BEDIENUNGSANLEITUNG USER’S MANUAL ZEUS POWER DIGITAL CLASS D 2-CHANNEL AMPLIFIER ZXR600/2
DEUTSCH SICHERHEITSHINWEISE DAS VON IHNEN ERWORBENE GERÄT IST NUR FÜR DEN BETRIEB AN EINEM 12-V-BORDNETZ EINES FAHRZEUGS AUSGELEGT. Andernfalls besteht Feuergefahr, die Gefahr eines elektrischen Schlages oder anderer Verletzungen. BITTE KEINE BEDIENUNG DES SOUNDSYSTEMS AUSFÜHREN, WELCHE VOM SICHEREN LENKEN DES FAHRZEUGS ABLENKEN KÖNNTE. Führen Sie keine Bedienungen aus, die Ihre Aufmerksamkeit längere Zeit in Anspruch nehmen.
DEUTSCH BEIM BOHREN VON LÖCHERN, BESTEHENDE KOMPONENTEN, LEITUNGEN UND KABEL DES FAHRZEUGS NICHT BESCHÄDIGEN. Wenn Sie bei der Installation Löcher in das Fahrzeugchassis bohren, achten Sie unbedingt darauf die Kraftstoffleitungen, den Benzintank, elektrische Kabel und andere Leitungen nicht zu beschädigen, zu berühren oder zu blockieren. AUF KORREKTE ANSCHLÜSSE ACHTEN. Bei fehlerhaften Anschlüssen besteht Feuergefahr, Kurzschlussgefahr und es kann zu Schäden am Gerät kommen.
DEUTSCH ENTSORGUNG Elektro- und Elektronikgeräte – Informationen für private Haushalte Das Elektro- und Elektronikgerätegesetz (ElektroG) enthält eine Vielzahl von Anforderungen an den Umgang mit Elektro- und Elektronikgeräten. Die wichtigsten sind hier zusammengestellt. 1. Getrennte Erfassung von Altgeräten Elektro- und Elektronikgeräte, die zu Abfall geworden sind, werden als Altgeräte bezeichnet. Besitzer von Altgeräten haben diese einer vom unsortierten Siedlungsabfall getrennten Erfassung zuzuführen.
DEUTSCH 4. Datenschutz-Hinweis Altgeräte enthalten häufig sensible personenbezogene Daten. Dies gilt insbesondere für Geräte der Informations- und Telekommunikationstechnik wie Computer und Smartphones. Bitte beachten Sie in Ihrem eigenen Interesse, dass für die Löschung der Daten auf den zu entsorgenden Altgeräten jeder Endnutzer selbst verantwortlich ist. 5.
DEUTSCH TECHNISCHE DATEN Modellbezeichnung ZXR600/2 Kanäle 2 Schaltung Digital Class D AUSGANGSLEISTUNG RMS @ 14,4 V Watt @ 4 Ohm Watt @ 2 Ohm Watt @ 4 Ohm gebrückt 2 x 175 2 x 300 1 x 600 Lautsprecherimpedanz 2 - 8 Ohm Frequenzgang –3dB 4 - 39000 Hz Dämpfungsfaktor > 300 Signal-Rauschabstand 107 dB Klirrfaktor @ 1W/RMS < 0,02 % Eingangsempfindlichkeit 5 - 0,2 V Filter Frequenzweichenmodus Hochpassfilter Tiefpassfilter Bass Boost Full - HP - LP/BP 10 - 500 Hz 50 - 5000 Hz 0 - 12 dB @ 4
DEUTSCH MECHANISCHE INSTALLATION • Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw.entfernt werden. • Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu kleine abgeschlossene Gehäuse ohne Luftzirkulation oder in der Nähe von wärmeabstrahlenden Teilen oder elektronischen Steuerungen des Fahrzeugs.
DEUTSCH ELEKTRISCHE ANSCHLÜSSE VOR DEM ANSCHLIESSEN Für den fachgerechten Anschluss des Soundsystems sind geeignete Kabelsets im Fachhandel erhältlich. Achten Sie beim Kauf auf einen ausreichenden Kabelquerschnitt (siehe Tabelle auf der nächsten Seite) und den passenden Sicherungswert der Kabel. Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten.
