QNAP Turbo NAS Hardware User Manual © 2015. QNAP Systems, Inc. All Rights Reserved.
Thank you for choosing QNAP products! This user manual provides description of the hardware of the Turbo NAS and relevant guideline of certain functions. Please read carefully and strictly adhere to the instructions of the manual.
DISCLAIMER In no event shall QNAP Systems, Inc. (QNAP) liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation.
Regulatory Notice FCC Notice QNAP NAS comply with different FCC compliance classes. Please refer the Appendix for details. Once the class of the device is determined, refer to the following corresponding statement. ======================================================= FCC Class A Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
FCC Class B Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Symbols in this document This icon indicates the instructions must be strictly followed. Failure Warning to do so could result in injury to human body or death. This icon indicates the action may lead to disk clearance or loss OR Caution failure to follow the instructions could result in data damage, disk damage, or product damage.
Table of Contents Safety Warnings ................................................................................................. 8 Chapter 1. CPU and Memory Specifications ..................................................... 9 Chapter 2. Power Button and Reset Button Behavior .................................... 23 Chapter 3. USB One Touch Copy .................................................................... 24 Chapter 4. LED and Alarm Buzzer Specifications ...................................
Safety Warnings 1. The NAS can operate normally in the temperature of 0ºC–40ºC and relative humidity of 0%–95%. Please make sure the environment is well-ventilated. 2. The power cord and devices connected to the NAS must provide correct supply voltage (100W, 90–264V). 3. Do not place the NAS in direct sunlight or near chemicals. Make sure the temperature and humidity of the environment are in optimized level. 4. Unplug the power cord and all connected cables before cleaning.
Chapter 1. CPU and Memory Specifications Caution: Modifying the hardware, software, or firmware of the QNAP products will void the warranty. QNAP is not responsible for any form of damage or loss of data caused by modding the QNAP products. Users should bear their own risks of all sorts of possible data loss or system instabilities due to changing the hardware parts, modifying the default system firmware or installing any unauthorized third party applications on QNAP products.
TS-231+ TS-431+ Dual-core ARM™ Dual-core ARM™ Cortex™ -A15 1.4GHz Cortex™ -A15 1.4GHz Memory 1GB DDR3 1GB DDR3 Flash 512MB 512MB Memory replaceable No No Number of SODIMM 0 0 2 4 System CPU slots Number of hard drive slots System HS-210 CPU ARM 1.6GHz Memory 512MB DDR3 Flash 16MB Memory replaceable No Number of SODIMM slots Number of hard drive slots System CPU 0 2 TS-269H Dual-core Intel® 1.
System CPU TS-879 Pro TS-1079 Pro TS-879U-RP Dual-core Intel® Core™ Dual-core Intel® Core™ Dual-core Intel® Core™ i3 3.30 GHz i3 3.30 GHz i3 3.
System TS-1679U-RP CPU Dual-core Intel® Core™ Quad-core Intel® TS-EC1679U-RP i3 3.30 GHz Xeon™ 3.
System CPU Memory TS-853U TS-853U-RP Quad-core Intel® Quad-core Intel® Celeron™ 2.0 GHz (up Celeron™ 2.0 GHz (up to 2.41GHz) to 2.41GHz) 4GB/8GB DDR3 4GB/8GB DDR3 (Expandable RAM, up to (Expandable RAM, up to 8GB) 8GB) 512MB (USB DOM) 512MB (USB DOM) Yes (Compatible with Yes (Compatible with DDR3L-1333 DRAM) DDR3L-1333 DRAM) 2 2 8 8 Power supply unit 250W 2 x 250W System TS-1253U TS-1253U-RP Quad-core Intel® Quad-core Intel® Celeron™ 2.0 GHz (up Celeron™ 2.0 GHz (up to 2.
System TS-470U-SP TS-470U-RP Dual-core Intel® Dual-core Intel® Celeron™ 2.7 GHz Celeron™ 2.7 GHz Memory 2GB DDR3 2GB DDR3 Flash 512MB 512MB Yes (Compatible with Yes (Compatible with DDR3-1333 RAM) DDR3-1333 RAM) 2 2 4 4 CPU Memory replaceable Number of SODIMM slots Number of hard drive slots Power supply unit 250W (Upgradeable to redundant power) 2 x 250W PCI-E expansion slot No No System TS-870U-RP TS-1270U-RP Dual-core Intel® Dual-core Intel® Celeron™ 2.4 GHz Celeron™ 2.
