Network Security Control Panel User Manual Network Security Control Panel User Manual UD07466B i
Network Security Control Panel User Manual User Manual COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Security Control Panel User Manual IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. 0201001061111 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Security Control Panel User Manual This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the R&TTE Directive 1999/5/EC, the EMC Directive 2004/108/EC, the LVD Directive 2006/95/EC, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Network Security Control Panel User Manual Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Network Security Control Panel User Manual heating and can be a fire hazard. When the product is installed on a wall or ceiling, the device should be firmly fixed. To reduce the risk of fire or electrical shock, do not expose the indoor used product to rain or moisture. This installation should be made by a qualified service person and should conform to all the local codes. Please install blackouts equipment into the power supply circuit for convenient supply interruption.
Network Security Control Panel User Manual Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type.
Content Chapter 1 System Introduction __________________________________ 3 1.1 Overview ____________________________________________________ 3 1.2 System Definition _____________________________________________ 3 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 Chapter 2 2.
Network Security Control Panel User Manual Chapter 3 Trouble Shooting ___________________________________ 45 2
Network Security Control Panel User Manual Chapter 1 System Introduction 1.1 Overview Network security control panel uses embedded microcontroller technology for zone monitoring and system status detection. The alarm or status reports can be transmitted to the central alarm monitoring station through programming. Multiple alarm types and report transmission methods (telephone network, the Ethernet network, and the GPRS wireless network) are supported.
Network Security Control Panel User Manual public partition are in the arming status. The public partition is disarmed automatically when any of partitions linked with the public partition is in the disarming status. The user also can arm or disarm the public partition independently. Limit For the public partition of multiple security control panels, up to 2 other partitions can be linked to it. 1.2.3 Zone Definition Zone is a basic concept in the security control panel system.
Network Security Control Panel User Manual the zone detects alarm events, the sound and light alarming prompt will be triggered on the keyboard. The siren output will be triggered when the siren is linked, meanwhile the generated event report will be uploaded to the center receiver (the uploaded report is different with the report of 24-Hr Audible Alarm Zone), and the zone alarm status can be checked on the client.
Network Security Control Panel User Manual After arming the system, if the delayed Zone is first triggered, the system will provide an entry delay when the interior follower zone is triggered. If not, the interior follower zone will trigger alarm instantly. The delay parameters of interior follower zone are the same with the e delayed zone. It is mostly set in the rest room or hall (e.g. motion detector), which is a key place to operate keyboard for users.
Network Security Control Panel User Manual the area and not trigger alarm. Disarming If you want to turn off the arming of the detectors, you should disarm the system. Then the zones that disarmed are not protected, even an event occurs and triggers the detectors, and no alarm will be trigger by controller. Bypass You can bypass any zone to turn off the protection of it when some exception occurs while other zones can work normally.
Network Security Control Panel User Manual Chapter 2 System Controlling 2.1 Keypad Operation Code Single Partition Mode Default Status: the control is in the single partition mode, that is, only partition 1 is enabled. Multi-Partitions Mode 1) In the multi-partitions mode (equal to or more than 2 partitions), there are 2 modes for keypad operations: global keypad mode, and partition keypad mode. Global Keypad Mode: In this mode, the user does not enter the partition.
Network Security Control Panel User Manual Demonstration: LCD Display E.g., the installer password is 012345. Press the installer password: [0] [1] [2] [3] [4] [5]. Press [*] to enter the working mode. xxxxxx*89 Press the device initialization command: [8] and [9]. Press [#] to confirm If the operation is successful, the operation. Operation Succeeded If the operation is failed, Operation Failed 2.1.
Network Security Control Panel User Manual Demonstration: LCD Display E.g., the user password is 1234. Arming: The current status is status of disarming. Press the user password: [1] [2] [3] [4]. xxxx Press [#], and the If the operation is successful, status of disarming Operation Succeeded will be changed into arming. If the operation is failed, Operation Failed Disarming: The current status is status of arming. Press the user password: [1] [2] [3] [4].
Network Security Control Panel User Manual Demonstration: E.g., the user password is LCD Display 1234, and the zone No. Is 3. Press the user password: [1] [2] [3] [4]. Press the bypass key: . xxxx Bypass 03 Press the zone No.: [0] [3]. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: E.g., the user password is 1234, and the zone is LCD Display No. 03, No. 04, and No. 05. Press the user password: [1] [2] [3] [4]. Note: For the continuous bypass operation, the user password is required to be entered once only. Press the bypass key to bypass zone No. 3. xxxx Bypass 03 Press the zone No.: [0] [3]. Press [#] to confirm the operation. Press the bypass key to bypass zone No. 4. Press the zone No.: [0] [4].