DEUTSCH 3 +12V Verbinden Sie den 12 Volt Anschluss des Verstärkers mit dem 12 Volt Pluspol der Fahrzeugbatterie mit dem dafür vorgesehen Kabel (siehe dazu die Tabelle unten). 4 GERÄTESICHERUNG Der Verstärker besitzt prinzipbedingt keine interne Gerätesicherung. Verwenden Sie daher die im Lieferumfang enthaltene Sicherung (50 A) samt Halterung und installieren diese in das Stromkabel nahe des 12 Volt Anschlusses des Verstärkers.
DEUTSCH FUNKTIONSBESCHREIBUNG 6 7 LINE INPUT LINE OUTPUT L L 8 9 HIGH LEVEL INPUT 10 11 AUTO TURN-ON DC VOX OFF LEVEL HIGH PASS BLC POWER REMOTE LOW PASS PROTECT BASS BOOST BP X-OVER MODE MIN R R MAX 10 Hz 500 Hz 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP 12 13 14 15 16 6 LINE INPUT Verbinden Sie die LINE INPUT Cinch-Eingänge mit dem Steuergerät.
DEUTSCH 10 BLC REMOTE Der Anschluss BLC REMOTE ist zum Anschluss des Kabels der im Lieferumfang enthaltenen Basspegel-Fernbedienung. Mit dieser kann der Bass-Pegel z.B. vom Fahrersitz aus eingestellt werden. Verwenden Sie nur die mitgelieferte Bass-Fernbedienung sowie das dazugehörige Kabel. Die Basspegel-Fernbedienung funktioniert nur in der Betriebsart LP/BP (Tiefpass-/Bandpass-Modus). 11 POWER/PROTECT Leuchtet diese LED grün, ist der Verstärker betriebsbereit.
DEUTSCH ANWENDUNGSBEISPIEL A OFF LINE INPUT HIGH LEVEL INPUT LINE OUTPUT BLC AUTO TURN-ON POWER DC VOX OFF L L LEVEL PROTECT REMOTE HIGH PASS LOW PASS BASS BOOST BP X-OVER MODE MIN R MAX R Verstärker Cinch Ausgänge Cinch Eingänge FL L FR R 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP Belegung Steuergerät 10 Hz 500 Hz FULL oder HP 2-8Ω GND BRIDGED REM L +12V IN/OUT R SPEAKER ZXR 600/2 OUTPUT POWER INPUT REM 2-8Ω ANWENDUNGSBEISPIEL B DC LINE INPUT HIGH LEVEL INPUT LINE
DEUTSCH ANWENDUNGSBEISPIEL C VOX LINE INPUT HIGH LEVEL INPUT LINE OUTPUT BLC AUTO TURN-ON POWER DC VOX OFF L L LEVEL PROTECT REMOTE HIGH PASS LOW PASS BASS BOOST BP X-OVER MODE MIN R MAX R Steuergerät Verstärker Cinch Eingänge RL/SUB OUT L RR/SUB OUT R 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP LP/BP Belegung Cinch Ausgänge 10 Hz 500 Hz GND REM IN/OUT BRIDGED L +12V R SPEAKER ZXR 600/ 2 OUTPUT POWER INPUT 4-8Ω ANWENDUNGSBEISPIEL D DC LINE INPUT HIGH LEVEL INPUT LINE
DEUTSCH FEHLERBEHEBUNG ACHTUNG Sämtliche Hinweise dieser Fehlerbehebung beziehen sich auf das gesamte Soundsystem und deren Einzelkomponenten. Unter Umständen entspricht die Ausstattung Ihres Geräts nicht den in den Hinweisen beschriebenen Funktionen. Überspringen Sie dann diesen Punkt und machen mit dem nächsten weiter.
