User's Manual

D Parts Introduction E Installation F Mobile Phone Connection G Basic Description
7
8
H Troublshooting
9
H Troubleshooting
10
11
12
Model
Aperture
Pixel
Max. Resolution
Angle
Screen
Storage
G-Sensor
Wi-Fi
Sound Recording
Power Supply
Power Consumption
Operating Temperature and Humidity
Installation Type
Dimensions (L × W × H)
Weight
AE-DC8222-C8PRO
F1.75
800 W
4K @ 30fps
Horizontal: 118°, Diagonal: 143°
2.4”
TF Card, 32 GB to 128 GB
Built-in, collision triggered recording and recording lock
Yes
Yes
5 VDC, 2 A
Approx. 5 W
-20 °C to 70 °C (-4 F to 158 F). Humidity 95% or less.
General
105 × 49 × 39mm (4.1ʺ × 1.9ʺ × 1.5ʺ)
Approx. 125 g (0.28 lb.)
Scan QR Code
<
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Specications
1
Clean the windshield and
paste the electrostatic lm
onto it.
Avoid introducing air bubble.
DO NOT paste the lm
repeatedly.
Paste the device onto the
electrostatic lm and route
cable to the disater box for
power supply.
Connect the power cord as
the gure above.
Adjust the angle to the
target direction.
Scan the QR code to download and
install HikDashcam app.
Add the dashcam to the app.
a. Run the HikDashcam app.
b. Tap Wi-Fi Connection.
c. In Wi-Fi list, select the Wi-Fi SSID
of the target dashcam and enter
Wi-Fi password to build
connection.
• You can set the parameters of the
dashcam.
• For iOS, you need to go to Wi-Fi
settings of your phone to connect
to the Wi-Fi of dashcam.
Edit the dashcam password to
activate it to avoid abnormal
recording after connecting to Wi-Fi.
1
Dashcam Wi-Fi default parameters:
• Wi-Fi SSID: HIKVISION-XXXX
(XXXX refers to the last four
characters of verication code.)
• Wi-Fi password: 1234567890
(please edit password after logging in
for the rst time.)
Start Up
Connect the power cord to the car battery.
Device starts recording automatically once the car started.
Trouble Solution SolutionTrouble
The dashcam drops
easily.
Starting the dashcam
failed.
The dashcam powers
o easily.
Recording is
abnormal and
indicator is unlit.
Recording is blurred.
Recording is mute.
Dashcam reboots
itself.
Clean the windshield before installation.
Check whether the vehicle is started and power
supply is normal.
Check whether the car charger is tightly connected.
Restore to defaults: hold the RESET button until the
startup music is heard.
Make sure the power cord is in good condition.
Make sure the power cord is tightly connected to the
according interfaces.
Make sure that the dashcam started up successfully.
Check whether the TF card is inserted.
Check the status of TF card, e.g. its format, its lifespan.
Change TF card if it is not well.
Make sure the protective lm is peeled o.
Check whether the windshield or the lens of dashcam
is blurred.
Set audio settings on the device or turn on sound
recording in HikDashcam app.
Check whether the car charger is equipped with power
supply interface of 5 VDC, ≥ 2 A.
The mobile phone
cannot display
recordings.
It may be relevant with the player or system of the
phone. Please connect TF card to your computer and
display the recordings.
TF card is not
detected when you
connect dashcam to
computer with the
supplied power cord.
Dashcam does not support data transmission and the
supplied power cord is only for charging.
If you need to transfer data, please connect TF card
to your computer.
Wi-Fi connection
takes a long time.
It may be caused by the interferrence of the
surrounding Wi-Fi signals. Please use the dashcam in
an environment of less interferrence.
Shut down unnecessary programs in your phone to
release some resources for HikDashcam app and
reconnect Wi-Fi.
Dashcam Wi-Fi
password is forgotten.
The default password is 1234567890. If you have
revisied the password, regain the password by the
following steps.
1. Hold the RESET button on dashcam until the startup
music is heard and the dashcam is restored to
defaults.
2. Go to Wi-Fi Connection interface in HikDashcam
app.
3. Select Wi-Fi SSID and log in with default password
1234567890.
1
2
3
·
Check whether the car charger is tightly connected.
·
Check whether the 3M tape is tightly sticked to the
electrostatic lm before the installation.
·
Turn on sound through the the audio control function
of the dashcam.
·
·
Mobile phone cannot
connect to dashcam.
Make sure HikDashcam app is installed.
Please restart the dashcam to the app.
No GPS signal.
·
·
Check whether the GPS function is enabled.
Normally, the GPS function is enabled by default.
Make sure the device is not in the places of weak
signal or no signal, such as underground garage.
· Make sure there is no metal around the device
·
because metal will interfere with GPS signal.
Make sure the location where the device is installed is
not pastd with radiation protection lm. The lm will
interfere with GPS signal.
1. Camera
2. Holder
3. Loudspeaker
6. Mini USB Interface
Access to 4G module/
Data transmission
5. Camera Interface
7. Microphone
8. TF Card Slot
9. RESET Button
10. Screen
4. Power Supply Interface
When the car is off, device turns into parked monitoring mode and start to record
once the current scene changed or collision happened.
2
43
Recording
Recordings are divided to ordinary video and emergency video.
You can set the video voice on/off via System Settings or
Hikdashcam APP.
C Packing List
6
1
2
3
5
4
1.
Dashcam × 1
2 .
Power Cord × 1
3. Power Cable × 1
4 .
Electrostatic Film × 1
5 .
User Manual × 1