Network Security Control Panel User Manual Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed Multi-zones bypass/bypass recovery should be conducted in 15 seconds. For example, bypass operations of the zone No. 04 and zone No. 05 should be completed in 15 seconds in the above demonstration. 2.1.4 Instant Arming Function: The control panel can be set into the instant arming status via the keypad.
Network Security Control Panel User Manual 2.1.5 Stay Arming Function: After the operation is completed, the partition will change the status of disarming (current status) into arming immediately. The bypass supported zone of the partition will do auto-bypass simultaneously. Command: [User Password］+［*］+［4］+［#］ Demonstration: E.g., the user password is LCD Display 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode.
Network Security Control Panel User Manual Demonstration: LCD Display E.g., the user password is 1234, and the zone number is 03. Press the user password: [1] [2] [3] [4]. Press the bypass key: . xxxx Bypass Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed Force Instant Arming Function: After the operation is completed, all the zones in fault status except the 24-hour arming zones will be bypassed.
Network Security Control Panel User Manual Demonstration: LCD Display E.g.,the user password is 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*7Bypass Press[7], and the control panel enters the force instant arming status. Press the bypass key: . Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: LCD Display E.g.,the user password is 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*4 Press [4], and the control panel enters the force stay arming status. Press the bypass key: . Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed 2.1.
Network Security Control Panel User Manual Demonstration: E.g., the user password is LCD Display 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*1 Press [1] to cancel the alarm under the arming status. Press [#] to confirm the If the operation operation.
Network Security Control Panel User Manual Demonstration: LCD Display E.g., the user password is 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*1 Press [1] to cancel the alarm under the disarming status. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: LCD Display Press [*] to enter the working mode. Press [1] to cancel the alarm under the disarming status. *1 Press [#] to confirm the operation. If the operation is successful, Operation Succeeded If the operation is failed, Operation Failed 2.1.8 Single-Zone Operation Single-Zone Arming and Disarming Function: The operation of control panel arming and disarming is the same.
Network Security Control Panel User Manual (［n］+［n］+［n］ refer to the 3-digit alarm output channel No..) Demonstration: E.g., the user password is LCD Display 1234, and the alarm output channel No. is 001. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. Enable the alarm output by pressing [8] [5]. xxxx*85001 Press the alarm output channel No.: [0] [0] [1]. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: E.g., the user password is 1234, and the alarm output channel No. is 001. LCD Display The alarm output function of the alarm output channel No. 001 has been enabled. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. Disable the alarm output by pressing [8] [6]. xxxx*86001 Press the alarm output channel No.: [0] [0] [1]. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual 2.1.11 Group Bypass Group Bypass Function: After a partition is conducted with group bypass, all the alarm devices in groupbypass supported zone of the partition will be blocked. Command:［User Password］ + ［*］ + ［4］ + ［1］ + ［#］ Demonstration: E.g., the user password is LCD Display 1234. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*41 Enable group bypass by pressing [4] [1].
Network Security Control Panel User Manual Demonstration: E.g., the user password is LCD Display 1234. Press the user password: [1] [2] [3] [4]. Press [*] to working mode. enter the xxxx*42 Disable group bypass by pressing [4] [2]. Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed Group bypass operation and group bypass recovery operation are available to all group bypass supported zones in the partition. 2.1.
Network Security Control Panel User Manual Demonstration: E.g., the master code is 1111, the user LCD Display No. Is 001, and the new user password is 5678. Enter Password Changing Progress: ［Master Code］ + ［*］ + ［0］ + ［#］ Press the master code: [1] [1] [1] [1]. Press [*] to enter the working mode. Press [0] to enter the password changing progress. xxxx*0 Please Enter the User No. Press [#] to confirm the operation. Appoint the User:［User No.］ + ［#］ Press the user No.
Network Security Control Panel User Manual Press the new password of the appointed user again: [5] [6] [7] [8]. Press [#] to confirm the new password. xxxx 2.1.13 Changing User Password via Master Code Function: You can change the user password of the keypad via the master code. Command: ［Master Code］ + ［*］ + ［0］ + ［#］ ［User No.］ + ［#］ ［New Password］ + ［#］ ［New Password］ + ［#］ The user password will be changed by the above four steps. 2.1.
Network Security Control Panel User Manual Demonstration: E.g., the user password is LCD Display 1234, the keyfob No. is 01, and the partition No. is 08. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*9101 Press [9] [1] to enter the code matching mode. Enter the keyfob No.: [0] [1]. Enter the partition.: [0] [8] xxxx*910108 Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed 2.