System CPU IS-400 Pro Dual-core Intel® 1.1 GHz Memory 2GB DDR3 Flash 512MB (USB DOM) CPU replaceable No Memory replaceable Number of SODIMM slots Number of hard drive slots System CPU Yes (Compatible with DDR3-1333 RAM) 2 4 (2.5" only) TS-251C TS-251 / TS-251-4G Dual-core Intel® Dual-core Intel® Celeron™ 2.41 GHz (up Celeron™ 2.41 GHz (up to 2.58GHz) to 2.
System CPU Memory Flash Memory replaceable Number of SODIMM slots Number of hard drive slots IR sensor System CPU Memory Flash Memory replaceable Number of SODIMM slots Number of hard drive slots IR sensor TS-451 / TS-451-4G TS-451S Dual-core Intel® Dual-core Intel® Celeron™ 2.41 GHz (up Celeron™ 2.41 GHz (up to 2.58GHz) to 2.
System HS-251 / HS-251-2G Dual-core Intel® CPU Celeron™ 2.41 GHz (up to 2.
System TS-653 Pro / TS-653 Pro-8G TS-853 Pro-8G ® Quad-core Intel® Quad-core Intel CPU Memory Flash Memory replaceable Number of SODIMM slots Number of hard drive slots LCD panel IR sensor TS-853 Pro / Celeron™ 2.0 GHz (up Celeron™ 2.0 GHz (up to 2.41GHz) to 2.
System CPU Memory Flash Memory replaceable Number of SODIMM slots Number of hard drive slots LCD panel IR sensor TS-453S Pro TS-853S Pro (Formerly the (Formerly the SS-453 Pro) SS-853 Pro) Quad-core Intel® Quad-core Intel® Celeron™ 2.0 GHz (up Celeron™ 2.0 GHz (up to 2.41GHz) to 2.41GHz) 4GB DDR3L 4GB DDR3L (Expandable RAM, up to (Expandable RAM, up to 8GB) 8GB) 512MB 512MB Yes (DDR3L-1333 Yes (DDR3L-1333 SODIMM DRAM) SODIMM DRAM) 2 2 4 (2.5” only) 8 (2.
TVS-463-4G / TVS-663-4G / TVS-463-8G TVS-663-8G Quad-core AMD Quad-core AMD 2.4 GHz 2.
System CPU Memory Flash Memory replaceable Number of SODIMM slots Number of hard drive slots TVS-863-4G / TVS-863+-8G / TVS-863-8G TVS-863+-16G Quad-core AMD Quad-core AMD 2.4 GHz 2.
Chapter 2. Power button: Press to turn on or turn off. System All models Power Button and Reset Button Behavior Power button Power button (Hardware turn (Turn on) off) Press once 1.5 sec Power button (Force turn off) 5 sec Reset button: Press to reset the system settings. System All models Basic system reset Advanced system reset (1 beep) (2 beeps) 3 sec 10 sec Basic system reset (3 sec) Press the reset button for 3 seconds, a beep sound will be heard.
Chapter 3. USB One Touch Copy System All NAS models Number of seconds (press the one touch copy button to trigger data copy) 0.5 sec Data Copy by the Front USB Port The NAS supports instant data copy backup from the external USB device to the NAS or the other way round by the front one touch copy button. To use this function, follow the steps below: 1. Make sure a hard drive is installed and formatted on the NAS. The default network share Qusb or Usb is created. 2. Turn on the NAS. 3.
Chapter 4. LED and Alarm Buzzer Specifications The LED indicators of the NAS indicate the system status and information. When the NAS is turned on, check the following items to make sure the system status is normal. Note that the following LED information is applicable only when users have properly installed the hard drive, and connected the NAS to the network and the power supply. LED Color LED Status Description 1. Flashes green and red alternately every 0.5 sec 2. 3. 4. 5. 6. 1. 2. 3. 4. 5.
LED Color LED Status Description All the hard disk drives on the NAS are in standby mode. Off LAN Orange The disk data is being accessed from the network and a read/write error occurs during the process. Flashes orange The NAS is being accessed from the network. Orange The 10GbE network expansion card is installed. Green 10 GbE2 Green Off No 10GbE network expansion card is installed. The disk data is being accessed and a read/write error occurs during the process.
