000 G2 series Cabinets
Rack 10000 G2 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling
efficiency for rack-mounted servers. The 10000 G2 Series Racks provide enhanced airflow for maximum
cooling, allowing these racks to be fully loaded with servers using the latest processors.
CAUTION:
CAUTION:CAUTION:
CAUTION:
If a third-party rack is used, observe the following additional requirements to ensure
adequate airflow and to prevent damage to the equipment: Front and rear doors: If your 42U server
rack includes closing front and rear doors, you must allow 830 square inches (5,350 sq cm) of hole
evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent
open area for ventilation). Side: The clearance between the installed rack component and the side
panels of the rack must be a minimum of 2.75 inches (7 cm).
CAUTION:
CAUTION:CAUTION:
CAUTION:
Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This
arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling
that can lead to thermal damage.
Rack Kit
Rack KitRack Kit
Rack Kit
HP P4000 G2 rack models have fixed rails which provide support for racks with round mounting holes
and tool-free support for racks with square mounting holes (including Compaq/HP 7000, 9000, 10000
and HP series), with an adjustment range of 26" - 36".
Telco Rack Support
Telco Rack SupportTelco Rack Support
Telco Rack Support
QuickSpecs
HP P4000 G2 LeftHand SAN Solutions
HP P4000 G2 LeftHand SAN SolutionsHP P4000 G2 LeftHand SAN Solutions
HP P4000 G2 LeftHand SAN Solutions
Configuration Information
DA - 13552 Worldwide — Version 20 — April 13, 2012
Page 37