User's Manual

ManualsBrandsHewlett Packard ManualsComputers & AccessoriesAruba 330 Series Wireless Access Point

Table Of Contents

Aruba 330 Series Wireless Access Point

Regulatory Compliance and Safety Information Guide

0511874-01 | March 2016 1

Introduction

This document contains domestic and international regulatory compliance and safety information for 330 Series access points.

To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.

 Electrical and Environmental Specifications

 Regulatory Information

 Proper Disposal of Aruba Equipment

Electrical and Environmental Specifications

For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/

safety_addendum.

Electrical

 Ethernet:

 ENET0: 100/1000/2500 BaseT auto-sensing Ethernet RJ45 interface

 ENET1: 100/1000 Base-T auto-sensing Ethernet RJ45 interface

 IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T)

 Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum).

 Power:

 48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36B)

 Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC)

Environmental

 Operating:

 Temperature: 0°C to +50°C (+32°F to +122°F)

 Humidity: 5% to 93% non-condensing

 Storage and transport:

 Temperature: -40°C to +70°C (40°F to +158°F)

All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is

responsible for ensuring that grounding is available and meets applicable national and electrical codes.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer

que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.

If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an

output rated 48VDC, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in

the US and Canada.

Summary of content (4 pages)

PAGE 1
Aruba 330 Series Wireless Access Point Regulatory Compliance and Safety Information Guide Introduction This document contains domestic and international regulatory compliance and safety information for 330 Series access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.
PAGE 2
Regulatory Information The following regulatory model names apply to the 330 Series access points:  AP-334/IAP-334: APIN0334  AP-335/IAP-335: APIN0335 Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits.
PAGE 3
Déclaration d’Industrie Canada Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada.
PAGE 4
European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine.