User's Manual

ManualsBrandsHewlett Packard ManualsElectronicsMSM317 Access Device

Table Of Contents

MSM317 Access Device Installation Guide

This guide describes how to physically install the MSM317 in an electrical outlet box

and make all necessary power and network connections. This guide assumes that

before installing the MSM317, all configuration issues have been addressed as

described in the MSM317 Access Device Installation and Getting Started Guide

available at: www.procurve.com/customercare/support/manuals/index.htm.

Package contents

Professional installation required

Professional installation of the MSM317 is required for proper RF operation and compliance.

Please consult with a professional installer who is trained in RF installation and knowledgeable

about local regulations (including building and wiring codes) to ensure that the MSM317 is

operating in accordance with channel, power, indoor/outdoor restrictions and license

requirements for the intended country of operation.

Safety information

Take note of the following safety information during installation of the MSM317:

• If your network covers an area served by more than one power distribution system, be sure

all safety grounds are securely interconnected.

• Network cables may occasionally be subject to hazardous transient voltages (caused by

lightning or disturbances in the electrical power grid).

• Handle exposed metal components of the network with caution.

• This product does not have a power switch. It is powered-on when the Uplink port is plugged

into a PoE power source.

• MSM317 body

• Two faceplates (NEMA-WD6 and BS 4662)

• Two trim panels (NEMA-WD6 and BS 4662)

• Two mounting screws

•This guide

The MSM317 Access Device is a

wireless/wired end-point solution with

an integrated four-port (plus uplink)

managed Ethernet switch that can be

installed in a standard NEMA-WD6

(US) or BS 4662 (International)

electrical outlet box.

It provides a complete connectivity

solution for hospitality or multiple

dwelling unit applications, supporting

a variety of IP-based in-room

applications over a single wire.

NEMA-WD6 Version

(J9422A)

BS 4662 Version

(J9423A)

Summary of content (5 pages)

PAGE 1
MSM317 Access Device Installation Guide This guide describes how to physically install the MSM317 in an electrical outlet box and make all necessary power and network connections. This guide assumes that before installing the MSM317, all configuration issues have been addressed as described in the MSM317 Access Device Installation and Getting Started Guide available at: www.procurve.com/customercare/support/manuals/index.htm.
PAGE 2
MSM317 Access Device Installation Guide 2 • This product and all interconnected equipment must be installed indoors within the same building, including all associated network connections as described by Environment A of the IEEE 802.3af standard. • It is normal for the rear metal cover of the MSM317 to get hot during operation. The cover is a heat sink and is used to dissipate the heat generated by the MSM317.
PAGE 3
MSM317 Access Device Installation Guide 3 Installation procedure A. Attach the faceplate Place the appropriate faceplate (NEMA-WD6 for US or BS 4662 for international) over the front of the MSM317 body and press firmly to snap it into place. B. Prepare the electrical outlet box The MSM317 requires a single-gang electrical outlet box mounted in a wall cavity. The US version requires a box conforming to NEMA-WD6, with a minimum depth of 1.4 inches.
PAGE 4
MSM317 Access Device Installation Guide 4 Faceplate and trim panel removal To remove the faceplate, slightly push in two tabs on one side of the MSM317 body with a small screwdriver. To remove the trim panel, pry off the trim panel with a small flat screwdriver. (BS 4662 version shown.) Press here to remove the faceplate. Use a screwdriver to pry off trim panel here. Punch-down block wiring When terminating a cable run with the Punch-down block, always use solid conductor cables.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.