Specification Sheet

QuickSpecs
HPE ProLiant DL360 Gen10 Server
Configuration Information
Page 32
This section lists some of the steps required to configure a Factory Integrated Model.
To ensure valid configurations are ordered,
Hewlett Packard Enterprise recommends the use of an HPE approved configurator.
Contact your local sales representative for information on configurable product offerings and requirements.
• Factory Integrated Models must start with a CTO Server.
• FIO indicates that this option is only available as a factory installable option.
• All Factory Integrated Models will be populated with sufficient hard drive blanks based on number of drives ordered with
server.
• Some options may not be integrated at the factory. Contact your local sales representative for additional information
European Union (EU) eco-design regulations for server and storage products, known as Lot 9, go into effect on March 1st, 2020.
Among other requirements, for servers this directive establishes power thresholds for idle state, as well as efficiency and performance
in active state which vary among configurations. HPE ProLiant Gen10 servers are compliant with Lot 9 requirements.
For more information regarding HPE Lot 9 conformance, please visit:
https://www.hpe.com/us/en/about/environment/msds-specs-more/erp-lot9-servers.html
Step 1: Base Configuration
(choose one of the following configurable models)
Network Choice
(NC) Models
Network
Choice models do not include embedded LOM. To enable networking capability please select either a FlexibleLOM NIC or a
validated alternative
from the Core Options section.
CTO Server
HPE DL360 Gen10 4LFF NC
CTO Server
HPE DL360 Gen10 8SFF NC
CTO Server
HPE DL360 Gen10 Premium
10NVMe NC CTO Svr
SKU Number
P19765-B21
P19766-B21
P19767-B21
TAA SKU*
P19768-B21
P19769-B21
P19770-B21
Processor
Not included as standard
DIMM Slots
24-DIMM slots (12 can be used for NVDIMMs or 12 can be used for HPE Persistent Memory)
Storage Controller
Embedded SW RAID (S100i) with 14 SATA ports
Optional: Choice of HPE modular Smart Array and PCIe plug-in controller
PCIe
2 PCIe slots (1 x16 FH / 1 x8 LP)
Optional: 1 x16 FH or LP
2 PCIe slots (1 x16 FH / 1 x8
LP)
Drive Cage - included
4 LFF - SAS/SATA
8 SFF - SAS/SATA
Optional: up to 2 NVMe or 2
Dual uFF (4x M.2 cartridges)
10 NVMe - SAS/SATA/NVMe
Optional: 1 Dual uFF (2x M.2
cartridges)
Network Controller
Choice of HPE FlexibleLOM for primary NIC and stand up card for additional NICs.
Notes: No embedded networking
Fans
1 CPU – 5 Standard Fans
2 CPU – 7 Standard Fans
Optional: High Performance Fans
2 CPU – 7 High Performance
Fans
Management
HPE iLO with Intelligent Provisioning (standard)
Optional: iLO Advance and OneView
USB
Front: 1 USB 3.0 + iLO service port
Rear: 2 USB 3.0
Internal: 2 USB 3.0
Optional: 1 USB 2.0 (lose iLO serv. Port)
Front: 1 USB 3.0 + iLO service
port
Rear: 2 USB 3.0
Internal: 2 USB 3.0
Notes:
−
*HPE offers multiple Trade Agreement Act (TAA) compliant configurations to meet the needs of US Federal Government
customers. These products are either manufactured or substantially transformed in a designated country.
−
HPE Persistent Memory is only supported on 2
nd
generation Intel Xeon Scalable processor series (Platinum 8200, Gold
6200, Gold 5200, Silver 4215 and 4215R).
− SKUs P19767-B21 & P19770-B21 do not support the Xeon-Gold 6250L or Gold 6250 processors.