User's Manual

ManualsBrandsHewlett Packard ManualsElectronics802.11a/b/g/n Access Point

The E-MSM430, E-MSM460, and E-MSM466 are Wi-Fi Alliance

authorized Wi-Fi CERTIFIED 802.11n/a/b/g products. The Wi-Fi

CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.

E-MSM430, E-MSM460, and E-MSM466 802.11n Access Points Quickstart

This Quickstart shows you how to install and get started using the E-MSM430, E-MSM460, and E-MSM466 Dual Radio 802.11n Access Points, hereafter referred

to as the AP except for where specific model references are made. (See Products list on page 8 for part numbers.)

Please visit www.hp.com/networking/support for the latest documentation including the MSM3xx / MSM4xx Access Points Management and Configuration Guide

and the MSM7xx Controllers Management and Configuration Guide.

Hardware overview

➀

➁

➅

➇

➈

➆

➃

➄

➃

➂

Front view

1: Status Lights (Left to right) Power, Ethernet, Radio1, Radio 2

2: Cable lock hole

3: Retention screw hole

Back view

4: Antenna connectors (E-MSM466 only), 

Radio 1 right, Radio 2 left

5: Reset button

6: Cable channel

7: AP Bracket tab slot

8: Console port

9: Ethernet port

E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 1 Friday, October 15, 2010 12:49 PM

Summary of content (8 pages)

PAGE 1
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 1 Friday, October 15, 2010 12:49 PM The E-MSM430, E-MSM460, and E-MSM466 are Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11n/a/b/g products. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. In E-MSM430, E-MSM460, and E-MSM466 802.11n Access Points Quickstart This Quickstart shows you how to install and get started using the E-MSM430, E-MSM460, and E-MSM466 Dual Radio 802.
PAGE 2
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 2 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart Package contents The AP, AP Bracket, Padlock Bracket, two sets of AP Bracket T-bar clips with screws, two mounting screws with wall anchors, retention screw (4-40x1/4”), Adapter Bracket, and documentation. Ports • Ethernet port: Auto-sensing 10/100/1000 BaseT Ethernet port with RJ-45 connector. The port supports Power over Ethernet (PoE) 802.3af.
PAGE 3
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 3 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart 3 Installation If the AP will be powered by a user-supplied PoE power injector, use only a gigabit-compatible power injector. Although 10/100 PoE-enabled switches are compatible, PoE injectors designed for 10/100 networks only are NOT compatible with the AP. 3.
PAGE 4
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 4 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart 1. Slide one of the T-bar clips into the AP Bracket T-bar slot. Screw it into 2. 3. 4. 5. place using two of the four provided self-tapping screws. Select the screw holes marked according to the width of your T-bar, one of 9/16”, 15/16”, or 1.5”.
PAGE 5
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 5 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart Connect the antennas (E-MSM466 only) Connect the antenna cables to the E-MSM466, respecting the color-coding and radio designation. Removing the AP To remove the AP from the bracket: 1. Detach any locks and remove the retaining screw. 2.
PAGE 6
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 6 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart After the discovery process is complete, and the AP has established a secure management tunnel to a controller, the Power light remains on and the Ethernet and Radio lights blink to indicate the presence of traffic. Status light behavior in autonomous mode Light State The AP has no power. Blinking The AP is starting up.
PAGE 7
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 7 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart D. Log in 1. Wait until the Power light stops blinking and remains on. 2. On the Login page, specify admin for both Username and Password and then select Login. 3. Click through the other prompts for License and Registration. 4. In some regions, a Country prompt appears. Select the country in which the AP will operate.
PAGE 8
E-MSM430-460-466-QS-Nov10-5998-0615-v55.fm Page 8 Friday, October 15, 2010 12:49 PM HP E-MSM430, E-MSM460, E-MSM466 Dual Radio 802.11n Access Points Quickstart 8 Products list H. Before performing additional configuration Other regulatory information Configure your computer LAN port and connect it to the same network as the AP. Re-launch the AP management tool at https:// where is the AP IP address from Section F above.