Users Manual

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired
operation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Target Corp. Mpls. MN, 55403 Phone: [phone]
FCC ID: 2AO23-QIC38 Model: QIC38 Input: DC 5V/2A 9V/1.7A 12V/1.25A Output: 10W Max Made in China
• Alignment matters - centering the device on the charging surface ensures the
fastest and most ecient charge
• Thick phone cases as well as some materials can interfere with the ability to charge
• This is a high speed wireless charger. Make the most of the charger by using the
USB-C cable and Quick Charge 3.0 wall plug that were packaged with it. Using a
dierent power source may charge your device at a slower speed.
quick tips
• Wireless charger
• USB-A to USB-C charging cable
• Quick Charge 3.0 wall plug
• Solid Red - Charging your device
Solid White - Fully charged
Flashing Red - Foreign object detection, pieces of metal or other materials may cause
overheating and damage your charger or phone. Remove them immediately
indicators
included
• Place the charger on a sturdy at surface
• Connect the quick charger 3.0 wall plug to the wall outlet using the USB-C cable
• If you need to use a dierent power source make sure it is a USB power supply of
DC 9V 2A minimum warning: please use UL compliant power supply
• Place your QI-enabled device onto the wireless charger and align the device with
the center of the charging surface or the device will not charge
• Remove credit cards or any card with a magnetic strip to prevent damage
to the cards before charging
• Charge time will vary by device
charging
• See the additional page for help setting up the charging cradle
setting up the cradle
• Double check that the USB-C cable and quick charger 3.0 wall plug are plugged in
• Certain phone cases may interfere with wireless charging. Remove the phone case
for best results.
• Double check the placement of the device on the wireless charger. For best results,
the center of the device should be on the center of the wireless charger
• Wireless charging is compatible with iPhone 8 and newer as well as other QI-enabled
devices. Please consult your devices user manual if you are unsure if your device
is compatible.
troubleshooting
• Remove credit cards and other cards with magnetic strips to prevent damage to
the cards
• Keep the charger away from heat and direct sunlight
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
• Immediately unplug it from its power source if it gets wet
• Remove the protective lm on the Quick Charge 3.0 wall plug before using
safety
Can’t get it to charge? Just have a question?
call us at: 877-698-4883 or: 877-MyTgtTech
e-mail us at: TargetTechSupport.com
need some help?
charging
indicator
First lift the cradle up and out of the
organizer so it is in the upright
position. Be sure not to force the
cradle as it only goes to about a 75º
incline. It will automatically click into
that position.
3 4
1
2
• If you’re having issues getting the cradle to the upright position, try pushing from the
bottom side of the base
• Take care when removing the charger from the cradle, as too much force may damage
the stand
installation tips
Can’t get the cradle upright? Have a question or comment?
call us at: 877-698-4883 or: 877-MyTgtTech
online at: TargetTechSupport.com
need some help?
charging cradle
Pull the charge cable through the
base and place the charger into the
back of the cradle.
There are two
notches on the
bottom of the
organizer to
hold the cable
in place: 1. At
the top of the
rst bend. 2.
Where the cable
exits the stand.
Make sure the
cable has slack,
so the cradle is
adjustable.
1
Next take your Apple Watch Magnetic
Charging Cable and put the USB end
through the bottom slot on the
charging stand.
®
charging
cradle
usb-c
port
back
top
wireless charging station
2