Fully Automatic Pet Door INSTALLATION & OPERATING INSTRUCTIONS U.S.
INTRODUCTION Product Description: Your new POWER PET Electronic Pet Door is like no other pet door made. Patented POWER PETTM electronic pet doors are fully automatic, motor driven and open completely under their own power. Activated by an ultrasonic pet collar, your new POWER PET door will keep out stray animals. It is secure against wind, rain, cold and snow and provides much better insulation than a conventional flap door.
POWER PET doors increase home security with a special automatic, deadbolt locking feature that guards against would-be intruders. Only the coded signal from your pet’s collar will open the Power Pet door. Only Power Pet doors feature an ingenious directional sensing system that operates a fully automatic, motor driven panel. The signal emitted from your pet’s collar tells the Power Pet door how far away your pet is and the direction in which your pet is traveling.
Your POWER PET door package includes: • O ne Pet Transmitter Collar (Model MS-4 or MS-5 Ultrasonic Transmitter Collar) • 1 10 volt AC Adapter (connects to either Power Input Jack on edge of inside frame) • Pre-Fabricated Outside Frame • All Required Hardware (Wall Adapter Tunnel, Rechargeable Battery, Battery Charger Kit and Extra Transmitter Collars are sold separately.) PET COLLAR OPERATED Only the amazing POWER PET door uses our Patented directional ultrasonic sensing system.
INSTALLATION POWER PET DOOR MOUNTING YOUR POWER PET DOOR Your POWER PET door mounts flush to any door or wall. The hardest part of installing the POWER PET OPTIONAL WALL ADAPTER door is cutting the hole. If the unit is TUNNEL to be mounted in a door up to 1 ¾“ OUTER FRAME thick there is no framing necessary. The pre-made Outer Frame that came with your POWER PET door will provide a finished look to the opening.
POSITIONING THE OPENING ON DOOR OR WALL: POSITIONING THE OPENING ON THE DOOR OR WALL 1” Reference Line h Measure height of animal’s chest Opening is 1” lower than height of animal’s chest CUT-OUT DIMENSIONS: Model PX-1 Model PX-2 Frame thickness 17.25 11.25” Reference Line 8.88 Final cut out size should include the thickness of any additional wall framing (not required for door mount or when using optional wall mount kit) Reference Line 12.
INSTALLING YOUR POWER PET DOOR This is the easy part. Install the POWER PET and Outside Frame as shown below. 1. Cut Hole (wall installations will require framing) 2. Install Power Pet door See installation notes Door or Wall OUTSIDE INSIDE 3.
is enough to insure that the installation is secure. Should your door panel malfunction during the initial power up, loosen each mounting screw and re-test. b) Note that screw covers (not pictured) are provided to finish the screw holes. Once installed, the inside screw covers may be removed by twisting CLOCKWISE using a coin or flat head screwdriver. Twisting counter-clockwise will cause the screw covers to break. Initial Power up Plug the AC Adaptor into a nearby 110 VAC wall outlet.
Battery Installation To install the battery, open the battery compartment, and align the two battery lugs with the two lug sockets on the inner wall of the battery compartment. Then press the battery to mate it to the sockets. When done the battery should be flush with the wall, and the compartment cover should fit comfortably over the installed battery. An installed battery is automatically charged whenever the AC Adaptor is powering the door.
on the way down. This feature can be defeated in the unusual case that binding or other restriction slows the door closure to the point that it unnecessarily retracts. See the AUTOMATIC SAFETY RETRACT Section for more information. AUTO DEAD BOLT LOCKING FEATURE The POWER PET door uses a spring loaded locking pin which automatically snaps into its retaining hole when the movable panel comes to rest in the closed position. The pin can only be released when the motor applies tension to the cable.
Adjusting the Range When you first install the POWER PET PX door, pre-set both RANGE Controls - one at a time - to the desired activation distance as follows: - Enable just the INSIDE or OUTSIDE sensor and set that RANGE control to zero. - Hold the collar at about your pet’s height, pointing down toward the bottom of the door and at the desired activation distance from the door. - Slowly increase that RANGE Control setting until the panel opens. - Repeat this for the other sensor.
