Network Video Recorder User Manual UD.
User Manual of DS-7600NI Series NVR Hikvision® Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision).
User Manual of DS-7600NI Series NVR Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
User Manual of DS-7600NI Series NVR Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • • • • • Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf.
User Manual of DS-7600NI Series NVR Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to the models listed in the following table.
User Manual of DS-7600NI Series NVR Product Key Features General Connectable to network cameras, network dome and encoders. Connectable to the third-party network cameras like AXIS, Brickcom, Bosch, PANASONIC, SAMSUNG and SANYO, and network cameras that adopt ONVIF or PSIA protocol. PAL/NTSC adaptive video inputs. Each channel supports dual-stream. Up to 16 network cameras can be connected.
User Manual of DS-7600NI Series NVR Zooming in when playback. Reverse playback of multi-channel. Supports pause, play reverse, speed up, speed down, skip forward, and skip backward when playback, and locating by dragging the mouse. Up to 8-ch synchronous playback at 4CIF real time. Backup Export video data by USB or SATA device. Export video clips when playback. Management and maintenance of backup devices. Alarm and Exception Configurable arming time of alarm input/output.
User Manual of DS-7600NI Series NVR RS-485 transparent channel transmission. Alarm and exception information can be sent to the remote host. Remotely start/stop recording. Remotely start/stop alarm output. Remote PTZ control. Two-way audio and voice broadcasting. Embedded WEB server. Development Scalability: SDK for Windows and Linux system. Source code of application software for demo. Development support and training for application system.
User Manual of DS-7600NI Series NVR TABLE OF CONTENTS Product Key Features .............................................................................................................................. 6 Chapter 1Introduction ................................................................................................................................... 13 1.1 Front Panel ....................................................................................................................................
User Manual of DS-7600NI Series NVR 5.5 Manual Record .............................................................................................................................. 66 5.6 Configuring Holiday Record ......................................................................................................... 67 5.7 Configuring Redundant Recording ................................................................................................ 69 5.8 Configuring HDD Group for Recording ....
User Manual of DS-7600NI Series NVR 9.2.9 Configuring HTTPS Port .......................................................................................... 130 9.2.10 Configuring Email .................................................................................................... 131 9.2.11 Configuring UPnP™ ................................................................................................. 132 9.2.12 Configuring High-speed Download ................................................
User Manual of DS-7600NI Series NVR 13.4.2 Deleting a User ......................................................................................................... 176 13.4.3 Editing a User ........................................................................................................... 176 Appendix ..................................................................................................................................................... 178 Glossary ................................
User Manual of DS-7600NI Series NVR Chapter 1 Introduction 13
User Manual of DS-7600NI Series NVR 1.1 Front Panel Figure 1. 1 DS-7600NI-SE(/N) and DS-7600NI-SE/P Table 1. 1 Description of Front Panel No. Name Description Power 1 Status Indicator Status Tx/Rx Power indicator turns yellow when system is running. Status indicator blinks red when data is being read from or written to HDD. TX/RX indictor blinks yellow when network connection is functioning properly.
User Manual of DS-7600NI Series NVR 1.2 IR Remote Control Operations The NVR may also be controlled with the included IR remote control (not supported with the DS-7600NI-V and DS-7600NI-VP series NVR), shown in Figure 1. 3. Note: Batteries (2×AAA) must be installed before operation. Figure 1. 3 Remote Control Table 1. 3 Description of the Soft Keyboard Icons No. Name Description 1 POWER Power on/off the device. 2 DEV Enables/Disables Remote Control.
User Manual of DS-7600NI Series NVR alphabet, symbols and numeric input). 6 REC Button Enter the Manual Record setting menu. In PTZ control settings, press the button and then you can call a PTZ preset by pressing Numeric button. It is also used to turn audio on/off in the Playback mode. 7 PLAY Button The button is used to enter the All-day Playback mode. It is also used to auto scan in the PTZ Control menu. 8 INFO Button Reserved. 9 VOIP Button Switch between main and spot output.
User Manual of DS-7600NI Series NVR 1. Go to Menu > Settings > General > More Settings by operating the front control panel or the mouse. 2. Check and remember NVR ID#. The default ID# is 255. This ID# is valid for all the IR remote controls. 3. Press the DEV button on the remote control. 4. Enter the NVR ID# you set in step 2. 5. Press the ENTER button on the remote. If the Status indicator on the front panel turns blue, the remote control is operating properly.
User Manual of DS-7600NI Series NVR 1.3 USB Mouse Operation A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse: 1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR. 2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible reason may be that the two devices are not compatible, please refer to the recommended the device list from your provider.
User Manual of DS-7600NI Series NVR 1.4 Input Method Description Figure 1. 4 Soft Keyboard Description of the buttons on the soft keyboard: Table 1.
User Manual of DS-7600NI Series NVR 1.5 Rear Panel Figure 1. 5 DS-7604&7608NI-SE Figure 1. 6 DS-7604NI-SE/N Figure 1. 7 DS-7608&7616NI-SE/N Table 1. 6 Description of Rear Panel Interfaces No. Item Description 1 LAN Interfaces Connector for LAN (Local Area Network). 2 RS-485 Interface Connector for RS-485 devices. 3 Power Supply 12VDC power supply. 4 Power Switch Switch for turning on/off the device. 5 USB Connects USB disks and devices.
User Manual of DS-7600NI Series NVR Figure 1. 8 DS-7604&7608NI-SE/P Figure 1. 9 DS-7616NI-SE/P No. Item Description 1 LAN Network Interface Connector for LAN (Local Area Network). 2 RS-485 Interface Connects to RS-485 devices. 3 Power Supply 100~240VAC power supply 4 Power Switch Switch for turning on/off the device. Universal Serial Bus (USB) ports for additional devices such as USB 5 USB Interface 6 GND Ground (needs to be connected when NVR starts up).
User Manual of DS-7600NI Series NVR 2 LAN Network Interface Connector for LAN (Local Area Network). 3 Audio In RCA connector for voice talk input 4 GND Ground (needs to be connected when NVR starts up). 5 Audio Out RCA connector for audio output 6 HDMI Interface HDMI video output connector. 7 VGA Output DB9 connector for VGA output. Display local video output and menu.
User Manual of DS-7600NI Series NVR Chapter 2 Getting Started 23
User Manual of DS-7600NI Series NVR 2.1 Starting Up and Shutting Down the NVR Purpose: Proper startup and shutdown procedures are crucial to expanding the life of the NVR. Before you start: Check that the voltage of the extra power supply is the same with the NVR’s requirement, and the ground connection is working properly. Starting up the NVR: Steps: 1. Check the power supply is plugged into an electrical outlet.
User Manual of DS-7600NI Series NVR Rebooting the NVR In the Shutdown menu, you can also reboot the NVR. Steps: 1. Enter the Shutdown menu by clicking Menu > Shutdown. 2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR.
User Manual of DS-7600NI Series NVR 2.2 Using the Wizard for basic configuration By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below. Figure 2. 3 Start Wizard Interface Operating the Setup Wizard: 1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the Setup Wizard at that moment, click the Exit button.
User Manual of DS-7600NI Series NVR Figure 2. 5 Date and Time Settings 6. After the time settings, click Next button which takes you back to the Network Setup Wizard window, as shown in Figure 2. 6. DS-7604&7608&7616NI-SE and DS-7600NI-V DS-7600NI-SE/N, DS-7600NI-SE/P and DS-7600NI-VP Figure 2.
