Installation Instruction
D Installaon instrucon
Dashcam
·
G2
User Manul
Scan and download the APP
51 2 3 4 6
1. TF Slot
Insert the TF slot and
start the video.
2. RESET
Reset the device
3. Stop monitoring indicator light
Device in stop monitoring mode
4. Cam lens
7. TVI Camera Connector
8. MIC
6. Micro USB Connector
Power connector
5. MINI USB Connector
Connect 4G module
10. Audio output
9. Power/Status indicator light
7
1
1
2
3
4
5
6
7
8
10
9
2
4
6
3
5
3
2
Disater box
for device
Micro USB
Clean the windscreen and
sck the stac film on the
windscreen,make sure no
bubble.
Adjust the angle of the
lens for your view.
Sck the device on the
stac film and get power
from the disater box.
Connect the katallobar as
aboved label.
C
Part SpecificaonB
Packing List
7
4
1
ACC
VCC
GND
1. Dashcam x 1
4. TVI Cam(oponal) x 1
5. Stac film x 2
3. BT remote control x 1
2. Katallobar x 1
6. User manul x 1
7. 3M glue x 2
A Regulatory Informaon A Regulatory Informaon A Regulatory Informaon A Regulatory Informaon
FCC Informaon
Please take aenon that changes or modificaon not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device , pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference
will not occur in a parcular installaon. If this equipment does
cause harmful interference to radio or television recepon, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.
FCC Condions
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operaon.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and
comply therefore with the applicable harmonized
European standards listed under the RE Direcve
2014/53/EU, the EMC Direcve 2014/30/EU, the
LVD Direcve 2014/35/EU, the RoHS Direcve
2011/65/EU
2012/19/EU (WEEE direcve): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collecon points. For more informaon see: www.
recyclethis.info
The power supply must conform to LPS. The
recommended adaptor model is C10, whose
manufacturer is Dongguan NB Power Electronic
Limited. Use this kind of adaptor, and do not
change the adaptor randomly.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards
requirements.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operaon is subject to the following two condions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radioexempts de licence. L'exploitaon
est autorisée aux deux condions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'ulisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est suscepble d'en
compromere le fonconnement.
Under Industry Canada regulaons, this radio transmier may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmier by Industry Canada. To reduce
potenal radio
interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for
successful communicaon.
Conformément à la réglementaon d'Industrie Canada, le présent
émeeur radio peut
fonconner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émeeur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l'intenon
des autres ulisateurs, il faut choisir le type d'antenne et son gain
de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l'intensité nécessaire à l'établissement d'une
communicaon sasfaisante.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.
Cet équipement doit être installé et ulisé à une distance
minimale de 20 cm entre le radiateur et votre corps.
Operation distance statement for Camera