Quick Start Guide

1
2
Operation via
Client Software
Testing
Powering On
Wiring
Network
Security Control Panel
Quick Start Guide
Connect the keypad, alarm output, trigger, and power cables,with following the figure below. Power down the control panel
before connecting and disconnecting accessories and peripherals.
Step 1 Wiring
The keypad registraon will be completed in 1 minute aer the control panel
being power on. The system then will complete the start-up and enter the
properly status of working in 20 seconds.
While the registraon is succeeded, the working status indicator of LED keypad will
turn green.
The display demonstraon of LCD keypad aer powering on is shown below.
HIKVISION
20XX.XX.XX XX:XX:XX
VX.X.X build XXXXXX
Step2 Powering On
Dry Contact Dry Contact Dry Contact Dry Contact
2.2KΩ
NC
C
Z
G
Peripheral Security Detector
NC Detector
2.2KΩ
NO
C
Z
G
Security Control PanelSecurity Control Panel Security Control Panel
NO Detector
Peripheral Security Detector
Zone
Zone
Alarm Output
KeypadPower Supply
G Z4 G Z6Z5 G Z8Z7GZ1 Z2 Z3
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
NO/NC1
COM1 COM2 COM3 COM
NO/NC2
NO/NC3 NO/NC4
G Z4 G Z6Z5 G Z8Z7GZ1 Z2 Z3
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
TX
RX
G
Printer
Dry Contact Dry Contact
Dry Contact Dry Contact
D
+ +
D G12V
-
Keypad
DC_IN
+
G
BAT
_
+12V G
+12V
G
14.3V DC
Power
12VDC 7AH
Lead-acid
Alarm
Bell
Auxiliary
Power
Interface
BELL
AUX
Network Data Indicator
14.3 Power Indicator
Reset
TAMPER1
BELL
AUX
FUSE
KEYPAD
Network Status Indicator
Working Indicator
3.3V Power Indicator
G Z10Z9
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
G Z12Z11
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
G Z14Z13
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
G Z16Z15
N.O N.O
2.2K
EOL
2.2K
EOL
N.C N.C
Z9 to Z16 are only supported by the network security control panel with 16 zones.
Power Indicator
Telephone Module
Handset
Incoming
Phone Line
GPRS Module
DC
Network Extension Module
Network Data Indicator
Network Status Indicator
Unoccupied Zone
NO/NC1
COM1 COM2 COM3 COM
NO/NC2
NO/NC3 NO/NC4
The resistance of 2.2KΩsupports
tamper-proof and non-tamper-proof
wiring.
The resistance of3.3KΩ, 5.6KΩor
8.2KΩ only supports non-tamper-proof
wiring.
UD07393B