User Manual of DS-7600NI Series NVR Note: For DS-7600NI-SE/N, DS-7600NI-SE/P and DS-7600NI-VP series NVR, the internal NIC IPv4 address should be configured for the cameras connecting to the PoE network interfaces of the NVR. 7. Click Next button after you configured the network parameters, which takes you to the HDD Management window, shown in Figure 2. 7. Figure 2. 7 HDD Management 8. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD. 9.
User Manual of DS-7600NI Series NVR Figure 2. 9 Record Settings 12. Click Copy to copy the settings to other channels, as shown in Figure 2. 10. Figure 2. 10 Copy Record Settings 13. Click OK to complete the startup Setup Wizard.
User Manual of DS-7600NI Series NVR 2.3 Adding and Connecting the IP Cameras 2.3.1 Adding the Online IP Cameras Purpose: The main function of the NVR is to connect the network cameras and record the video got from it. So before you can get a live view or record of the video, you should add the network cameras to the connection list of the device. Before you start: Ensure the network connection is valid and correct.
User Manual of DS-7600NI Series NVR manually. • Manual Steps: 1. To add the online cameras with same network segment: 1) The detected online camera will be listed in the camera list, as shown in the figure below. Figure 2. 13 Manual Adding IP Camera Interface 2) Click the button to add the camera. Explanation of the icons: Icon Explanation Icon Explanation Edit basic parameters of the camera Add the detected IP camera.
User Manual of DS-7600NI Series NVR be added. 3) • Click Add to add the camera. OPTION 2: Steps: 1. Enter the Camera Management interface. Menu> Camera> Camera Figure 2. 15 Main Menu 2. Repeat the step 1 and 2 of adding IP cameras manually to add the camera. Figure 2. 16 IP Camera Management Interface 3. (For the encoders with multiple channels only) check the checkbox of Channel No. in the pop-up window, as shown in the following figure, and click OK to finish adding.
User Manual of DS-7600NI Series NVR Figure 2. 17 Selecting Multiple Channels 2.3.2 Editing the Connected IP cameras and Configuring Customized Protocols After the adding of the IP cameras, the basic information of the camera lists in the page, you can configure the basic setting of the IP cameras. Steps: 1. Click the icon to edit the parameters; you can edit the IP address, protocol and other parameters. Figure 2. 18 Edit the Parameters 2. Click OK to save the settings and exit the editing interface.
User Manual of DS-7600NI Series NVR Figure 2. 19 Network Configuration of the Camera 2. You can edit the network information and the password of the camera. Figure 2. 20 Password Configuration of the Camera 3. Click Apply to save the settings and click OK to exit the interface. Configuring the customized protocols Purpose: To connect the network cameras which are not configured with the standard protocols, you can configure the customized protocols for them. Steps: 1.
User Manual of DS-7600NI Series NVR Figure 2. 21 Protocol Management Interface There are 16 customized protocols provided in the system, you can edit the protocol name; and choose whether to enable the sub-stream. 2. Choose the protocol type of transmission and choose the transfer protocols. Note: The protocol type and the transfer protocols must be supported by the connected network camera.
User Manual of DS-7600NI Series NVR network cameras directly; and if you disable the PoE interface, you can also connect to the online network cameras. And the PoE interface supports the Plug-and-Play function. Example: As for 7604NI-SE/P NVR, when you want to connect 1 online camera and connect 3 network cameras via PoE interfaces, you must disable 1 PoE interface in the Edit IP camera panel.
User Manual of DS-7600NI Series NVR Figure 2. 25 Edit IP Camera Interface - Manual 3. Click the Apply button to finish adding. 2.3.4 Editing IP cameras connected to the built-in switch network interfaces (Only for DS-7600NI-SE/N series NVR) For DS-7600NI-SE/N series NVR, the extra network interfaces provide a built-in switch with plug-and-play function.
User Manual of DS-7600NI Series NVR 2. Click the • button, and select the Adding Method in the drop-down list. Plug-and-Play: It means that the camera is connected to the built-in switch interface, so in this case, the parameters of the camera can’t be edited. The IP address of the camera can only be edited in the Network Configuration interface, see Chapter 9.1 Configuring General Settings for detailed information. Figure 2.
User Manual of DS-7600NI Series NVR Chapter 3 Live View 39
User Manual of DS-7600NI Series NVR 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live View mode when powered on. Live View Icons In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are alarms occur as soon as possible. Table 3.
User Manual of DS-7600NI Series NVR 3.2 Operations in Live View Mode In live view mode, there are many functions provided. The functions are listed below. • • • Single Screen: showing only one screen on the monitor. Multi-screen: showing multiple screens on the monitor simultaneously. Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on the configuration menu before enabling the auto-switch. Menu>Configuration>Live View>General.
User Manual of DS-7600NI Series NVR Figure 3. 1 Right-click Menu 3.2.2 Quick Setting Toolbar in Live View Mode On the screen of each channel, there is a quick setting toolbar which shows when you single click the mouse in the corresponding screen. Figure 3. 2 Quick Setting Toolbar Table 3.
User Manual of DS-7600NI Series NVR Figure 3. 3 Digital Zoom Image Settings icon can be selected to enter the Image Settings menu. You can set the image parameters like brightness, contrast, saturation and hue. Figure 3. 4 Image Settings- Customize Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency. Figure 3.
User Manual of DS-7600NI Series NVR 3.3 Adjusting Live View Settings Purpose: Live View settings can be customized according to different needs. You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc. Steps: 1. Enter the Live View Settings interface. Menu> Configuration> Live View Figure 3.
User Manual of DS-7600NI Series NVR 2) Select the small window, and double-click on the channel number to display the channel on the window. You can click button to start live view for all the channels and click view. 3) Click the Apply button to save the setting.
User Manual of DS-7600NI Series NVR 3.4 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter user name and password tog in again. Steps: 1. Enter the Shutdown menu. Menu>Shutdown Figure 3. 8 Shutdown 2. Click Logout. Note: After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system.
User Manual of DS-7600NI Series NVR Chapter 4 PTZ Controls 47
User Manual of DS-7600NI Series NVR 4.1 Configuring PTZ Settings Purpose: Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you control the PTZ camera. Steps: 1. Enter the PTZ Settings interface. Menu >Camera> PTZ Figure 4. 1 PTZ- General 2. Choose the camera for PTZ setting in the Camera dropdown list. 3. Enter the parameters of the PTZ camera. Note: All the parameters should be exactly the same as the PTZ camera parameters.
User Manual of DS-7600NI Series NVR 4.2 Setting PTZ Presets, Patrols & Patterns Before you start: Please make sure that the presets, patrols and patterns should be supported by PTZ protocols. 4.2.1 Customizing Presets Purpose: Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place. Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings Figure 4. 2 PTZ- More Settings 2.
User Manual of DS-7600NI Series NVR 4.2.2 Calling Presets Purpose: This feature enables the camera to point to a specified position such as a window when an event takes place. Call preset in the PTZ setting interface: Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Check the round icon of Call Preset. Figure 4. 4 PTZ- Call Preset 3. Choose the preset number. Call preset in live view mode: Steps: 1.