Beep alarm (for all NAS models) The beep alarm can be disabled in “System Administration” > “Hardware Settings”. Beep sound Number of Times Description 1. 2. Short beep (0.5 sec) 1 3. 4. The NAS is starting up. The NAS is being shut down (software shutdown). The user presses the reset button to reset the NAS. The system firmware has been updated. The user tries to copy the NAS data to the external storage device from the front USB port, but the data cannot be copied. Short beep (0.
Chapter 5. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation) Warning: The following instructions should only be performed by an authorized and trained technician. Strictly adhere to the instructions to install a RAM module on the NAS. Failure to do so could result in injury to human body or death. Before starting, please ensure that you turn off the NAS, disconnect the power adaptor, network cable(s), and also remove any other device/cable that is attached to the NAS.
1. Use a flathead screwdriver to loosen the screw on the memory module compartment at the bottom of the NAS and lift the compartment cover away. 2. To remove installed memory modules, pull the retention clips on each side so that the module tilts up for easy removal.
Note: Always ensure that a memory module is installed in the Primary (red) slot. If not, then the system will fail to start. When installing two memory modules, please ensure that they are the same size and ideally use the same type/model for both slots. 3. Slide the memory module to the slot at a 45-degree angle (approximately) and press the memory module down until it clips into place. Ensure the memory module sits properly with the clips in place. 4. Close the NAS cover and fasten the screw.
1. Loosen the three screws on the rear of the NAS. 2. Remove the case cover of the NAS gently. 3. Locate the memory slot. Make sure the slot is empty. Note: For TS-x53/x53S Pro, TS-451S, TS-651 and TS-851 models, always ensure that a memory module is installed in the Primary slot (red). If not, then the system will fail to start. When installing two memory modules, please ensure that they are the same size and ideally use the same type of RAM for both memory slots.
4. Grasp the edge of the memory module. Align the notch on the gold edge of the module with the notch in the memory slot. Slide the memory module to the slot at a 45-degree angle (approximately). 5. Gently press the memory module into the slot until it is seated fully. 6. Rotate the memory module towards the motherboard until the securing clips clicks into place. 7. Close the case cover and fasten the screws. Connect the power adaptor and cables back to the NAS. 8.
a. TS-451U and TS-453U: Loosen the six screws on the top of the NAS. b. TS-853U, TS-1253U: Loosen the two screws on the rear of the NAS. 6. Open the NAS.
7. Slide the memory module to the slot at a 45-degree angle (approximately). 8. Press the memory module down while holding the clips open. 9. Make sure the memory module sits in properly with the clips in place.
Note: For TS-x53U & TS-451U models, always ensure that a memory module is installed in the primary slot (red box in the below figure,) or the system will fail to start. When installing two memory modules, please ensure that they are the same size and ideally use the same type of RAM for both memory slots. The maximum supported memory is 8GB combined. 10. Close the NAS cover and fasten the screws. Connect the power adaptor and cables back to the NAS. 5.
QNAP provides a 4GB DDR3* RAM module and a 4GB DDR3 ECC** RAM module (optional purchase) for users to upgrade the memory of the NAS. Insert an extra RAM module on the motherboard of the NAS to upgrade the memory. The total memory will be shown in “System Information” of the administration page. *Applied models: TS-879U-RP, TS-1279U-RP, TS-1679U-RP, TS-870U-RP, TS-1270U-RP. **Applied models: TS-EC879U-RP, TS-EC1279U-RP, TS-EC1679U-RP. 1.
2. Hold the notch at the edge of the top cover. Remove the top cover in both hands. 3. Release the ejector clips gently by pulling them out of the sides of the RAM slot. 4. Grasp the edge of the RAM module. Align the notch on the gold edge of the RAM module with the notch in the RAM slot. Insert the RAM module to the RAM slot until it cannot go any further.
5.5 TS-251, TS-451 1. Remove the screws on the rear (top and bottom) of the NAS. If you have a 2-bay NAS, it will have two screws. A 4-bay NAS will have four. 2.
