Aruba Networks MSR4000 Installation Guide 0510871-01
Copyright 2005-2011 by Aruba Networks, USA. All rights reserved. Statement of Conditions In the interest of improving internal design, operation function, and/or reliability, Aruba Networks reserves the right to make changes to products described in this document without notice. Aruba Networks does not assume any liability that may occur due to the use or application of the product(s) described herein.
merchandisability, the warranty of fitness for a particular purpose, and any warranty of noninfringement of the intellectual property rights of any third party. Liability of the company for loss is limited to the total amount paid to the company by the customer during the previous calendar year.
Make sure not to connect or disconnect cables during periods of lightning activity. A surge protective device should be installed to prevent potential damage from very high surges, for instance, the peak surges caused by lightning. Explosive Device Proximity Warning Do not operate wireless network devices close to explosive merchandise or in explosive environments if devices are not certified for operation in such an environment, for example, in the vicinity of a gas station.
The installation of the power switch must be performed by a trained professional technician. The power switch is not supplied with the MSR4000. The power cord must be assembled by a professional installer, and the final assembly must comply with related requirements. Solar Irradiation and High Temperature Protection Pay attention to level of sunlight, which can increase the working temperature of MSR4000 to higher than specifications allow.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. REMINDER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
MSR4000 Installation Guide 6
Table of Contents 1 PRODUCT OVERVIEW ............................................................................................................................................ 8 1.1 1.2 INTERFACES..................................................................................................................................................... 8 LED STATUS INDICATORS ...............................................................................................................................
1 Product Overview 1.1 Interfaces The MSR4000 family will include two models supporting POE, AC/DC power supply respectively. Currently the model supporting POE is available as MSR4K43N0. Note In this guide, for general instruction that apply to all models, ‘MSR4000’ will be used; otherwise, ‘MSR4K43N0’ will be used. Figure 1-1 Interfaces on MSR4K43N0 1.
The table below lists the meanings of the LEDs on the MSR4000.
2 Installation Preparations This chapter describes the preparations for MSR4000 installation, including preparation of installation tools,selection of installation sites and etc. 2.1 Preparing Installation Tools When installing MSR4000, you may need the following tools. You shall select the tools according to the actual situation.
3 MSR4000 Installation The installation flowchart of MSR4K43N0: MSR4000 Installation Guide 11
3.1 Installing MSR4000 on a pole The mounting bracket assembly for installing MSR4000 concludes: solar shield, a pair of pole anchors, a mounting bracket and bolts. MSR4000 can be mounted on a pole or wall. (Pole diameter must be 40 to 60 mm at the position where the MSR4000 will be mounted.) Note If using M8 x150 long bolts (not provided in the box shipped with MSR4000), the MSR4000 can be mounted on a pole with 96mm diameter.
Figure 3-2 Positions of screw holes on the solar shield Step 2 Screw the two M4 x16 bolts into the holes on the back of the MSR4000. (See figure below) Figure 3-3 Positions of screw holes on the back of the MSR4000 Step 3 Fix the mounting bracket and the pair of pole anchors on the pole using four M8 x110 bolts (with flat washers, spring washers and nuts).
Figure 3-4 the pole anchors and mounting bracket 1 A mounting bracket 2 A pair of pole anchors Figure 3-5 Fix the mounting bracket and the pair of pole anchors on the mounting bracket Step 4 Align the two M4 x16 bolts on the back of MSR4000 with the holes on the mounting bracket and hang the MSR4000 on the bracket.
Figure 3-6 Fix the MSR4000 on the bracket 1 Hang the two M4 x16 bolts of the back of the MSR4000 on the two holes of the mounting bracket. Step 5 Align the two installation holes on the side of the MSR4000 with the corresponding holes on the mounting bracket and then use the two M6 x30 bolts (with flat and spring washers) to fix them.
3.2 Installing MSR4000 on a wall Step 1 Mark 1) Put the mounting bracket on the installation position against the wall. 2) Mark four expansion screw holes on the wall. Figure 3-8 Positions of screw holes Step 2 Drill holes 1) Use a percussion drill to drill four holes on the four markings. (Expansion screw size: M8 x 100mm) Step 3 Install masonry anchors 1) Insert a masonry anchor into each drilled hole vertically.
Figure 3-9 Positions of the two M4 x16 bolts and the holes 1 Hang the two M4 x16 bolts of the back of the MSR4000 on the two holes of the mounting bracket. Step 6 Fix MSR4000 1) Align the two installation holes in the MSR4000 with the corresponding holes in the wall-mounting bracket. 2) Insert the two M6 x30 bolts (with flat and spring washers) through the installation holes, and tighten the bolts.
3.3 Grounding the MSR4000 The grounding must be completed before powering up the MSR4000.The residence of grounding wire should be less than 5 ohm and the grounding cable’s cross-section area should be no less than 6 mm2.The grounding hole is at the left side of the MSR4000. Figure 3-11 Grounding the MSR4000 Step 1 Peel the cover of one end of the grounding cable (green or yellow and green grounding cable) and place the bare grounding cable into the copper lug, and press firmly with the crimping pliers.
Figure 3-12 Connecting the RF cable 1 RF cable 3 Grounding cable for lightning arrester 2 lightning arrester 4 Antenna interface Step 1 Screw one end of the lightning arrester onto the antenna interface. Step 2 Connect the RF cable to the other end of the lightning arrester. Step 3 Water-proof the antenna connection with PVC insulation tape, adhesive insulation tape and strap. 3.
Figure 3-14 Weatherproof Connector Kit 1 Shielded RJ45 connector 4 Locknut 2 Gasket mat 5 Seal ring 3 Waterproof connector socket 6 Sealing nut Note Failure to use the included weatherproof connector kit can lead to connectivity and PoE issues. Installation Steps 1. Remove the cover from the adhesive side of the gasket mat and place it over the weatherproof connector socket. 2. Place the locknut over the weatherproof connector socket. 3.
4 Note To log onto the MSR4000 via Console port, use the setting as shown in table below: Baud Rate 115200 Data Bits 8 Parity None Stop Bits 1 Flow Control None Default Username and Password root : public MSR4000 Installation Guide 21