User Manual of DS-7600NI Series NVR 2. Choose Camera in the list on the menu. 3. Double click the preset in the Preset list to call it. 4.2.3 Customizing Patrols Purpose: Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps above in Customizing Presets. Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2.
User Manual of DS-7600NI Series NVR Repeat the above steps to add more key points. Click the points. icon to delete the corresponding key point, and click the trash icon Select a key point, then click or to.delete all the key button to adjust the order of the key points. Figure 4. 8 Key Points Deletion 4.2.4 Calling Patrols Purpose: Calling a patrol makes the PTZ to move according the predefined patrol path. Calling patrol in the PTZ setting interface: Steps: 1. In the PTZ setting interface.
User Manual of DS-7600NI Series NVR Figure 4. 9 PTZ Toolbar- Patrol 4.2.5 Customizing Patterns Purpose: Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement according to the predefined path. Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Choose pattern number in the option box. Figure 4. 10 PTZ- Pattern 3.
User Manual of DS-7600NI Series NVR 4. Click to save the pattern. 4.2.6 Calling Patterns Purpose: Follow the procedure to move the PTZ camera according to the predefined patterns. Calling pattern in the PTZ setting interface Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Select the pattern number. 3. Click , then the PTZ moves according to the pattern. Click to stop it. Call pattern in live view mode Steps: 1.
User Manual of DS-7600NI Series NVR 4.3 PTZ Control Toolbar In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or choose the PTZ Control icon to enter the PTZ toolbar. Figure 4. 12 PTZ Toolbar Table 4.
User Manual of DS-7600NI Series NVR Chapter 5 Record Settings 56
User Manual of DS-7600NI Series NVR 5.1 Configuring Recording Parameters Purpose: By configuring the recording parameters you can define the parameters which affect the image quality, such as the transmission stream type, the resolution and so on. Before you start: 1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu>HDD>General) Figure 5. 1 HDD- General 2. Check the storage mode of the HDD 1) Click Advanced to check the storage mode of the HDD.
User Manual of DS-7600NI Series NVR 2. Parameters Setting for Recording 1) Select Record tab page to configure. You can configure the stream type, the resolution, and other parameters on your demand. • Pre-record: The time you set to record before the scheduled time or event. For example, when an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records it at 9:59:55. • Post-record: The time you set to record after the event or the scheduled time.
User Manual of DS-7600NI Series NVR 5.2 Configuring Record Schedule Purpose: Set the record schedule, and then the camera automatically starts/stops recording according to the configured schedule. Steps: 1. Enter the Record Schedule interface. Menu>Record>Schedule 2. Configure Record Schedule 1) Select Record Schedule. Figure 5. 5 Record Schedule 2) Choose the camera you want to configure. 3) Select the check box after the Enable Schedule item.
User Manual of DS-7600NI Series NVR Figure 5. 7 Edit Schedule III. To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other. Repeat the above edit schedule steps to schedule recording for other days in the week. If the schedule can also be applied to other days, click Copy. Figure 5. 8 Copy Schedule to Other Days IV. V.
User Manual of DS-7600NI Series NVR Figure 5. 10 Descriptions of the color icons Click the Apply button to validate the settings. If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy. Figure 5.
User Manual of DS-7600NI Series NVR 5.3 Configuring Motion Detection Record Purpose: Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center and so on.
User Manual of DS-7600NI Series NVR Figure 5. 14 Motion Detection Setting 5) Select the channels which you want the motion detection event to trigger recording. 6) Click Apply to save the settings. 7) Click OK to back to the upper level menu. 8) Exit the Motion Detection menu. 3. Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see Chapter Configuring Record Schedule.
User Manual of DS-7600NI Series NVR 5.4 Configuring Alarm Triggered Record Purpose: Follow the procedure to configure alarm triggered recording. Steps: 1. Enter the Alarm setting interface. Menu> Configuration> Alarm Figure 5. 15 Alarm Settings 2. Click the Alarm Input tab. Figure 5. 16 Alarm Settings- Alarm Input 1) Select Alarm Input number and configure alarm parameters. 2) Choose N.O (normally open) or N.C (normally closed) for alarm type. 3) Check the checkbox of Enable. 4) Click Settings.
User Manual of DS-7600NI Series NVR Figure 5. 17 Alarm Settings 5) Choose the alarm triggered recording channel. 6) Check the checkbox to select channel. 7) Click Apply to save settings. 8) Click OK to back to the upper level menu. Repeat the above steps to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number. Figure 5. 18 Copy Alarm Input 3.
User Manual of DS-7600NI Series NVR 5.5 Manual Record Purpose: Follow the steps to set parameters for the manual record. The manual recording is prior to the scheduled recording. Steps: 1. Enter the Manual settings interface. Menu> Manual Or press the REC button on the remote control. Figure 5. 19 Manual Record 2. Enabling Manual Record 1) Select Record on the left bar. 2) Click the status button before camera number to change 3. to . Disable manual record.
User Manual of DS-7600NI Series NVR 5.6 Configuring Holiday Record Purpose: Follow the steps to configure the record schedule on holiday for that year. You may want to have different plan for recording on holiday. Steps: 1. Enter the Record setting interface. Menu>Record> Holiday Figure 5. 20 Holiday Settings 2. Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure 5. 21 Edit Holiday Settings 2) Check the checkbox after Enable Holiday.
User Manual of DS-7600NI Series NVR 3) Select Mode from the dropdown list. There are three different modes for the date format to configure holiday schedule. 3. 4) Set the start and end date. 5) Click Apply to save settings. 6) Click OK to exit the Edit interface. Enter Record Schedule settings interface to edit the holiday recording schedule. See Chapter 6.2 Configuring Record Schedule.
User Manual of DS-7600NI Series NVR 5.7 Configuring Redundant Recording Purpose: Enabling redundant recording, which means saving the record files not only in the R/W HDD but also in the redundant HDD, will effectively enhance the data safety and reliability. . Steps: 1. Enter HDD Information interface. Menu> HDD Figure 5. 22 HDD General 2. Select the HDD and click 1) to enter the Local HDD Settings interface. Set the HDD property to Redundancy. Figure 5.
User Manual of DS-7600NI Series NVR Figure 5. 24 Record Parameters 2) Select Camera you want to configure in the drop-down list. 3) Check the checkbox of Redundant Record. 4) Click Apply to save settings and back to the upper level menu. Repeat the above steps for configuring other channels.
User Manual of DS-7600NI Series NVR 5.8 Configuring HDD Group for Recording Purpose: You can group the HDDs and save the record files in certain HDD group. Steps: 1. Enter HDD setting interface. Menu>HDD Figure 5. 25 HDD General 2. Select Advanced on the left bar. Figure 5. 26 Storage Mode Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information, please refer to Chapter 12.4 Managing HDD Group. 3. Select General in the left bar. 4. Configuring HDD group.
User Manual of DS-7600NI Series NVR 5.9 Files Protection Purpose: You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten. Protect file by locking the record files: Steps: 1. Enter Playback setting interface. Menu> Playback Figure 5. 27 Playback 2. Select the channels you want to investigate by checking the checkbox to 3. Configure the record type, file type start/end time. 4. Click Search to show the results. . Figure 5.