3. Remove the four inner screws (two on each side) of the hard drive cage. 4. If it is a 4-bay NAS, you will also need to remove two screws on the top of the hard drive cage. 5. Gently remove the hard drive cage from the NAS by lifting it out of its slot. 6. Always ensure that a memory module is installed in the Primary slot (red). If not, then the system will fail to start.
ensure that they are the same size and ideally use the same type of RAM for both memory slots. The maximum supported memory is 8GB combined. 7. Reattach the hard drive cage to the NAS. Please ensure that it correctly plugs into the slot. 8. Secure the hard drive cage by fastening the four inner screws (for the 4-bay NAS, please fasten the two additional top screws.) Then reattach the case cover of the NAS by gently sliding it back together. 9. Fasten the two/four screws onto the rear of the NAS. 10.
11. Connect the power adaptor and cables back to the NAS. 12. To check that the memory module is recognized by the NAS, power up the NAS and login the web interface as an administrator. Go to “System Status” > “System Information” and check the total memory in “Hardware Information”.
Chapter 6. Network Expansion Card Installation Warning: The following instructions should only be performed by an authorized and trained technician. Strictly adhere to the instructions to install a network expansion card on the NAS. Failure to do so could result in injury to human body or death. The TVS-x63 and TS-x79 Pro series provides expansion slots for network expansion. Insert an extra network expansion card (optional purchase) to the motherboard of the NAS to increase the network bandwidth.
Network Expansion Card Compatibility Bracket A (X520-T2) Intel® Ethernet Server Adapter X520-T2 (E10G42B) Bracket B 1. Intel® Ethernet Server Adapter X520-SR2 (E10G42BFSR) (X520-SR2/X520-DA2) 2. Intel® Ethernet Server Adapter X520-DA2 (E10G42BTDA) Bracket C (Emulex) 1. Emulex OneConnect 10GbE Network Adapters, SFP+ Direct attach copper (OCe11102-NX) 2. Emulex OneConnect 10GbE Network Adapters, Short reach optical (OCe11102-NM) 3.
4. Remove the case cover of the NAS gently. For TVS-463 only: Unscrew and remove the power supply unit.
5. Loosen the screws and remove the expansion slot cover. 6. Grasp the edge of the network expansion card. Align the notch on the gold edge of the card with the notch in the PCIe slot. Insert the network expansion card to the PCIe slot until it cannot go any further.
7. Fasten the screws. 8. Close the case cover and fasten the screws. Connect the power adaptor and cables to the NAS. 9. To check that the network expansion is recognized by the NAS, power up the NAS and login the web interface as an administrator. Go to “System Administration” > “Network” > “TCP/IP” and check the total number of network interfaces. 6.2 TS-879U-RP, TS-EC879U-RP, TS-1279U-RP, TS-EC1279U-RP, TS-1679U-RP, TS-EC1679U-RP 1. Turn off the NAS.
4. Hold the notch at the edge of the top cover. Remove the top cover in both hands. 5. Loosen the 4 screws as shown in the illustration. 6. Grasp the metal edge of the riser card module. Remove the module gently.
7. Loosen the screw and remove the expansion slot cover. 8. Insert the network expansion card to the PCIe slot until it cannot go any further. Then fasten the screw.
9. Grasp the metal edge of the riser card module. Align the notch on the gold edge of the riser card with the notch in the PCIe slot. Insert the riser card module to the PCIe slot until it cannot go any further. 10. Fasten the screws. Close the case cover and fasten the screws. 11. Connect the power adaptor and cables to the NAS. 12. To check that the network expansion is recognized by the NAS, power up the NAS and login the web interface as an administrator.
6.3 1. TS-870U-RP, TS-1270U-RP Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. 2. Before installing the network expansion card, put on an antistatic wrist strap to prevent electrostatic discharge. The crocodile clip should be connected to the ground. 3. Loosen the two screws on the rear of the NAS. 4. Hold the notch at the edge of the top cover. Remove the top cover in both hands. 5.
6. Grasp the edge of the expansion card. Align the notch on the gold edge of the card with the notch in the PCIe slot. Insert the network expansion card to the PCIe slot until it cannot go any further. 7. Fasten the screws. 8. Close the case cover and fasten the screws. Connect the power adaptor and cables to the NAS. 9. To check that the network expansion is recognized by the NAS, power up the NAS and login the web interface as an administrator.
