Instructions / Assembly

ManualsBrandsHigh Tech Pet ManualsKitchenPower Pet Large Electronic Fully Automatic Dog and Cat Electric Pet Door for Pets Up to 100 lb.

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION

Product Description:

Your new POWER PET Electronic Pet Door is like no

other pet door made. Patented POWER PET

elec-

tronic pet doors are fully automatic, motor driven and

open completely under their own power. Activated by an

ultrasonic pet collar, your new POWER PET door will

keep out stray animals. It is secure against wind, rain,

cold and snow and provides much better insulation than

a conventional ap door. Your new POWER PET door

features an attractive, high-strength door panel that

quickly and quietly powers upward disappearing into the

stylish housing. Your pets are empowered to come and

go as they please while their animal friends are politely

asked to stay out.

POWER PET doors increase home security with a

special automatic, deadbolt locking feature that guards

against would-be intruders. Only the coded signal from

your pet’s collar will open the Power Pet door.

Only Power Pet doors feature an ingenious directional

sensing system that operates a fully automatic, motor

driven panel. The signal emitted from your pet’s collar

tells the Power Pet door how far away your pet is and the direction in which your pet is traveling. This allows the Power

Pet to work like magic, opening only when your pet is on a direct approach, not when it is just wandering by and not when

it is sitting or sleeping next to the door.

Please Read All Instructions Carefully B

efore Attempting to

Install or Operate Your Power Pet Door.

Fully Automatic Pet Door

U.S. PATENT # 5,872,516

BATTERY

COMPARTMENT

(BATTERY OPTIONAL)

MOUNTING SCREW

COVERS (8)

DOOR PANEL

Power Input

Jack

Power Input

Jack

CONTROL PANEL

HIGH STRENGTH

ABS COMPOSITE

HOUSING

ULTRASONIC SENSOR

Summary of content (12 pages)

PAGE 1
TM U.S. PATENT # 5,872,516 Fully Automatic Pet Door Please Read All Instructions Carefully Before Attempting to Install or Operate Your Power Pet Door. INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION BATTERY COMPARTMENT CONTROL PANEL (BATTERY OPTIONAL) HIGH STRENGTH ABS COMPOSITE HOUSING MOUNTING SCREW COVERS (8) DOOR PANEL Power Input Jack Power Input Jack Product Description: Your new POWER PET Electronic Pet Door is like no other pet door made.
PAGE 2
ALL NEW DESIGN! After selling thousands of our original POWER PET, PP models we are very pleased to introduce our All New, completely redesigned and restyled PX Model. We listened to the feedback of hundreds of customers and threw in a few ingenious, new ideas of our own to bring you the ultimate combination of security, style and convenient features. The PX model, which features an extremely slim design, is less than 2 inches deep. This allows it to be mounted flush to your door or wall.
PAGE 3
INSTALLATION OVERVIEW power pet door outer frame optional wall adapter tunnel WALL INSTALLATION DOOR INSTALLATION outside frame outside frame optional wall adapter tunnel AC POWER adapter PLUGS IN HERE _______________________________________________________________________________________________________________________________________ High Tech Pet Products, Inc. www.hightechpet.
PAGE 4
POSITIONING THE OPENING ON DOOR OR WALL: 1” Reference Line h Measure height of animal’s chest Opening is 1” lower than height of animal’s chest CUT-OUT DIMENSIONS: Model PX-1 Model PX-2 Frame thickness 17.25 11.25” Reference Line 8.88 Final cut out size should include the thickness of any additional wall framing (not required for door mount or when using optional wall mount kit) Reference Line 12.
PAGE 5
INSTALLING YOUR POWER PET DOOR This is the easy part. Install the POWER PET and Outside Frame as shown below. 1. Cut Hole (wall installations will require framing) 2. Install Power Pet door See installation notes Door or Wall OUTSIDE INSIDE 3.
PAGE 6
IMPORTANT INSTALLATION NOTES: a) When installing the inside mounting screws, make sure they are only moderately tight. Over tightening will cause your Power Pet door housing to conform to any irregularities in the flatness of your door or wall and will cause the door panel to slow, stick or malfunction. Just tighten the screws until they stop. That is enough to insure that the installation is secure. Should your door panel malfunction during the initial power up, loosen each mounting screw and re-test.
PAGE 7
Battery Operation Whenever AC Power is unavailable and a charged battery is installed, the front panel indicators go into a low power mode where they blink every four seconds instead of remaining on continuously. This feature allows the battery to power the door for up to two months or 500 openings. ADVANCED FEATURES INTRINSICALLY SAFE OPERATION The POWER PET electronic pet door is intrinsically safe. It uses an electric motor and cable drive to lift the door panel.
PAGE 8
4 WAY ACCESS CONTROL: Individual activation buttons for the inside and outside sensors give you a 4-way access control system. You can allow your pet to come in but not go out, go out but not come in, come in and out or close and lock the door altogether AUTOMATIC CLOSE CONTROL: Your POWER PET PX Features a smart sensing circuit that keeps the door panel open as long as it is receiving the signal from your pet’s collar. Once your pet has moved completely through the opening, the panel immediately closes.
PAGE 9
3. T o close, first line up the slots at one end of the unit and squeeze together. Then squeeze together on the opposite end until the unit snaps shut. Your High Tech MS-2 or MS-2A ultrasonic transmitter collar will operate for 3 to 5 months on a single, easily replaceable battery. REPLACING THE MS-4 BATTERY If you are using the latest High Tech Pet MS-4 Digital Microsonic Collar use the following instructions for replacing the battery. 1, I nsert screwdriver or knife in end slot and pry open. 2.
PAGE 10
MANY CONVENIENT ACCESSORIES! We’ve added all sorts of great new options to make your POWER PET PX the most versatile pet door you’ll find. EXTRA PET COLLARS: Model MS-2 Standard, or MS-2A Sealed Ultrasonic Transmitter Collar Pet D o One Model MS-2 or MS2-A Collar comes standard with your POWER PET TM Door. You may wish to purchase an Extra collar for each additional pet and keep one or two more as spares. Lightweight and comfortable on all cats and dogs.
PAGE 11
u nD Bar r SOUND BARRIER Model SBR-1 Indoor Sonic alarm keeps your pet off furniture, away from the kitchen table or out of an entire room. Operated from your pet’s standard MS-2 transmitter included with your POWER PET Door. Also, operated by the optional RC-7000X collar. Order one for each pet restricted area. r i e r YARD BARRIER arr d B ie a ne Con t HUMANE CONTAIN Model HC-7000X Simply, the Most Advanced, Most Effective, Most Humane electronic pet fence made.
PAGE 12
High Tech Pet Products, Inc. 2476 Palma Drive, Suite A Ventura, CA 93003 www.hightechpet.com Rev.