User Manual of DS-7600NI Series NVR Figure 5. 29 Unlocking Attention Protect file by setting HDD property to Read-only Steps: 1. Enter HDD setting interface. Menu> HDD Figure 5. 30 HDD General 2. Click to edit the HDD you want to protect. Figure 5. 31 HDD General- Editing Note: To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter Managing HDD Group. 3. Set the HDD property to Read-only. 4. Click OK to save settings and back to the upper level menu. Notes: 1.
User Manual of DS-7600NI Series NVR Chapter 6 Playback 74
User Manual of DS-7600NI Series NVR 6.1 Playing Back Record Files 6.1.1 Playing Back by Channel Purpose: Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. OPTION 1: Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar. Note: In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6.
User Manual of DS-7600NI Series NVR The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in Figure 6. 3. Figure 6. 3 Playback Interface Click the channel(s) to execute simultaneous playback of multiple channels. Figure 6. 4 Toolbar of Playback Note: The indicates the start/end time of the record. Table 6.
User Manual of DS-7600NI Series NVR 6.1.2 Playing Back by Time Purpose: Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. Steps: 1. Enter playback interface. Menu>Playback 2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar. Figure 6.
User Manual of DS-7600NI Series NVR Note: The indicates the start/end time of the record. Table 6.
User Manual of DS-7600NI Series NVR Figure 6. 8 Alarm Input Search Interface Figure 6. 9 Motion Search Interface 4. Click Search button to get the search result information. You may refer to the right-side bar for the result.
User Manual of DS-7600NI Series NVR Figure 6. 10 Search Result Bar(Alarm In and Motion) 5. Click button to play back the file. Notes: 1. Pre-play and post-play can be configured. 2. If the event is set to trigger the recording of multiple channels, clicking the Playback interface. You can select the channels to play back synchronously. You can click the Back button to back to the search interface. 6. Playback interface.
User Manual of DS-7600NI Series NVR Figure 6. 12 Toolbar of Playback by Event Table 6.
User Manual of DS-7600NI Series NVR Figure 6. 13 Interface of Playback by Time Click button to add default tag. Click button to add customized tag and input tag name. Note: Max. 64 tags can be added to a single video file. 3. Tag management. Click button to check, edit and delete tag(s). Figure 6. 14 Tag Management Interface Steps: 1. Select the Tag from the drop-down list in the Playback interface. 2.
User Manual of DS-7600NI Series NVR Figure 6. 15 Video Search by Tag 3. Click button to play back the file. You can click the Back button to back to the search interface. Note: Pre-play and post-play can be configured. Figure 6. 16 Interface of Playback by Tag Figure 6.
User Manual of DS-7600NI Series NVR Table 6.
User Manual of DS-7600NI Series NVR Figure 6. 19 Result of System Log Search 4. Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6. 20 Interface of Playback by Log 6.1.6 Playing Back External File Purpose: Perform the following steps to look up and play back files in the external devices. Steps: 1. Enter Tag Search interface. Menu>Playback 2. Select the External File in the drop-down list on the top-left side.
User Manual of DS-7600NI Series NVR Figure 6.
User Manual of DS-7600NI Series NVR 6.2 Auxiliary Functions of Playback 6.2.1 Playing Back Frame by Frame Purpose: Play video files frame by frame, in case of checking image details of the video when abnormal events happen. Steps: Go to Playback interface. If you choose playback of the record file: click button until the speed changes to Single frame and one click on the playback screen represents playback of one frame.
User Manual of DS-7600NI Series NVR Figure 6. 22 Interface of Playback by Time 2. Click the on the playback control toolbar to enter Smart Search mode. 3. Click and drag the mouse to draw area(s). You can click button area. After drawing area(s), click button to set the full screen as target searching to execute smart search in this area. Note: Multi-area and full-screen searching modes are supported. Figure 6.
User Manual of DS-7600NI Series NVR Figure 6. 24 Smart Search Result Figure 6. 25 Toolbar of Smart Search Playback Note: The indicates the start/end time of the record. Table 6.
User Manual of DS-7600NI Series NVR 6.2.3 Digital Zoom Steps: 1. Click the button on the playback control bar to enter Digital Zoom interface. 2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times. Figure 6. 26 Draw Area for Digital Zoom 3. Right-click the image to exit the digital zoom interface. 6.2.4 Reverse Playback of Multi-channel Purpose: You can play back record files of multi-channel reversely.
User Manual of DS-7600NI Series NVR Figure 6. 27 4-ch Synchronous Playback Interface 3. Click to play back the record files reversely.
User Manual of DS-7600NI Series NVR Chapter 7 Backup 92
User Manual of DS-7600NI Series NVR 7.1 Backing up Record Files 7.1.1 Quick Export Purpose: Export record files to backup device(s) quickly. Steps: 1. Enter Video Export interface. Menu>Export>Normal Choose the channel(s) you want to back up and click Quick Export button. Note: 1) The time duration of record files on a specified channel cannot exceed one day. Otherwise, the message box “Max. 24 hours are allowed for quick export.” will pop up.
User Manual of DS-7600NI Series NVR Stay in the Exporting interface until all record files are exported. Figure 7. 3 Export Finished 3. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 4 Checkup of Quick Export Result Using USB1-1 7.1.
User Manual of DS-7600NI Series NVR Figure 7. 5 Normal Video Search for Backup 3. Select record files you want to back up. Click to play the record file if you want to check it. Check the checkbox before the record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 6 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup.
User Manual of DS-7600NI Series NVR Figure 7. 7 Export by Normal Video Search using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”. Figure 7. 8 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-7600NI Series NVR Backup using USB writer and SATA writer Steps: 1. Enter Export interface. Menu>Export>Normal 2. Set search condition and click Search button to enter the search result interface. Figure 7. 10 Normal Video Search for Backup 3. Select record files you want to back up. Click button to play the record file if you want to check it. Check the checkbox before the record files you want to back up.
User Manual of DS-7600NI Series NVR Figure 7. 12 Export by Normal Video Search using USB Writer Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”. Figure 7. 13 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-7600NI Series NVR 7.1.3 Backing up by Event Search Purpose: Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), or SATA writer. Quick Backup and Normal Backup are supported. Steps: 1. Enter Export interface. Menu>Export>Event 1) Select “Alarm Input” from the dropdown list of Event Type. Note: Event types contain Alarm Input and Motion, here we take the backing up by alarm input as an example. 2) Select the alarm input No. and time. Figure 7.
User Manual of DS-7600NI Series NVR Figure 7. 17 Event Details Interface 4. Export. Click the Export button and start back up. Note: If the inserted USB device is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure 7. 18 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”.
User Manual of DS-7600NI Series NVR Figure 7. 19 Export Finished 5. Check backup result. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 20 Checkup of Event Export Result Using USB Flash Drive 7.1.4 Backing up Video Clips Purpose: You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer) or SATA writer. Steps: 1. Enter Playback interface. Please refer to Chapter 6.
User Manual of DS-7600NI Series NVR Figure 7. 21 Interface of Playback by Time 4. Click Yes to save video clips and enter Export interface, or click No to quit and do not save video clips. Figure 7. 22 Attention to Video Clip Saving 5. Export. Click Export button and start backup. Note: If the inserted USB device is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure 7.
User Manual of DS-7600NI Series NVR Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 24 Export Finished 6. Check backup result. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 25 Checkup of Video Clips Export Result Using USB Flash Drive 7.2 Managing Backup Devices Management of USB flash drives and USB HDDs. 1. Enter Search Result interface of record files.