Chapter 7. Install and Hot-swap Hard Drives Caution: Before starting, please ensure that you turn off the NAS, disconnect the power adaptor, network cable(s), and also remove any other device/cable that is attached to the NAS. Please ensure that you wear an antistatic wrist strap during the entire process to prevent electrostatic discharge. The crocodile clip should be connected to the ground. 7.1 Install Hard Drives Follow the below steps to install hard drives on the NAS. TS-453Mini 1.
a. For 3.5” HDDs, remove both brackets (pinch the end marked “pull” to pull and separate the bracket) from the tray. Place the hard drive on the tray and clip-in both brackets. b. For 2.5” HDDs/SSDs, secure the three screws in the back of the hard drive tray.
3. Insert the hard drive tray into the Turbo NAS all the way to the bottom and close the case cover.
TS-112P, TS-212P and TS-251C 1. Loosen the screws on the rear (top and bottom) of the NAS. Remove the case cover of the NAS by sliding it apart (see the underside of the NAS for visual indicators of the NAS case being locked/unlocked.) 2. Install the hard drives: a. For TS-112P: Place the hard drive in the hard drive cradle and slide it forward to lock it into the connector. Secure the screws on the slides of the hard drive. b.
and slide it forward to look it into the connector. Place the second hard drive on top of the first hard drive and secure the screws on the slides of both hard drives. Connect the SATA cable and power cable to the connectors as shown in the picture. 3. After installing the hard drives, cover the NAS with the case cover and fasten the round head screws. Then, place the NAS vertically on the stands.
7.2 Hard-swap Hard Drives The QNAP NAS is compatible with 2.5-inch/3.5-inch SATA hard disk drives from major hard disk brands. For the updated hard drive compatibility list, please visit http://www.qnap.com. Caution: QNAP disclaims any responsibility for product damage/malfunction or data loss/recovery due to misuse or improper installation of hard disks in any occasions for any reasons.
System Supports Supports Supports Supports 3.5-inch 2.5-inch SSD Hot-swapping SATA Hard SATA Hard Hard Drives Drives Drives (RAID 1 or above only) TS-1253U, TS-1253U-RP, TS-870U-RP, TS-1270U-RP, TS-470/470 Pro, TS-670/670 Pro, TS-870/870 Pro, TVS-463, TVS-663, TVS-863, TVS-863+ TS-451S, TS-453S Pro, No Yes Yes Yes TS-853S Pro, IS-400 Pro The NAS supports hot-swapping the hard drives when 1 member drive crashes in RAID 1, 1–2 member drives crash in RAID 5 or RAID 6.
Chapter 8. RAID Recovery The QNAP NAS supports exclusive RAID recovery technology to recover a failed RAID disk volume from unintentional disconnection or removal of the hard drives from the system. Using the RAID recovery, users can recover an inactive RAID 1, RAID 5, or RAID 6 volume to degraded mode, or an inactive RAID 0 and JBOD configuration to normal.
Standard QNAP RAID 5 RAID 5 Standard QNAP RAID 6 RAID 6 Degraded mode N-1 N-1 N-1 & N-2 N-1 & N-2 Read only protection N/A N-1, bad blocks N/A N-2, bad blocks (for immediate data found in the found in the backup & hard drive surviving drives of surviving drives of replacement) the array. the array.
Chapter 9. Use the LCD Panel This feature is only provided by the NAS models with LCD panels. Please visit http://www.qnap.com for details. The NAS provides a handy LCD panel for users to perform disk configuration and view the system information. When the NAS has started up, the server name and IP address will be shown. N A S 5 F 4 D E 3 1 9 . 2 5 4 . 1 6 0 0 . 1 0 0 For the first time installation, the LCD panel shows the number of hard drives detected and the IP address.
When RAID 1, RAID 5, or RAID 6 configuration is executed, the system will initialize the hard drives, create the RAID device, format the RAID device, and mount it as a volume on the NAS. The progress will be shown on the LCD panel. When it reaches 100%, the RAID volume can be accessed. Users can create share folders and upload files to the folders on the NAS.
View system information by the LCD panel When the LCD panel shows the server name and IP address, press the “Enter” button to enter the Main Menu. The Main Menu consists of the following items: 1. TCP/IP 2. Physical disk 3. Volume 4. System 5. Shut down 6. Reboot 7. Password 8. Back 1. TCP/IP The following options are available: LAN1 IP Address LAN1 Subnet Mask LAN1 Gateway LAN 1 PRI. DNS LAN 1 SEC.
