User Manual

ManualsBrandsHewlett Packard ManualsElectronicsWLAN 802.11a/n/ac mini-PCIe Module

The HP 560 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED

802.11ac product. The Wi-Fi CERTIFIED Logo is a certification

mark of the Wi-Fi Alliance.

HP 560 Wireless 802.11ac Access Point Quickstart

This Quickstart shows you how to install and get started using the HP 560 Dual Radio 802.11ac Access Point, hereafter referred to as the AP. The latest HP

documentation is available at www.hp.com/support/manuals.

Important: Operating this AP in requires these minimum software versions: HP MSM7xx,V5.5.2; HP 20G Unified Wired-WLAN Module in an HP 7500,

CMW520-R6708 or in an HP 10500 CMW520-R1208; HP 830, CMW520-B3308P18; HP WX5002/4, CMW520-R2308P18-EI.

Hardware overview

➀

➁

➅

➇➈

➆

➃

➄

➃

➂

Front view

1: Status LEDs (left to right) Power/System OK, Ethernet, Radio 1, Radio 2

2: Cable lock hole

3: Retention screw hole

Back view

1: Reset button

2: Cable channel

3: AP Bracket tab slot

4: Console port

5: Ethernet port

Model Numbers

HP 560:

J9846A (WW), J9845A (AM), J9847A (JP), J9848A (IL)

Summary of content (8 pages)

PAGE 1
The HP 560 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11ac product. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. In HP 560 Wireless 802.11ac Access Point Quickstart This Quickstart shows you how to install and get started using the HP 560 Dual Radio 802.11ac Access Point, hereafter referred to as the AP. The latest HP documentation is available at www.hp.com/support/manuals. Important: Operating this AP in requires these minimum software versions: HP MSM7xx,V5.5.
PAGE 2
HP 560 Wireless 802.11ac Access Point Quickstart Package contents The AP, AP Bracket, Padlock Bracket, two sets of AP Bracket T-bar clips with screws, two mounting screws with wall anchors, retention screw (4-40x1/4”), Adapter Bracket, and documentation. Ports • Ethernet port: Auto-sensing 10/100/1000 BaseT Ethernet port with RJ-45 connector. The port supports PoE (Power over Ethernet) 802.3af and 802.3at. • Console port: Standard console (serial) port with RJ-45 connector.
PAGE 3
HP 560 Wireless 802.11ac Access Point Quickstart 3 Installation The AP can be mounted on a wall, a wall-mounted electrical box, or a suspended ceiling. The AP Bracket is mounted first and then the AP is attached to the bracket. The AP Bracket is two-sided: The AP is installed on the side with the UP arrow. The other side with the T-bar clip screw holes faces the wall or T-bar. ➁ ➀ ➃ ➄ ➂ ➀ ➃ ➄ ➄ ➃ ➀ ➆ ➂ ➇ ➇ ➄ ➇ Attach the AP on page 4. Mounting on an electrical box 1.
PAGE 4
HP 560 Wireless 802.11ac Access Point Quickstart 2. 3. 4. 5. Warning: Areas above false ceilings can contain dangerous electrical cabling, gas pipes, and other hazards. Make whatever safety arrangements are needed to ensure that you can work safely above the false ceiling. HP recommends that you use a non-conductive step ladder such as one made of fiberglass. Position yourself at shoulder-height above the ceiling so that you can attach the second T-bar clip.
PAGE 5
HP 560 Wireless 802.11ac Access Point Quickstart Removing the AP 5 Installation AP status LED states (with controller connection) To remove the AP from the bracket: 1. Detach any locks and remove the retaining screw. 2. While carefully holding the AP, insert a flat screwdriver into the cable channel between the channel wall and the AP Bracket latch, releasing the AP from the bracket, while being careful to retain grip on the AP as you slide it away from the AP Bracket lock tab. 3.
PAGE 6
HP 560 Wireless 802.11ac Access Point Quickstart 6 Using autonomous mode of 255.255.255.0. Set the default gateway to 192.168.1.1, and DNS server to 192.168.1.1. In autonomous mode, the AP operates as a standalone AP. You configure and manage an autonomous AP by using its web-based management tool, as described in this section. AP status LED states in autonomous mode LED State Off Power/ System OK Ethernet Radio Blinking Using autonomous mode Description The AP has no power.
PAGE 7
HP 560 Wireless 802.11ac Access Point Quickstart 7 4. If a Country prompt appears, select the country in which the AP will Using autonomous mode • Assign a static IP address to the AP. The address must be on the same operate. subnet as the network to which the AP connects. Caution: To ensure compliance, you must select the correct 1. Select Network > DNS, and set the DNS server address. Select Save. 2. Select Network > Ports > Bridge port. 3. Select Static, and then Configure.
PAGE 8
HP 560 Wireless 802.11ac Access Point Quickstart 8 Using autonomous mode © Copyright 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.