User Manual of DS-7600NI Series NVR 2. Select record files you want to back up. Click Export button to enter Export interface. Note: At least one record file shall be selected. Figure 7. 27 Result of Normal Video Search for Backup 3. Backup device management. Click New Folder button if you want to create a new folder in the backup device. Select a record file or folder in the backup device and click Select a record file in the backup device and click button if you want to delete it. button to play it.
User Manual of DS-7600NI Series NVR Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. Note: At least one channel shall be selected. Figure 7. 29 Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface. Note: At least one record file shall be selected. Figure 7. 30 Result of Normal Video Search for Backup 3. Backup device management.
User Manual of DS-7600NI Series NVR Figure 7.
User Manual of DS-7600NI Series NVR Chapter 8 Alarm Settings 107
User Manual of DS-7600NI Series NVR 8.1 Setting Motion Detection Alarm Steps: 1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection. Menu> Camera> Motion Figure 8. 1 Motion Detection Setup Interface 2. Set up detection area and sensitivity. Tick “Enable Motion Detection”, use the mouse to draw detection area(s) and drag the sensitivity bar to set sensitivity. Click button and set alarm response actions. 3.
User Manual of DS-7600NI Series NVR Figure 8. 3 Set Arming Schedule of Motion Detection 5. Click Linkage Action tab to set up alarm response actions of motion alarm (please refer to Chapter Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 6. Click the OK button to complete the motion detection settings of the channel.
User Manual of DS-7600NI Series NVR 8.2 Setting Sensor Alarms Purpose: Set parameters and handling action of an external sensor alarm. Steps: 1. Enter Alarm Settings of System Configuration and select an alarm input. Menu> Configuration> Alarm Select Alarm Input tab to enter Alarm Input Settings interface. Figure 8. 4 Alarm Status Interface of System Configuration 2. Set up the handling action of the selected alarm input. Check the Enable checkbox and click button to set up its alarm response actions.
User Manual of DS-7600NI Series NVR Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. Figure 8. 6 Set Arming Schedule of Alarm Input 6. If necessary, select PTZ Linking tab and set PTZ linkage of the alarm input. Set PTZ linking parameters and click OK to complete the settings of the alarm input. Note: Please check whether the PTZ or speed dome supports PTZ linkage.
User Manual of DS-7600NI Series NVR Figure 8.
User Manual of DS-7600NI Series NVR 8.3 Detecting Video Loss Alarm Purpose: Detect video loss of a channel and take alarm response action(s). Steps: 1. Enter Video Loss interface of Camera Management and select a channel you want to detect. Menu> Camera> Video Loss Figure 8. 9 Video Loss Setup Interface 2. Set up handling method of video loss. Check the checkbox of “Enable Video Loss Alarm”, and click button to set up handling action of video loss. 3. Set up arming schedule of the channel.
User Manual of DS-7600NI Series NVR Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5. Click the OK button to complete the video loss settings of the channel.
User Manual of DS-7600NI Series NVR 8.4 Detecting Video Tampering Alarm Purpose: Trigger alarm when the lens is covered and take alarm response action(s). Steps: 1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video tampering. Menu> Camera> Video Tampering Figure 8. 11 Video Tampering Setup Interface 2. Set the video tampering handling method of the channel. Check the checkbox of “Enable Video Tampering”.
User Manual of DS-7600NI Series NVR Figure 8. 13 Set Arming Schedule of Video Tampering 4. Select Linkage Action tab to set up alarm response actions of video tampering alarm (please refer to Chapter Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5. Click the OK button to complete the video tampering settings of the channel.
User Manual of DS-7600NI Series NVR 8.5 Handling Exceptions Alarm Purpose: Exception settings refer to the handling method of various exceptions, e.g. • • • • • • HDD Full: The HDD is full. HDD Error: Writing HDD error or unformatted HDD. Network Disconnected: Disconnected network cable. IP Conflicted: Duplicated IP address. Illegal Login: Incorrect user ID or password. Record Exception: No space for saving recorded files.
User Manual of DS-7600NI Series NVR 8.6 Setting Alarm Response Actions Purpose: Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Trigger Alarm Output and Send Email. Full Screen Monitoring When an alarm is triggered, the local monitor (VGA or HDMI monitor) display in full screen the video image from the alarming channel configured for full screen monitoring.
User Manual of DS-7600NI Series NVR 2. Set up arming schedule of the alarm output. Choose one day of a week and up to 8 time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. Figure 8. 16 Set Arming Schedule of Alarm Output 3. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. Click the OK button to complete the video tampering settings of the alarm output No. 4.
User Manual of DS-7600NI Series NVR 8.7 Triggering or Clearing Alarm Output Manually Purpose: Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface. Steps: Select the alarm output you want to trigger or clear and make related operations. Menu> Manual> Alarm Click Trigger/Clear button if you want to trigger or clear an alarm output.
User Manual of DS-7600NI Series NVR Chapter 9 Network Settings 121
User Manual of DS-7600NI Series NVR 9.1 Configuring General Settings Purpose: Network settings must be properly configured before you operate NVR over network. Steps: 1. Enter the Network Settings interface. Menu >Configuration>Network 2. Select the General tab. DS-7604&7608&7616NI-SE and DS-7600NI-V DS-7600NI-SE/N, DS-7600NI-SE/P and DS-7600NI-VP Figure 9. 1 Network Settings Interface 3.
User Manual of DS-7600NI Series NVR 9.2 Configuring Advanced Settings 9.2.1 Configuring PPPoE Settings Purpose: Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 9. 2. Figure 9. 2 PPPoE Settings Interface 3. Check the PPPoE checkbox to enable this feature. 4.
User Manual of DS-7600NI Series NVR Figure 9. 3 DDNS Settings Interface 3. Check the DDNS checkbox to enable this feature. 4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and HiDDNS. • IPServer: Enter Server Address for IPServer. Figure 9. 4 IPServer Settings Interface • DynDNS: 1) Enter Server Address for DynDNS (i.e. members.dyndns.org). 2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website.
User Manual of DS-7600NI Series NVR 2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP website. Figure 9. 7 NO-IP Settings Interface • HiDDNS: Enter the Server Address and Device Domain Name for HiDDNS. 1) Enter the Server Address of the HiDDNS server, which is www.hik-online.com by default. 2) Enter the Device Domain Name.
User Manual of DS-7600NI Series NVR Figure 9. 9 Register an Account 3) In the Device Management interface, click to register the device. Figure 9. 10 Register the Device Note: The device name can only contain the lower-case English letter, numeric and ‘-’; and it must start with the lower-case English letter and cannot end with ‘-’.
User Manual of DS-7600NI Series NVR Figure 9. 11 Access Device via iVMS4200 5. Click Apply button to save and exit the interface. 9.2.3 Configuring NTP Server Purpose: A Network Time Protocol (NTP) Server can be configured on your NVR to ensure the accuracy of system date/time. Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the NTP tab to enter the NTP Settings interface, as shown in Figure 9. 12. Figure 9. 12 NTP Settings Interface 3.
User Manual of DS-7600NI Series NVR 9.2.4 Configuring SNMP Purpose: You can use SNMP protocol to get device status and parameters related information. Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the SNMP tab to enter the SNMP Settings interface, as shown in Figure 9. 13. Figure 9. 13 SNMP Settings Interface 3. Check the SNMP checkbox to enable this feature. 4. Configure the following SNMP settings: • Trap Address: IP Address of SNMP host.