Network Security Control Panel User Manual Demonstration: E.g., the user password is LCD Display 1234, and the keyfob No. is 001. Press the user password: [1] [2] [3] [4]. Press [*] to enter the working mode. xxxx*9101 Enter the mode for deleting code matched keyfob by pressing [9] [0]. Press the keyfob No.: [0] [0] [1]. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Press any key of the keyfob to delete the keyfob from the control panel. If the operation is successful, Operation Succeeded If the operation is failed, Operation Failed Press[*]+[#]to exit the registration mode. Deleting All Code-Matched keyfob Function: You can delete all keyfobs which have matched code with the control panel. Command: [User Password] + [ * ] + [ 9 ] + [ 2 ] + [ # ] Demonstration: E.g., the user password is LCD Display 1234.
Network Security Control Panel User Manual Matching the Card No. with the Control Panel 1. Enter the matching mode Command: [Master Code] + [Project] + [10] + [User No.] + [#] Demonstration: E.g., the master code is LCD Display 1234, and the user No. is 003. Press the master code: [1] [2] [3] [4]. Press [Project] to enter the project mode. Press [1] [0] to the mode for entering the user’s card No.. xxxxProject003 Press the user No.: [0] [0] [3].
Network Security Control Panel User Manual Demonstration: E.g., the master code is LCD Display 1234. Press the master code: [1] [2] [3] [4]. Press [Project] to enter the project mode. xxxxProject003 Press [1] [2] to enter the deleting card mode. Press [#] to confirm the If the operation is successful, operation. Deleting Card... If the operation is successful, Swipe the card.
Network Security Control Panel User Manual Demonstration: E.g., the master code LCD Display is 1234, and the user No. is 001. Press the master code: [1] [2] [3] [4]. Press [Project] to enter the project mode. xxxxProject111234567890 Enter the mode for deleting appointed matched card by pressing [1] [2] [3] [4] [5] [6] [7] [8] [9] [0].. Press [#] to confirm If the operation is successful, the operation.
Network Security Control Panel User Manual Demonstration: E.g., the master code is LCD Display 1234, and the user No. is 001. Press the master code: [1] [2] [3] [4]. Press [Project] to enter the project mode. xxxxProject15001 Enter the mode for deleting all matched cards by pressing [1] [5]. Press the user No.: [0] [0] [1]. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: E.g., the installer password is 012345, and the zone No. is 005 LCD Display Enter the installer password:[0][1][2][3][4][5] Press［*］[95][005][#] to enter the adding mode xxxxxx*95005 Trigger the wireless detector to add the detector to the control panel. If the operation is successful, Operation Succeeded If the operation is failed, Operation Failed Press[*]+[#]to exit registration mode.
Network Security Control Panel User Manual the control panel. Operation Succeeded If the operation is failed, Operation Failed Press[*]+[#]to exit the registration mode. 2.1.17 Deleting RS-485 Expander/Receiver from Control Panel Function: The control panel will unregister the RS-485 expander. However, if the expander is still connected with the control panel, it will be re-registered after control panel rebooting.
Network Security Control Panel User Manual Demonstration: E.g., the installer password LCD Display is 012345，RS-485 address is 09. Enter the installer password: [0] [1] [2] [3] [4] [5]. Press [*] to enter the working mode. xxxxxx*Project09 Press[Project]. Enter[0] [9] as the address of the RS-485 expander Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed 2.1.
Network Security Control Panel User Manual Demonstration: E.g., the installer password LCD Display is 012345. Enter the installer password: [0] [1] [2] [3] [4] [5]. Press [*] to enter the working mode. xxxxxx*0 Press [0] to enter the programming mode of control panel. Press [#] to confirm the If the operation is successful, operation. Operation Succeeded Programming... If the operation is failed, Operation Failed Exiting Programming Mode Command:［*］ +［#］ 2.1.
Network Security Control Panel User Manual 2.1.20 LCD Backlight Control LCD Backlight Time Control Function: The duration of enabling LCD backlight can be configured via the keypad. Command:［*］+［5］+［2］+［n］+［n］+［n］+［#］ Demonstration: E.g., the duration of LCD Display enabling LCD backlight is 15 seconds. Press [*] to enter the working mode. Enter the LCD backlight configuration mode by pressing [5] [2]. *52015 Pressing the backlight-on duration: [0] [1] [5]. Note: [0] [1] [5] means 15 seconds.
Network Security Control Panel User Manual Display English Command: [ * ] + [ 9 ] + [ 1 ] + [ 1 ] + [ # ] Display Chinese Command: [ * ] + [ 9 ] + [ 1 ] + [ 0 ] + [ # ] 2.1.22 Zone Testing Enter the Testing Mode Function: The zone testing function is used for keypad debugging. Command:［Installer Password］ + ［*］ + ［6］ + ［0］ + ［#］ Demonstration: E.g., the user LCD Display password is 1234. Press the user password: [1] [2] [3] [4]. xxxx*60 Press [*] to enter the working mode.
