User Guide
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
1
2
3
AX PRO M2
Quick Start Guide
UD25793B-B
Please pull the antenna cable
carefully to prevent damage.
1
1
2
3 4
6 75
2
1
6
7
3
2
4
5
power
xxxx
OR
POWER ON
TRIGGER
Add Device
Sites:xxx
My Device
OR
Hik-Connect
Hik-ProConnect
4 User Manual
E N G L I S H
Specication
Appearance
Note: Power down the control panel before installation.
1. Loosen the screws and open the case.
2. Take out the main board.
3. Fix the rear case on the wall.
4. Install the main board.
5. Install the loudspeaker.
6. Connect the power supply and turn on the switch.
7. Close the case and tighten the screws.
1
Set Up
User Manual
Installation
2
3
4
1. Main Board
5. Battery
6. Antenna Position
2. 4G Module
7. Loudspeaker
3. Power Switch 4. Tamper Switch
1.Add the AX PRO to Hik-ProConnect or Hik-Connect APP.
2.Enroll the peripheral to the AX PRO.
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation
RF frequency 433 Mhz
Keyfob 48
Wireless sounder 6
Keypad 8 (Including tag reader)
Wireless repeater 4
Tag 48
Zone 96 (up to 48 PIRCAMs)
Transmitter Up to 96 (Single), up to 6 (Multi)
Onboard video clip 4
User
Admin, installer, user 1, 120, 46
Area 32
LEDs indication Arm/Disarm, Alarm, Alert, Cloud, Power
Memory Log stored
Alarm&abnormal (3000), user operation
(1500), user management (200)
Programming tool
Hik-Connect/Hik-ProConnect/Web Portal/
IVMS4200/ Convergence Cloud
Network Wired network, Wi-Fi, 3/4G on board
SIA DC09 (SIA level 2, Contact ID), ISUP, ISAPI
(SDK), CSV-IP, FSK Module
Hik-IP Receiver & Hik-IP Receiver Pro (Sur-
Gard & Ademco 685)
Supports video verification and remote
control
SIM slot Dual
Power supply
100 to 240V~, 50/60 Hz, 0.2A to 0.1A
Battery type
12v 7Ah storage battery (sold separately),
up to 36 hours
Operation
temperature
-10 °C to 40 °C
Dimension (W×H×D) 261 mm × 199 mm × 86.4 mm
Weight 975g (No battery)
Others
Basic
Software
ARC protocol
Communication
Hardware