User Manual of DS-7600NI Series NVR 3. Enter Alarm Host IP and Alarm Host Port in the text fields. The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance Software (e.g., iVMS-4200) is installed, and the Alarm Host Port must be the same as the alarm monitoring port configured in the software. Figure 9. 15 Configure Alarm Host 4. Click Apply button to save and exit the interface. 9.2.
User Manual of DS-7600NI Series NVR Figure 9. 17 RTSP Settings Interface 3. Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can change it according to different requirements. 4. Click Apply button to save and exit the menu. 9.2.8 Configuring Server and HTTP Ports Purpose: You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and the default HTTP port is 80. Steps: 1. Enter the Network Settings interface.
User Manual of DS-7600NI Series NVR Figure 9. 19 HTTPS Settings Menu 4. Enter the HTTPS Port. 5. Click the Apply button to save and exit the interface. 9.2.10 Configuring Email Purpose: The system can be configured to send an Email notification to all designated users if an alarm event is detected, etc., an alarm or motion event is detected or the administrator password is changed.
User Manual of DS-7600NI Series NVR Receiver: The name of user to be notified. Receiver’s Address: The Email address of user to be notified. Enable Attached Pictures: Check the checkbox of Enable Attached Picture if you want to send email with attached alarm images. The interval is the time of two adjacent alarm images. You can also set SMTP port and enable SSL here. Interval: The interval refers to the time between two actions of sending attached pictures.
User Manual of DS-7600NI Series NVR If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router automatically. Steps: 1) Click Apply button to save the settings. 2) You can click Refresh button to get the latest status of the port mapping. Figure 9. 23 UPnP™ Settings Finished-Auto Task2: Manual If you select Manual as the mapping type, you can edit the external port on your demand by clicking to activate the External Port Settings dialog box.
User Manual of DS-7600NI Series NVR Figure 9. 25 UPnP™ Settings Finished-Manual 9.2.12 Configuring High-speed Download Purpose: You can enable the High-speed Download function to widen the outgoing bandwidth of the device. In this way you can speed up the download of record files through IE browser or CMS software. Note: If you enable the high-speed download function, the local menu operation will be affected.
User Manual of DS-7600NI Series NVR 9.3 Checking Network Traffic Purpose: You can check the network traffic to obtain real-time information of NVR such as linking status, MTU, sending/receiving rate, etc. Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect Figure 9. 28 Network Traffic Interface 2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed every 1 second.
User Manual of DS-7600NI Series NVR 9.4 Configuring Network Detection Purpose: You can obtain network connecting status of NVR through the network detection function, including network delay, packet loss, etc. 9.4.1 Testing Network Delay and Packet Loss Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect 2. Click the Network Detection tab to enter the Network Detection menu, as shown in Figure 9. 29. Figure 9. 29 Network Detection Interface 3.
User Manual of DS-7600NI Series NVR the backup device, please check whether it is compatible with the NVR. You can format the backup device if the format is incorrect. Figure 9. 31 Export Network Packet 4. Click Export to start exporting. 5. After the exporting is complete, click OK to finish the packet export, as shown in 0. Figure 9. 32 Packet Export Attention Note: Up to 1M data can be exported each time. 9.4.
User Manual of DS-7600NI Series NVR If the network is normal the following message box pops out. Figure 9. 34 Network status checking result If the message box pops out with other information instead of this one, you can click Network button to show the quick setting interface of the network parameters. 9.4.4 Checking Network Statistics Purpose: You can check the network status to obtain the real-time information of NVR. Steps: 1. Enter the Network Detection interface. Menu>Maintenance>Net Detection 2.
User Manual of DS-7600NI Series NVR Chapter 10 HDD Management 139
User Manual of DS-7600NI Series NVR 10.1 Initializing HDDs Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR. Note: A message box pops up when the NVR starts up if there exits any uninitialized HDD. Figure 10. 1 Message Box of Uninitialized HDD Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD. Steps: 1. Enter the HDD Information interface. Menu > HDD> General Figure 10.
User Manual of DS-7600NI Series NVR Figure 10. 5 HDD Status Changes to Normal Note: Initializing the HDD will erase all data on it.
User Manual of DS-7600NI Series NVR 10.2 Managing Network HDD Purpose: You can add the allocated NAS or disk of IP SAN to NVR, and use it as network HDD. Steps: 1. Enter the HDD Information interface. Menu > HDD>General 2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 10. 6. Figure 10. 6 HDD Information Interface 3. Add the allocated NetHDD. 4. Select the type to NAS or IP SAN. 5. Configure the NAS or IP SAN settings.
User Manual of DS-7600NI Series NVR Figure 10. 7 Add NAS Disk • Add IP SAN: 1) Enter the NetHDD IP address in the text field. 2) Click the Search button to search the available IP SAN disks. 3) Select the IP SAN disk from the list shown below. 4) Click the OK button to add the selected IP SAN disk. Note: Up to 1 IP SAN disk can be added. Figure 10. 8 Add IP SAN Disk 6. After having successfully added the NAS or IP SAN disk, return to the HDD Information menu.
User Manual of DS-7600NI Series NVR 10.3 Managing HDD Group 10.3.1 Setting HDD Groups Purpose: Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Group, as shown in Figure 10. 10. Figure 10. 10 Storage Mode Interface 3. Click the Apply button and the following Attention box will pop up. Figure 10. 11 Attention for Reboot 4.
User Manual of DS-7600NI Series NVR Figure 10. 12 Local HDD Settings Interface 7. Select the Group number for the current HDD. Note: The default group No. for each HDD is 1. 8. Click the OK button to confirm the settings. Figure 10. 13 Confirm HDD Group Settings 9. In the pop-up Attention box, click the Yes button to finish the settings. 10.3.2 Setting HDD Property Purpose: The HDD property can be set to redundancy, read-only or read/write (R/W).
User Manual of DS-7600NI Series NVR Figure 10. 14 Set HDD Property 3. Set the HDD property to R/W, Read-only or Redundancy. 4. Click the OK button to save the settings and exit the interface. 5. In the HDD Information menu, the HDD property will be displayed in the list. Note: At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy, and there is one HDD with R/W property.
User Manual of DS-7600NI Series NVR 10.4 Configuring Quota Mode Purpose: Each camera can be configured with allocated quota for the storage of recorded files. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Quota, as shown in Figure 10. 15. Note: The NVR must be rebooted to enable the changes to take effect. Figure 10. 15 Storage Mode Settings Interface 3. Select a camera for which you want to configure quota. 4. Enter the storage capacity in the text fields of Max.
User Manual of DS-7600NI Series NVR Figure 10. 17 Copy Settings to Other Camera(s) 6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of IP Camera to select all cameras. 7. Click the OK button to finish the Copy settings and back to the Storage Mode interface. 8. Click the Apply button to apply the settings. Note: If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for record.
User Manual of DS-7600NI Series NVR 10.5 Checking HDD Status Purpose: You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface Steps: 1. Enter the HDD Information interface. Menu > HDD>General 2. Check the status of each HDD which is displayed on the list, as shown in Figure 10. 18. Figure 10. 18 View HDD Status (1) Note: If the status of HDD is Normal or Sleeping, it works normally.
