User's Manual

ManualsBrandsHewlett Packard ManualsElectronicsHP 425 Wireless 802.11n (AM) AP

Contents

Preparing for installation ········································································································································································ 2

Safety recommendations ·········································································································································································· 2

Safety symbols····················································································································································································· 2

General safety recommendations················································································································································ 2

Determining the installation position ·················································································································································· 2

Accessories provided with the AP ························································································································································· 3

Installation preparation checklist ··························································································································································· 4

Installing the AP ························································································································································································· 5

Mounting the AP on a table ····································································································································································· 5

Mounting the AP on a wall ······································································································································································· 6

Mounting the AP to a T-rail ····································································································································································· 9

Mounting the AP on a ceiling ······························································································································································· 12

Connecting the power supply ······························································································································································· 13

Connecting the AP to a local power supply ·························································································································· 13

Connecting the AP to a PoE power supply ···························································································································· 14

Connecting the AP to the network ······················································································································································ 14

Appendix A Chassis views and technical specifications ··········································································································· 16

Chassis views ································································································································································································ 16

Weights and dimensions ······························································································································································· 17

Power consumption ········································································································································································ 17

Power specifications ·················································································································································································· 17

AC voltage range ·············································································································································································· 17

Power adapter specifications ······················································································································································ 17

Storage media and memory specifications ····································································································································· 18

Appendix B LEDs ······················································································································································································ 19

Summary of content (24 pages)