Network Security Control Panel User Manual the alarm is dismissed. If the zone is disarmed, it will exit the zone testing mode automatically. The function of exiting the testing mode is only available for security control panel in the version of 2.3 and above. 2.1.23 Test Report Manually Relaying Function: You can relay test report manually. One operation generates one test report.
Network Security Control Panel User Manual 2.1.24 Project Mode Function: You can enter the project mode, and configure the control panel via the keypad. Entering Project Mode Command:［User Password］ + ［Project］ + ［9］+ ［0］+ ［n］ + ［#］ Demonstration: E.g., the user password is 1234, and you want LCD Display to configure the telephone uploading mode. Press the user password: [1] [2] [3] [4]. Press the project key Project. Press the control panel debugging command: [9] [0].
Network Security Control Panel User Manual Press [*] [#]. When the value of n is 1 or 2, it means telephone 1 or 2. When the value of n is 3 or 4, it means network 1 or 2. When the value of n is 5 or 6, it means GPRS center 1 or 2. 2.1.25 Control Panel Soft Recovery Function: You can do the control panel soft recovery operation via the keypad. There is a default value of the master code, which can control all partitions and be modified.
Network Security Control Panel User Manual This function is only valid for bus security control panel. Command:［Installer Password］ + ［*］ + ［8］ + ［2］ + ［#］ Demonstration: E.g., the installer LCD Display password is 012345. Press the installer password: [0] [1] [2] [3] [4] [5]. Press [*] to enter the working mode. xxxxx*82 Press [8] [2] to enter the auto-searching mode of the global keypad. Press [#] to confirm the If the operation is successful, operation.
Network Security Control Panel User Manual Demonstration: E.g., the installer password LCD Display is 012345. Press the installer password: [0] [1] [2] [3] [4] [5]. Press [*] to enter the working mode. xxxxx*83 Press [8] [3] to enter the auto-registration mode of the global keypad. Press [#] to confirm the If the operation is successful, operation. Operation Succeeded If the operation is failed, Operation Failed 2.1.
Network Security Control Panel User Manual Chapter 3 Trouble Shooting Q: What is the function of Project button of LCD keypad? A: Project button has button switch function besides normal instruction button, such as: When sensor or module is abnormal, press and hold the Project button to switch to other interfaces manually.
Network Security Control Panel User Manual Enter programming Green, Blink Parameters Initialization Green, Blink System Abnormal Green, Blink System Normal Green, Normally On Q: What are the steps of LED keypad to program the control panel？ A： 1. In overall keypad programming mode, the program command is: {installer password} + {*} + {0} + {#}; 2.
Network Security Control Panel User Manual Sensor Normal Off Sensor Error Red, Normally On Sensor Alarm Red, Blink Sensor Bypass Green, Normally On LED keypad Camera indicator under Project Mode: No. Description No. Description 1 Off-hook 5 Send CID Report 2 Dial 6 Receive Alert Sound 3 Alarm Connecter Disconnection 7 Control Panel Off-hook 4 Receive the Hand-shack Sound 8 Alarm Connector On-hook LED keypad Camera indicator under Status Mode: No. Description No.
Network Security Control Panel User Manual A: There are two situations of removing alarm memory as shown below: 1) Under disarming mode: Press {*} + {1} + {#} or {Password} + {*} + {1} + {#}. 2) Under arming mode: Press {Password} + {*} + {1} + {#}. Q: How to input hexadecimal number? A: Input hexadecimal number with {*} button and number button {0} ~ {5}.
Network Security Control Panel User Manual DIP Ad d.
Network Security Control Panel User Manual A: The password for each operator should be different; otherwise the setting will be failed. For example, if the password of operator 1 is set to be 1234 hen password of operator 2 is also 1234, it will prompt to be error. In addition, the password of each operator should be different from the control panel duress code of other operators; otherwise the setting will be failed. For example if the password of operator No.3 is 3456 and the password of operator No.
Network Security Control Panel User Manual to disarm; 1) Initialize the hardware, restore the password of operator, main operator password and permission, and then disarm with main operator. The initialization password of operator is: 012345, the initialization password of main operator is: 1234, the permission is: arm/disarm. There is arm/disarm report and bypass is permitted. Please refer to FAQ of hardware initialization for more information about hardware initialization.
Network Security Control Panel User Manual Q: What if the client cannot log in the device? A: Troubleshoot according to the prompt. Please check if the device IP Address and Port No. are correct. The device default IP Address is: 192.0.0.64, and the Port No. is: 8000. Please check if the user name and password to log in the control panel are correct. The default user name is: admin, the word is: 12345.
Network Security Control Panel User Manual 3) WIFI parameter setting is incorrect; 4) SIM Card has no enough tariffs.