User Manual of DS-7600NI Series NVR Figure 10.
User Manual of DS-7600NI Series NVR 10.6 HDD Detection Purpose: The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures. S.M.A.R.T. Settings Steps: 1. Enter the S.M.A.R.T Settings interface. Menu > HDD > HDD Detect. 2.
User Manual of DS-7600NI Series NVR 2. Select the HDD No. in the dropdown list you want to configure, and choose All Detection or Key Area Detection as the detection type. 3. Click the Detect button to start the detection Figure 10. 21 Bad Sector Detection And you can click Error info button to see the detailed damage information And you can also pause/resume or cancel the detection.
User Manual of DS-7600NI Series NVR 10.7 Configuring HDD Error Alarms Purpose: You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. Steps: 1. Enter the Exception interface. Menu > Configuration > Exceptions 2. Select the Exception Type to HDD Error from the dropdown list. 3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 10. 22.
User Manual of DS-7600NI Series NVR Chapter 11 Camera Settings 154
User Manual of DS-7600NI Series NVR 11.1 Configuring OSD Settings Purpose: You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc. Steps: 1. Enter the OSD Configuration interface. Menu > Camera > OSD 2. Select the camera to configure OSD settings. 3. Edit the Camera Name in the text field. 4. Configure the Display Name, Display Date and Display Week by clicking the checkbox. 5. Select the Date Format, Time Format and Display Mode. Figure 11.
User Manual of DS-7600NI Series NVR 11.2 Configuring Privacy Mask Purpose: You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy mask can prevent certain surveillance areas to be viewed or recorded. Steps: 1. Enter the Privacy Mask Settings interface. Menu > Camera >Privacy Mask 2. Select the camera to set privacy mask. 3. Click the checkbox of Enable Privacy Mask to enable this feature. Figure 11. 2 Privacy Mask Settings Interface 4.
User Manual of DS-7600NI Series NVR 11.3 Configuring Video Parameters Steps: 1. Enter the Image Settings interface. Menu > Camera >Image Figure 11. 4 Image Settings Interface 2. Select the camera to set image parameters. 3. You can click on the arrow to change the value of each parameter. 4. Click the Apply button to save the settings.
User Manual of DS-7600NI Series NVR Chapter 12 NVR Management Maintenance 158 and
User Manual of DS-7600NI Series NVR 12.1 Viewing System Information 12.1.1 Viewing Device Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. , firmware version and encode version, as shown in Figure 12. 1. Figure 12. 1 Device Information Interface 12.1.2 Viewing Camera Information Steps: 1. Enter the System Information interface.
User Manual of DS-7600NI Series NVR 12.1.4 Viewing Alarm Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure 12. 4. Figure 12. 4 Alarm Information Interface 12.1.5 Viewing Network Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2.
User Manual of DS-7600NI Series NVR 12.1.6 Viewing HDD Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc.. 12.2 Searching & Export Log Files Purpose: The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and exported at any time. Steps: 1. Enter the Log Search interface.
User Manual of DS-7600NI Series NVR Figure 12. 7 Log Search Results Note: Up to 2000 log files can be displayed each time. 5. You can click the button of each log or double click it to view its detailed information, as shown in Figure 12. 8. And you can also click the button to view the related video files if available. Figure 12. 8 Log Details 6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 12. 9.
User Manual of DS-7600NI Series NVR Figure 12. 9 Export Log Files 7. Select the backup device from the dropdown list of Device Name. 8. Click the Export to export the log files to the selected backup device. You can click the New Folder button to create new folder in the backup device, or click the Format button to format the backup device before log export. Notes: 1) Please connect the backup device to NVR before operating log export.
User Manual of DS-7600NI Series NVR Figure 12. 10 Log Export Interface You can check the checkbox of the HDD. Click the Export button to export all the log files stored in the HDD.
User Manual of DS-7600NI Series NVR 12.3 Importing/Exporting Configuration Files Purpose: The configuration files of the NVR can be exported to local device for backup; and the configuration files of one NVR can be imported to multiple NVR devices if they are to be configured with the same parameters. Steps: 1. Enter the Import/Export Configuration File interface. Menu > Maintenance >Import/Export Figure 12. 11 Import/Export Config File 2.
User Manual of DS-7600NI Series NVR 12.4 Upgrading System Purpose: The firmware on your NVR can be upgraded by local backup device or remote FTP server. 12.4.1 Upgrading by Local Backup Device Steps: 1. Connect your NVR with a local backup device where the update firmware file is located. 2. Enter the Upgrade interface. Menu >Maintenance>Upgrade 3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 12. 12. Figure 12. 12 Local Upgrade Interface 4.
User Manual of DS-7600NI Series NVR Figure 12. 13 FTP Upgrade Interface 3. Enter the FTP Server Address in the text field. 4. Click the Upgrade button to start upgrading. 5. After the upgrading is complete, reboot the NVR to activate the new firmware.
User Manual of DS-7600NI Series NVR 12.5 Restoring Default Settings Steps: 1. Enter the Default interface. Menu > Maintenance > Default Figure 12. 14 Restore Factory Default 2. Click the OK button to restore the default settings. Note: Except the network parameters (including IP address, subnet mask, gateway, MTU, default route and server port), all other parameters of the device will be restored to factory default settings.
User Manual of DS-7600NI Series NVR Chapter 13 Others 169
User Manual of DS-7600NI Series NVR 13.1 Configuring General Settings Purpose: You can configure the output resolution, system time, mouse pointer speed through the Menu > Configuration > General interface. Steps: 1. Enter the General Settings interface. Menu >Configuration> General 2. Select the General tab. Figure 13. 1 General Settings Interface 3. Configure the following settings: • Language: The default language used is English.
User Manual of DS-7600NI Series NVR 13.2 Configuring DST Settings Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Choose DST Settings tab. Figure 13. 2 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item. Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
User Manual of DS-7600NI Series NVR 13.3 Configuring More Settings for Device Parameters Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 13. 3. Figure 13. 3 More Settings Interface 3. Configure the following settings: • Device Name: Edit the name of NVR. • Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the default No. is 255.
User Manual of DS-7600NI Series NVR 13.4 Managing User Accounts Purpose: There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is 12345. The Administrator has the permission to add and delete user and configure user parameters. 13.4.1 Adding a User Steps: 1. Enter the User Management interface. Menu >Configuration>User Figure 13. 4 User Management Interface 2. Click the Add button to enter the Add User interface.
User Manual of DS-7600NI Series NVR Figure 13. 5 Add User Menu 3. Enter the information for new user, including User Name, Password, Level and User’s MAC Address. Level: Set the user level to Operator or Guest. Different user levels have different operating permission. • Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all operating permission in Camera Configuration.
User Manual of DS-7600NI Series NVR Figure 13. 7 User Permission Settings Interface 6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for the user. Local Configuration • Local Log Search: Searching and viewing logs and system information of NVR. • Local Parameters Settings: Configuring parameters, restoring factory default parameters and importing/exporting configuration files. • Local Camera Management: The adding, deleting and editing of IP cameras.