3. Volume This section shows the disk configuration of the NAS. The first line shows the RAID configuration and storage capacity; the second line shows the member drive number of the configuration. R A I D 5 D r i v e 7 5 0 G B 1 2 3 4 If there is more than one volume, press the “Select” button to view the information. The following table shows the description of the LCD messages for RAID 5 configuration. 4.
7. Password The default password of the LCD panel is blank. Enter this option to change the password of the LCD panel. Select “Yes” to continue. C h a n g e P a s s w o r d → N o Y e s Enter a password of maximum 8 numeric characters (0-9). When the cursor moves to “OK”, press the “Enter” button. Verify the password to confirm the changes. N e w P a s s w o r d : O K 8. Back Select this option to return to the main menu.
Chapter 10. Install Power Supply Unit Note: This section applies to rackmount NAS models only. The power supply units of TS-879U-RP and TS-EC879U-RP should only be replaced by an authorized and trained technician. 10.1 1U Turbo NAS Note: The following instructions should only be performed by an authorized and trained technician. To install a redundant power supply unit to the 1U Turbo NAS, follow the steps below. 1. Turn off the NAS. 2. Remove the screw and dummy plate. 3.
4. Fasten the screw tightly. 5. Turn on the NAS. Note: To replace a failed power supply unit, turn off the NAS. Then remove the failed unit safely and repeat steps 3-5 above to install a new power supply unit. 10.2 TS-470U-RP/SP Note: The following instructions should only be performed by an authorized and trained technician. Follow the steps below to replace a failed power supply unit on the TS-470U-RP/SP. 1. Turn off the NAS. 2. Press the green lever and remove the defective power supply unit.
3. Insert a new power supply unit and push it to the end. 4. Turn on the NAS. Warning: The NAS supports replacing the redundant power supply unit without turning off the server when redundant power supply mode is enabled. However, users are strongly recommended to turn OFF the NAS before replacing the power supply unit to reduce the risk of electric shock. A second power supply unit can be installed on a single power (SP) rackmount NAS model to upgrade the SP model to redundant power (RP) model. 10.
2. Hold the black handler and press and hold the green button firmly. 3. Unplug the failed power supply.
4. Plug in a new power supply to the NAS. 5. Turn on the NAS. Enable warning alert for redundant power supply on the web-based interface: If two power supply units (PSU) have been installed on the NAS and connected to the power sockets, both PSU will supply the power to the NAS (applied to 1U and 2U models). Users can enable redundant power supply mode in “System Administration” > “Hardware” to receive warning alert for the redundant power supply.
WARNING: RISK OF ELECTRIC SHOCK The connectors on the back panel (bracketed parts below) contain high voltage. Do NOT touch these parts to avoid the risk of electric shock to the maintenance operator.
Technical Support QNAP provides dedicated online support and customer service via instant messenger. Online Support: http://helpdesk.qnap.com/ Forum: http://forum.qnap.com Technical Support in the USA and Canada: Email: q_supportus@qnap.
GNU GENERAL PUBLIC LICENSE Version 3, 29 June 2007 Copyright © 2007 Free Software Foundation, Inc. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works.
For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well. To “convey” a work means any kind of propagation that enables other parties to make or receive copies.
the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures. 4. Conveying Verbatim Copies.
to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate. 6. Conveying Non-Source Forms.
Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage.
section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying. 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions.
meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. Automatic Licensing of Downstream Recipients.
License. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement).
contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law. 12. No Surrender of Others' Freedom.
Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
Appendix A: Product Compliance Class FCC CE NAS Models TS-EC1679U-RP, TS-EC1279U-RP, TS-EC879U-RP, TS-1679U-RP, TS-1279U-RP, TS-1270U-RP, TS-1253U-RP, Class A Class A TS-1253U, TS-879U-RP, TS-870U-RP, TS-853U-RP, TS-453U-RP, TS-1079 Pro, TS-879 Pro, TS-853U, TS-453U, TS-451U, TVS-871U-RP, TVS-1271U-RP TS-853S Pro, TS-453S Pro, TS-870 Pro, TS-853 Pro, TS-670 Pro, TS-653 Pro, TS-470 Pro, TS-453 Pro, TS-253 Pro, TS-431+, TS-231+, TS-451S, TS-870, TS-851, Class B Class B TS-670, TS-651, TS-470, TVS-863