ADJUSTABLE HOLD UP TIME: The door is held open for a short time to let the pet get fully through the door before it starts closing. Depending on the speed your pet moves, you may adjust the hold up time as follows. 1. Press OFF button 2. Press and hold one or both sensor buttons to select hold up time 3. Press OFF button to save this hold up time 4. Press ON button to power the door. When shipped from the factory the hold up time is set to 4 seconds.
The opening motor is energized the entire time the door is open. So if using only a battery to power the door, and you do not have an AC Power Adaptor plugged into the door, use this feature sparingly to keep from discharging the battery in just a few hours. AUTOMATIC SAFETY RETRACT: Your POWER PET PX is intrinsically safe for all pets and people, including small children. The door panel weighs less than 2 lbs. and is closed smoothly by gravity (not the motor) and is too light to cause any physical injury.
PET COLLAR OPERATING INSTRUCTIONS Your POWER PET DOOR comes with a standard model MS-4 or MS-5 ultrasonic transmitter collar. Each collar includes a battery TEST button which illuminates a red LED when the battery is OK. If the LED fails to light, battery replacement is necessary. Note: To energize the MS-4 Collar, pull out and discard the PULL TAB which is protruding from the side of the collar.
REPLACING THE MS-4 BATTERY 1, Insert screwdriver or knife in end slot and pry open. 2. Separate top from bottom. 3. Replace battery top with the metal ring visible. 4. C arefully mate top and bottom while keeping aluminum speaker centered in the top hole. Squeeze together the top and bottom until both ends snap. ___________________________________________________________________________________________ 16 www.hightechpet.com High Tech Pet Products, Inc.
REPLACING THE MS-5 BATTERY 1. Unscrew the bottom cover. 2. Pry bottom from top on ends and on edges using small flat blade screwdriver 3. Remove bottom, note battery orientation 4. Remove and replace B3V1A battery 5. With new battery installed, close case. Squeeze until bottom flush with top, by squeezing top and bottom together 6. Insert and tighten screw. ___________________________________________________________________________________________ High Tech Pet Products, Inc. www.hightechpet.
REPLACING THE MS-5 BATTERY WATER RESISTANCE The High Tech MS-4 ultrasonic transmitter collar is water resistant meaning that rainy weather and humidity will not damage the unit. These collars are NOT designed to be fully immersed in water. Should this occur, simply open the unit, shake out water and let dry. In most cases the unit will function normally. However the life of the battery will likely be reduced or the battery may require replacement. The MS-5 collar is fully waterproof to a 3 foot depth.
MANY CONVENIENT ACCESSORIES! We’ve added all sorts of great new options to make your POWER PET PX the most versatile pet door you’ll find. W ER P ET D O Y SO PO EXTRA PET COLLARS: A RD Model MS-4 or MS-5 Ultrasonic Transmitter Collar You may wish to purchase an Extra collar for each additional pet and keep one or two more as spares. Lightweight and comfortable on all cats and dogs.
Wall Adapter Tunnel: Install your POWER PETTM door on any wall in one easy step with our convenient WALL ADAPTER TUNNEL accessory which extends the passageway and provides a sealed professional installation. It fits snugly into the POWER PETTM door main frame on one side of the wall, and the POWER PETTM outside frame on the other side. Adapts to any wall thickness from 4” to 8” thick.
ND B A R RIE R R A A R RIE DB R NE CONTA HU M YA SO U TOTAL PET CONTROL ACCESSORIES: RA DIO M AT IN SOUND BARRIER Model SBR-1 Indoor Sonic alarm keeps your pet off furniture, away from the kitchen table or out of an entire room. Operated from your pet’s MS-4 or MS-5 transmitter included with your POWER PET Door. Also, operated by the optional RC-7000X collar. Order one for each pet restricted area.
TROUBLESHOOTING GUIDE For each problem, start with 1st solution, then 2nd, etc., until solved.
If replacing an internal component, here are the workings of the door you will see after removing the back of the door frame.
ORDER INFORMATION To order extra collars and accessories please visit our website at www.hightechpet.com or call 1 (800) 255-1279 High Tech Pet Products, Inc. 2476 Palma Drive, Suite A Ventura, CA 93003 www.hightechpet.com Rev.