DEUTSCH DIE POWER LED LEUCHTET, ABER ES KOMMT KEIN TON AUS DEN LAUTSPRECHERN Überprüfen Sie folgende Schritte: Niederpegelmodus: Sind die RCA/Cinchkabel am Radio/Steuergerät und am Verstärker korrekt angeschlossen? • Die RCA/Cinchkabel sind korrekt angeschlossen. Es könnte ein RCA/Cinchkabel defekt sein. Überprüfen Sie die Funktion der RCA/Cinchkabel an einem anderen Audiogerät. Ersetzen Sie gegebenenfalls das defekte RCA/Cinchkabel.
DEUTSCH FEHLERBEHEBUNG VERZERRUNGEN ODER ZISCHGERÄUSCHE SIND AUS DEN LAUTSPRECHERN ZU HÖREN Überprüfen Sie folgende Schritte: Ist ein Eingangspegelregler am Verstärker zu hoch eingestellt? Drehen Sie den Regler langsam zurück, bis ein sauberes Audiosignal zu hören. Ist der Bass Boost (Bassanhebung) am Verstärker zu hoch eingestellt? Drehen Sie den Regler langsam zurück, bis ein sauberes Audiosignal zu hören.
DEUTSCH VERSTÄRKER AKTIVIERT DIE SCHUTZSCHALTUNG / DIE PROTECT LED LEUCHTET Überprüfen Sie folgende Schritte: Kurzschluss an den Lautsprecherkabeln • Klemmen Sie zunächst alle Lautsprecherkabel am Verstärker ab. Überprüfen Sie mit einem Multimeter die ohmsche Impedanz jedes Lautsprechers, indem sie zwischen dessen Plus- und Minusleitung messen. Bei handelsüblichen Lautsprechern schwankt der Wert zwischen 3 und 5 Ohm. Die Werte bei niederohmigen Subwoofern können geringer sein.
ENGLISH SAFETY INSTRUCTIONS THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE. Otherwise fire hazard, risk of injury and electric shock consists. PLEASE DO NOT MAKE ANY OPERATION OF THE SOUND SYSTEM, WHICH DISTRACT YOU FROM A SAFE DRIVING. Do not make any procedures, which demand a longer attention. Perform these operations not until you have stopped the vehicle on a safe place. Otherwise the risk of accident consists.
ENGLISH MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND SYSTEM SUFFICIENTLY. Otherwise the device and components may get loose and act as dangerous objects, which could cause serious harm and damages in the passenger room. ENSURE NOT TO DAMAGE COMPONENTS, WIRES AND CABLES OF THE VEHICLE WHEN YOU DRILL THE MOUNTING HOLES.
ENGLISH TECHNICAL SPECIFICATIONS Model ZXR600/2 Channels 4 Circuit Digital Class D OUTPUT POWER RMS @ 14.
ENGLISH MECHANICAL INSTALLATION • Avoid any damages on the components of the vehicle like air bags, cables, board computer, seat belts, gas tank or the like. • Ensure that the chosen location provides a sufficient air circulation for the amplifier. Do not mount the device into small sealed spaces without air circulation or near by heat dispersing parts or electrical parts of the vehicle. • All cables must be as short as possible to avoid losses and interferences.
ENGLISH ELECTRICAL INTERCONNECTION BEFORE CONNECTING For the professional installation of a sound system, car audio retail stores offers appropriate wiring kits. Ensure a sufficient profile section (refer to the table on the next page) and a suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
ENGLISH 4 FUSE The amplifier inherently has no internal device fuse. Use the supplied fuse (50 A) with the fuse holder and install it in the power cable between the 12 Volt pole of the vehicle battery and next to the +12V terminal of the amplifier. The distance between the fuse and the amplifier should not exceed 30 cm. 5 ADDITIONAL CABLE FUSE (NOT INCLUDED) Install an extra fuse (not included) for the +12V power cable near the battery to secure the power cable.
ENGLISH DESCRIPTION OF OPERATION 6 7 LINE INPUT LINE OUTPUT L L 8 9 HIGH LEVEL INPUT 10 11 AUTO TURN-ON DC VOX OFF LEVEL HIGH PASS BLC POWER REMOTE LOW PASS PROTECT BASS BOOST BP X-OVER MODE MIN R R MAX 10 Hz 500 Hz 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP 12 13 14 15 16 6 LINE INPUT Connect the LINE INPUT RCA jacks with the head unit by using appropriate audio signal cables.
