TXi 5400 Bedienungsanleitung · Owner's Manual
Inhaltsverzeichnis Installation Installationshinweise, Einbau des Verstärker, Elektrische Anschlüsse 3 TXi 5400 Funktionen & Bedienelemente Lautsprecher- & Cinchanschlüsse 4-Kanal-Modus / Stereo Front- und Hecksystem Lautsprecher- & Cinchanschlüsse 2-Kanal-Modus / 2 Mono Subwoofer gebrückt Lautsprecher- & Cinchanschlüsse 3-Kanal-Modus / Stereo und 1 Subwoofer gebrückt 4 5 6 7 Fehlerbehebung 8 Technische Daten 9 OWNER'S MANUAL in english on Page 11 2
Installation Installationshinweise Achten Sie bei der Installation darauf, dass keine serienmäßig im Kfz vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw. entfernt werden. Vergewissern Sie sich, dass der Verstärker an dem Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu kleine, abgeschlossene Gehäuse ohne Luftzirkulation, in die Nähe von wärmeabstrahlende Teilen oder elektronische Steuerungen des Fahrzeuges.
Funktionen & Bedienelemente HI-/LOW PASS - Regler CH1/2 & CH3/4 HI PASS (Hochpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach unten. Die Trennfrequenz ist stufenlos von 10Hz bis 1200Hz (1.2kHz) regelbar. LOW PASS (Tiefpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach oben. Die Trennfrequenz ist stufenlos von 30Hz bis 150Hz regelbar.
Lautsprecher- & Cinchanschlüsse 4-Kanal-Modus Stereo Front- und Hecksystem Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Front- und Hecklautsprecher mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + 1CH - und + 2CH - und + 3CH - und + 4CH -).
Lautsprecher- & Cinchanschlüsse 2-Kanal-Modus Mono 2 Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die beiden Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / CH1/2 + Mono Bridged - und CH3/4 + Mono Bridged -).
Lautsprecher- & Cinchanschlüsse 3-Kanal-Modus Stereo Front- oder Hecksystem& Mono Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Lautsprecher und den Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + CH 1 - und + CH 2 - und den Subwoofer mit CH3/4 + Mono Bridged -).
Fehlerbehebung Fehler: keine Funktion Ursache: 1. Die Verbindungskabel sind nicht korrekt angeschlossen. 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. 3. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen. Fehler: kein Ton aus Lautsprecher Ursache: 1. Die Lautsprecherkabel oder Cinchkabel sind nicht korrekt angeschlossen oder defekt. 2. Die Lautsprecher sind defekt. 3.
Technische Daten Kanäle Watt RMS/MAX. an 4 Ohm Watt RMS/MAX. an 2 Ohm Watt RMS/MAX.
Table of Contents Installation Installation Notes, Installation of the Amplifier, Electrical Connections 12 TXi 5400 Functions & Controls Speaker- & RCA Connections 4-Channel-Mode / Stereo Front- and Rearsystem Speaker- & RCA Connections 2-Channel-Mode / 2 Mono Subwoofers bridged Speaker- & RCA Connections 3-Channel-Mode / Stereo and 1 Subwoofer bridged 13 14 15 16 Trouble Shooting 17 Specifications 18 11
Installation Installation Notes The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable installation.
Functions & Controls HI-/LOPASS CH1/2 & CH3/4 HI PASS (HighPass) Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 10Hz up to 1200Hz (1.2kHz). LOW PASS (LowPass) Controls the frequency response of your speakers upwards. The Cut-off frequency is continously variable from 30Hz up to 150Hz.
Speaker & RCA Connections 4-Channel-Mode Stereo Front- and Rearsystem RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 + and - CH3 and CH4 +) of the amplifier. • The minimum final speaker impedance must not be lower than 2 Ohms per channel.
Speaker & RCA Connections 3-Channel-Mode 2 Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1/2 - Mono bridged + and the subwoofer with CH3/4 - Mono bridged +) of the amplifier. • The minimum final subwoofer impedance must not be lower than 4 Ohms per channelpair.
Speaker & RCA Connections 3-Channel-Mode Stereo Front- or Rearsystem & Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 + and the subwoofer with CH3/4 - Mono bridged +) of the amplifier.
Troubleshooting System does not turn on 1. Check all fuses. 2. Check all connections. 3. Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit’s +12 volt and remote leads to localize the problem. Noise problems 1.Check the speaker wiring 2.Speakers are damaged No Signal at all Channels 1. Set Balance and Fader from head unit on Zero-Position 2.
Specifications Channels Watts RMS/MAX. into 4 Ohm Watts RMS/MAX. into 2 Ohm Watta RMS/MAX.
Distribution: Audio Design GmbH Am Breilingsweg 3 76709 Kronau / Germany Tel. +49(0)7253/9465-0, Fax 9465-10 www.audiodesign.