PAGE 1
Contents Preparing for installation ········································································································································································2 Safety recommendations ··········································································································································································2 Safety symbols·································································································
PAGE 2
Preparing for installation IMPORTANT: For regulatory identification purposes, the HP 425 is assigned a regulatory model number (RMN) BJNGA-FB0002. This regulatory number should not be confused with the marketing name HP 425, or product code JG653A, JG654A, JG655A, JG656A, JG687A, and JG688A. Safety recommendations WARNING!  This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge.
PAGE 3
WARNING! Please carefully select the installation position and make sure the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Determine the installation position by observing the following principles:  The product shall be installed at a location where the radiating antenna can be kept 40 cm (15.75 in) from nearby person in normal operation condition to meet regulatory RF exposure requirement.
PAGE 4
Hex-head bolt, washer, and nut Antennas, power adapter, and power cable are user-supplied. Installation preparation checklist Before you install an AP, verify the following items:  Connect the power cord and connect the AP to the network. Examine the LED status to make sure the AP can operate correctly. For more information about AP LEDs, see "Appendix A Chassis views and technical specifications Chassis views The HP 425 provides the following external ports:  Two 2.
PAGE 5
(7) 10/100/1000 Mbps copper Ethernet port (8) Local power port Table 1 HP 425 port description Port Standards and protocols Description 2.4G-1/2  IEEE802.11b  IEEE802.11g  IEEE802.11n The antenna ports are provided for 2.4 GHz single-RF antennas. 5G-1/2  IEEE802.11a  IEEE802.11n The antenna ports are provided for 5 GHz single-RF antennas. 48V DC N/A The local power port is used for +48 VDC power supply to the device. ETHERNET  IEEE802.3  IEEE802.3u  IEEE802.
PAGE 6
Power adapter specifications Item Description Input 100 VAC to 240 VAC Output +48V @ 0.
PAGE 7
 Appendix B LEDs."  Verify that cabling has been completed.  The HP 425 supports 802.3af-compliant PoE. To achieve the best performance, HP recommends that you use GE connection to the power device.  Record the MAC address and serial number of the AP (marked on the rear of the AP) for future use.  If part of the power line is routed outdoors, use a power strip with lightning protection (user supplied) to connect the power cord of the AP to the power line.
PAGE 8
Installing the AP Figure 2 Installation flowchart Start Check before installation Ceiling mounting Determine the installation position T-rail mounting Attach the T-rail holder to the T-rail Attach the wallmounting bracket to the T-rail holder Mount the AP on a ceiling Mount the AP to a wall Mount the AP on a table Mount the wallmounting bracket to the ceiling Install the wallmounting bracket Install the AP Connect the power supply Connect the AP to the network End The HP 425 can only be used in
PAGE 9
Figure 4 Mounting the AP on the table Mounting the AP on a wall IMPORTANT: Connect the AP to the network by using an Ethernet cable, and then install the AP to the wall-mounting bracket. To mount the AP on a wall, a wall-mounting bracket and wall anchor kit is required. Figure 5 Screw hole locations and sizes (in mm) 3 4 103.0 2 40.0 1 Ø 5.0 86.0 136.0 (1) Hook (2) Mounting hole (3) Clip (4) Mounting clip To mount the AP on a wall: 1.
PAGE 10
Figure 6 Drilling holes in the wall 40 mm 86 mm 2. Insert a wall anchor into each mounting hole, and tap the wall anchor with a rubber hammer until it is flush with the wall surface. Figure 7 Inserting a wall anchor 3. Align the holes in the wall-mounting bracket with the anchors and insert screws through the installation holes into the wall anchors. 4. Adjust the position of the wall-mounting bracket and tighten the screws.
PAGE 11
Figure 8 Installing the wall-mounting bracket 2 3 1 4 (1) Wall-mounting bracket (2) Hook (3) Clip (4) Screw 5. Connect the AP to the network by using an Ethernet cable. 6. Align the mounting keyhole on the rear of the AP over the hook on the wall-mounting bracket. See 錯誤! 找不到參照來源。. 7. Mount the AP on the hook on the wall-mounting bracket. See callout 1 in Figure 9. 8. Pull down the AP until it clicks into place. See callout 2 in Figure 9.
PAGE 12
Figure 9 Mounting the AP to the wall mounting bracket 1 2 Mounting the AP to a T-rail IMPORTANT: The width of the T-rail must be in the range of 16 mm to 28 mm (0.63 in to 1.10 in).
PAGE 13
Figure 10 Screw hole locations and sizes (in mm) 3 4 103.0 2 40.0 1 Ø 5.0 86.0 136.0 (1) Hook (2) Mounting hole (3) Clip (4) Mounting clip Figure 11 T-rail holder 1 2 3 4 5 8 6 7 (1) T-rail clip (2) M4 screw nut (3) Clip holder (4) T-rail holder (5) M3 screw nut (6) M4 × 5 screw (7) M3 × 8 screw (8) Mounting hook To mount the AP to a ceiling T-rail: 1. Loosen the two M3 × 8 screws on each clip holder. Do not remove the screws. 2.
PAGE 14
Figure 12 Attaching the T-rail holder to the T-rail 1 2 3. Tighten the four M3 × 8 screws on the two clip holders. 4. Verify that the T-rail holder is attached to the T-rail. 5. Hook the mounting clip (see callout 3 in Figure 13) of the wall-mounting bracket to the mounting hook (see callout 2 in Figure 13) of the T-rail holder. 6. Insert the two M4 × 5 screws (see callout 1 in Figure 13) through the two 5 mm (0.
PAGE 15
Mounting the AP on a ceiling CAUTION:  Verify that the AP is secured to the mounting bracket to avoid falloff.  Do not use this method to mount the AP to a location made of low-intensity materials such as a plaster ceiling. If this installation method is required in such an environment, put a high-intensity plate beneath the ceiling to secure the installation.  The ceiling tiles must be less than 18 mm (0.71 in) thick, and the ceiling can bear a weight of at least 5 kg (11.02 lb).
PAGE 16
Figure 15 Installing the mounting bracket to a ceiling 1 2 3 4 5 6 (1) Nut (2) Washer (3) Ceiling (4) Wall-mounting bracket (5) Hex-head bolt (6) Hook Connecting the power supply The HP 425 can be powered by using a local or PoE power supply. You can select either method as needed. Make sure the power supply for either method is well grounded before you power on the AP. Before connecting the local or PoE power supply, verify that the power supply is steady.
PAGE 17
Figure 16 HP 425 ports 1 2 3 4 5 6 7 8 (1) 2.4G antenna port 2 (2) 2.4G antenna port 1 (3) 5G antenna port 1 (4) 5G antenna port 2 (5) Reset button (6) Console port (7) 10/100/1000 Mbps copper Ethernet port (8) Local power port Table 3 HP 425 port description Port Standards and protocols Description 2.4G-1/2  IEEE802.11b  IEEE802.11g  IEEE802.11n The antenna ports are provided for 2.4 GHz single-RF antennas. 5G-1/2  IEEE802.11a  IEEE802.
PAGE 18
Item Description Height 51 mm (2.01 in) Width 188.6 mm (7.43 in) Depth 188.6 mm (7.43 in) Weight 640.5 g (22.59 oz) Power consumption Model Maximum power consumption HP 425 12.95 W Power specifications AC voltage range Table 4 AC voltage range Power supply mode Voltage range Frequency Single-phase three-wire (V) 100 V to 240 V 50 or 60 Hz Power adapter specifications Item Description Input 100 VAC to 240 VAC Output +48V @ 0.
PAGE 19
Appendix B LEDs." Connecting the AP to a local power supply The AP is not shipped with a power adapter or power cable. The HP 425 supports both listed AC and DC power adapters marked“LPS”or limited power source. You can connect the power port of the AP to the power source through a power adapter to supply power to the AP.
PAGE 20
Figure 18 PoE connection 1 3 2 (1) Ethernet port (2) Ethernet cable (3) PoE switch Connecting the AP to the network APs can access the Internet or metropolitan area network (MAN) through the Ethernet uplink interface. To implement Internet or MAN access, connect the Ethernet port of the AP to an Ethernet port of an Ethernet switch. When the AP operates as a fit AP, all of its settings are configured on the AC. You can use the display wlan ap all command to examine the AP status on the AC.
PAGE 21
Appendix A Chassis views and technical specifications Chassis views The HP 425 provides the following external ports:  Two 2.4 GHz antenna ports, two 5 GHz antenna ports  A console port  A 10/100/1000 Mbps copper Ethernet port  A power supply port NOTE: The HP 425 also provides a reset button. Figure 19 HP 425 ports 1 2 3 4 5 6 7 8 (1) 2.4G antenna port 2 (2) 2.
PAGE 22
Port Standards and protocols Description 2.4G-1/2  IEEE802.11b  IEEE802.11g  IEEE802.11n The antenna ports are provided for 2.4 GHz single-RF antennas. 5G-1/2  IEEE802.11a  IEEE802.11n The antenna ports are provided for 5 GHz single-RF antennas. 48V DC N/A The local power port is used for +48 VDC power supply to the device. ETHERNET  IEEE802.3  IEEE802.3u  IEEE802.3af 10/100/1000 Mbps copper Ethernet port .
PAGE 23
Item Description Input 100 VAC to 240 VAC Output +48V @ 0.
PAGE 24
Appendix B LEDs Table 7 LED description Mark Color Status Description The AP is booting. NOTE: Flashing at 1 Hz Green When the AP operates as a fit AP, it is always in this state before it is registered to an AC. Breathing A client is connected to the 2.4G port. Flashing at 0.25 Hz The AP has been booted and has registered to the AC. It is in standby state (no client is connected to the AP). Flashing at 2 Hz The AP is updating its system software image.