ENGLISH 10 BLC REMOTE The BLC REMOTE port is for connecting the cable of the included bass level remote controller. With this, the bass level can be e.g. be adjusted from the driver’s seat. Only use the supplied bass remote controller and the associated cable. The bass level remote controller only works in LP/BP mode (LowPass/Bandpass). 11 POWER/PROTECT If the LED lights up in green, the amplifier is ready for operation. If the LED lights up in red, there is a malfunction.
ENGLISH APPLICATION EXAMPLE A OFF LINE INPUT HIGH LEVEL INPUT LINE OUTPUT BLC AUTO TURN-ON POWER DC VOX OFF L L LEVEL PROTECT REMOTE HIGH PASS LOW PASS BASS BOOST BP X-OVER MODE MIN R MAX R Amplifier RCA Outputs RCA Inputs FL L FR R 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP Assignment Head Unit 10 Hz 500 Hz FULL or HP 2-8Ω GND BRIDGED REM L +12V IN/OUT R SPEAKER ZXR 600/2 OUTPUT POWER INPUT REM 2-8Ω APPLICATION EXAMPLE B DC LINE INPUT HIGH LEVEL INPUT LINE OUTPUT
ENGLISH APPLICATION EXAMPLE C VOX LINE INPUT HIGH LEVEL INPUT LINE OUTPUT BLC AUTO TURN-ON POWER DC VOX OFF L L LEVEL PROTECT REMOTE HIGH PASS LOW PASS BASS BOOST BP X-OVER MODE MIN R MAX R Amplifier RCA Outputs RCA Inputs RL/SUB OUT L RR/SUB OUT R 50 Hz 5 kHz 0 dB 12 dB FULL HP LP/BP Assignment Head Unit 10 Hz 500 Hz LP/BP GND REM IN/OUT BRIDGED L +12V R SPEAKER ZXR 600/ 2 OUTPUT POWER INPUT 4-8Ω APPLICATION EXAMPLE D DC LINE INPUT HIGH LEVEL INPUT LINE OUTPUT
ENGLISH TROUBLE SHOOTING CAUTION All instructions in this trouble shooting refer to the entire sound system and its individual components. The features of your device may not match the functions described in the notes. Then skip this point and move on to the next one. NO FUNCTION / THE POWER LED IS NOT ILLUMINATED First check the fuse of the routed power cable on the vehicle battery The fuse is defective Replace the defective fuse with an equivalent one, never with a higher value. • The fuse fails again.
ENGLISH THE POWER LED IS ON, BUT NO SOUND COMES FROM THE SPEAKERS Check the following steps: Low level mode: Are the RCA cables on the head unit and on the amplifier correctly connected? • The RCA cables are correctly connected. Then an RCA cables could be defective. Check the function of the RCA cables on another audio device. If necessary, replace the defective RCA cables.
ENGLISH TROUBLE SHOOTING DISTORTION OR HISSING NOISE CAN BE HEARD FROM THE SPEAKERS Check the following steps: Is a input level controller on the amplifier set too high? Slowly turn the controller back until you hear a clean audio signal. Is the Bass Boost controller on the amplifier set too high? Slowly turn the controller back until you hear a clean audio signal.
ENGLISH AMPLIFIER ACTIVATES THE PROTECTIVE CIRCUIT / THE PROTECT LED LIGHTS UP Check the following steps: Short circuit on the speaker cables • First disconnect all speaker cables from the amplifier. Use a multimeter to check the ohmic impedance of each loudspeaker by measuring between its plus and minus lines. With standard loudspeakers the value fluctuates between 3 and 5 ohms. The values for low-resistance subwoofers can be lower. • The measurement shows a resistance value of less than 0.
ZEUS POWER Audio Design GmbH Am Breilingsweg 3 · D-76709 Kronau/Germany Tel. +49 7253 - 9465-0 · Fax +49 7253 - 946510 www.audiodesign.de - www.hifonics.