User Manual of DS-7600NI Series NVR • Remote PTZ Control: Remotely controlling PTZ movement of the selected camera (s). • Local Video Export: Locally exporting recorded files of the selected camera (s). 7. Click the OK button to save the settings and exit interface. Note: Only the admin user account has the permission of restoring factory default parameters. 13.4.2 Deleting a User Steps: 1. Enter the User Management interface. Menu >Configuration>User 2.
User Manual of DS-7600NI Series NVR Figure 13. 9 Edit User Interface 4. Edit the user information, including user name, password, level and MAC address. Check the checkbox of Change Password if you want to change the password of the current user. 5. Click the OK button to save the settings and exit the menu.
User Manual of DS-7600NI Series NVR Appendix 178
User Manual of DS-7600NI Series NVR Glossary • Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF. • HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters with magnetic surfaces.
User Manual of DS-7600NI Series NVR Troubleshooting No image displayed on the monitor after starting up normally. Possible Reasons a) No VGA or HDMI connections. b) Connection cable is damaged. c) Input mode of the monitor is incorrect. Steps 1. Verify the device is connected with the monitor via HDMI or VGA cable. If not, please connect the device with the monitor and reboot. 2. Verify the connection cable is good.
User Manual of DS-7600NI Series NVR Possible Reasons a) Network failure, and the NVR and IPC lost connections. b) The configured parameters are incorrect when adding the IPC. c) Insufficient bandwidth. Steps 1. Verify the network is connected. 1) Connect the NVR and PC with the RS-232 cable. 2) Open the Super Terminal software, and execute the ping command. Input “ping IP” (e.g. ping 172.6.22.131). Note: Simultaneously press Ctrl and C to exit the ping command.
User Manual of DS-7600NI Series NVR No monitor connected with the NVR locally and when you manage the IPC to connect with the device by web browser remotely, of which the status displays as Connected. And then you connect the device with the monitor via VGA or HDMI interface and reboot the device, there is black screen with the mouse cursor.
User Manual of DS-7600NI Series NVR b)Poor network between NVR and PC, and there exists packet loss during the transmission. c) The performances of hardware are not good enough, including CPU, memory, etc.. Steps: 1. Verify the network between NVR and IPC is connected. 1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable. 2) Open the Super Terminal, and execute the command of “ping 192.168.0.
User Manual of DS-7600NI Series NVR Log in the IPC directly, and turn the audio on, check if the sound is normal. If not, please contact the manufacturer of the IPC. 2. Verify the setting parameters are correct. Select “Menu > Record > Parameters > Record”, and set the Stream Type as “Audio & Video”. 3. Verify the audio encoding standard of the IPC is supported by the NVR. NVR supports G722.
User Manual of DS-7600NI Series NVR Select “Menu > Configuration > General > General”, and verify the “Device Time” is correct. 2. Verify the search condition is correct. Select “Playback”, and verify the channel and time are correct. 3. Verify the HDD status is normal. Select “Menu > HDD > General” to view the HDD status, and verify the HDD is detected and can be read and written normally. 4. Check if the fault is solved by the above steps. If it is solved, finish the process.
User Manual of DS-7600NI Series NVR Summary of Changes Version 2.3.4 Added 1. Support adding IP cameras by the right-click menu. (Chapter 2.3.1) 2. Support smart search function. (Chapter 6.2.2) 3. Support connecting the third-party network cameras from Brickcom and Bosch. (Appendix-List of IP Cameras Compatible) Updated 1. Optimize the method for adding encoder. (Chapter 2.3.1) 2. Optimize the playback interface.
User Manual of DS-7600NI Series NVR List of Compatible IP Cameras List of Hikvision IP Cameras Note: For the list, our company holds right to interpret. Max. Type Model Version Sub-stream Audio Resolution DS-2CD883F-E V4.1.0 build 130111 2560×1920 √ √ DS-2CD783F-E(I) V4.1.0 build 130111 2560×1920 √ √ DS-2CD8283F-E(I) V4.1.0 build 130111 2560×1920 √ √ DS-2CD886BF-E V4.0.3 build 120913 2560×1920 √ √ DS-2CD886MF-E V4.0.3 build 120913 2560×1920 √ √ DS-2CD854F-E V4.1.
User Manual of DS-7600NI Series NVR Max. Type Model Version Sub-stream Audio Resolution SD Network Camera DS-2CD7164-E V4.1.0 build 130111 1280×720 √ × DS-2CD764FWD-E(I) V4.1.0 build 130111 1280×720 √ √ DS-2CD8264FWD-E(I) V4.1.0 build 130111 1280×720 √ √ DS-2CD2012-I V4.0.9 build 130106 1280×960 √ × DS-2CD2112-I V4.0.9 build 130106 1280×960 √ × DS-2CD2212-I V4.0.9 build 130106 1280×960 √ × DS-2CD2312-I V4.0.9 build 130106 1280×960 √ × DS-2CD2032-I V4.0.
User Manual of DS-7600NI Series NVR Max. Type Model Version Sub-stream Audio Resolution DS-2CD976-V(B) DS-2CD976(C) V3.1.0 build120423 1600×1200 × × DS-2CD976-V(C) V3.1.0 build120423 1600×1200 × × V3.1 build 120423 1920×1080 × × DS-2CD986A(B) V3.1.0 build120423 2448×2048 × × DS-2CD986A(C) V3.1.0 build120423 2448×2048 × × DS-2CD986C(B) V2.3.6 build 120401 2560×1920 × × DS-2DF1-572 V4.0.2 build 120813 1280×720 √ √ DS-2DF1-57A V4.0.2 build 120813 1280×720 √ √ V4.1.
User Manual of DS-7600NI Series NVR Max. Type Model Version Sub-stream Audio × √ Resolution DS-6604HCI DS-6601HFI DS-6602HFI V1.2.
User Manual of DS-7600NI Series NVR List of Third-party IP Cameras Note: ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its private protocols. Only ONVIF is supported refers to the camera can only be supported when it uses the ONVIF protocol. Only AXIS is supported refers to the function can only be supported when it uses the AXIS protocol. IPC Manufacturer or Max.
User Manual of DS-7600NI Series NVR IPC Manufacturer or Max. Model Version Protocol Panasonic Sub-stream Audio 1280×960 × √ 800×600 √ × 1280×960 √ √ 1280×960 √ × 1280×960 √ √ 1280×960 √ × 640×360 √ × 640×480 √ × 1280×960 √ √ 1920×1080 √ √ 1920×1080 √ × 1280×960 √ √ 800×600 √ √ 800×600 √ √ 800×600 √ √ 1280×960 √ √ 1280×960 √ √ 1280×960 √ √ 1280×960 √ × 1920×1080 √ × 2048×1536 √ × Resolution VB-M7000F Ver.+1.0.
User Manual of DS-7600NI Series NVR IPC Manufacturer or Max. Model Version Protocol Sub-stream Audio Resolution VCC-HD4600P 2.03-02(110315-00) 1920×1080 × √ SNC-CH220 1.50.00 1920×1080 × × 1.73.00 1280×720 √ √ 1.53.00 1920×1080 √ √ 1.50.00 2048×1536 × × 0203a 640×480 × × 0107a 1280×800 × × 0104a 1600×1200 × √ 0102a 640×480 × × 0105b 1280×800 × × D5110 MG.1.6.03P8 1280×1024 √ × F3106 M2.1.6.03P8 1280×1024 √ √ F3110 M2.1.6.
User Manual of DS-7600NI Series NVR 194
