Camera Network Mini Dome Camera Quick Start Guide UD04385B 0
Network Mini Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Mini Dome Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Mini Dome Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Mini Dome Camera·Quick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Network Mini Dome Camera·Quick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
Network Mini Dome Camera·Quick Start Guide ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Network Mini Dome Camera·Quick Start Guide ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.
Network Mini Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Overview of Type I Mini Dome Camera ......................... 10 1.2 Overview of Type II Mini Dome Camera ........................ 10 1.3 Overview of Type III Mini Dome Camera ....................... 13 2 Installation .................................................................................... 15 2.1 Type II Mini Dome Camera Installation ......
Network Mini Dome Camera·Quick Start Guide 5.4 Initializing the Memory Card .........................................
Network Mini Dome Camera·Quick Start Guide 1 Appearance Description 1.1 Overview of Type I Mini Dome Camera 4 5 2 3 7 8 6 Figure 1-1 Overview of Type I Mini Dome Camera 1.
Network Mini Dome Camera·Quick Start Guide Figure 1-3 Overview of Type II Mini Dome Camera (2) Table 1-1 Description of Type I/ II Mini Dome Camera No.
Network Mini Dome Camera·Quick Start Guide No. Description 9 Audio/Alarm Cables (Supported by Type II camera) 10 Wi-Fi Antenna 11 Hex Screw 12 MIC 13 RESET/WPS Button(Supported by Type II camera) Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. No.
Network Mini Dome Camera·Quick Start Guide 2. Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network. The WPS button works as a reset button only when you press it when the camera is powering on. Press the WPS button on the camera, and then press the WPS button on the router will establish a connection as well, and the expire time of WPS connection on the camera is 120s.
Network Mini Dome Camera·Quick Start Guide Table 1-3 Description of Type IIIMini Dome Camera No. Description 1 Cover 2 Lens 3 Power LED indicator, It turns solid red when power is connected. 4 Base Plate 5 Set Screw Hole 6 Set Screw of Lens 7 S & L: Network Status Indicator. When the network is connected, the “S” LED is solid yellow, while the “L” LED flashes orange.
Network Mini Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Mini Dome Camera·Quick Start Guide Type I camera shares the similar appearance with the type II camera, we will take type I camera as the example to explain the installation steps, please 2.1 Type II Mini Dome Camera Installation 2.1.1 Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Drill Template 1 1 1 1 Hole A:for cables routed through the ceiling Screw hole 1:for Mounting Base FRONT Figure 2-1 Drill Template 2.
Network Mini Dome Camera·Quick Start Guide Figure 2-2 Disassemble the Camera 3. Hammer the plugs of the expansion screws to the screw holes. 4. Align the adapter plate to the drill template, and fix the adapter plate.
Network Mini Dome Camera·Quick Start Guide 5. Connect the power cable, network cable, and the audio/alarm cables. 6. Fix the camera body to the ceiling with the supplied expansion screws. Figure 2-4 Fix the Camera Body 7. View the image via the web browser. 8. Slightly loosen the hex screw beside the WPS/RESET button to adjust the surveillance angle. 9. Use the supplied adjusting tool to adjust the pan [±30°], tilt [0~80°], and rotation direction [0~360°].
Network Mini Dome Camera·Quick Start Guide Pan Adjusting Tool Rotation Tilt Figure 2-5 3-Axis Adjustment 10. Tighten the hex screw to fix the well-adjusted surveillance angle. 11. Align the front cover to the dome drive and tighten the set screws on the front cover. Figure 2-6 Install the Front Cover 12. Tear off the protection film softly to complete the installation.
Network Mini Dome Camera·Quick Start Guide Do not tear off the protection film until the installation is completed. Do not touch the inside face of the bubble with your hands. 2.1.2 Ceiling Mounting with a Gang Box Steps: 1. Fix the adapter plate to the gang box with the supplied PM4X8 screws. Figure 2-7 Fix the Adapter Plate 2. Fix the dome drive to the adapter plate with the supplied PM4X8 screws.
Network Mini Dome Camera·Quick Start Guide Figure 2-8 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover. Figure 2-9 Install the Front Cover 5. Tear off the protection film softly to complete the installation.
Network Mini Dome Camera·Quick Start Guide Do not tear off the protection film until the installation is completed. Do not touch the inside face of the bubble with your hands. 2.1.3 Pendent Mounting Steps: 1. Install the bracket to the ceiling with the supplied screws in the bracket package. You need to purchases a pendant bracket separately if pendent mounting is adopted. 2. Fix the camera body to the pendent bracket with the supplied PM4X8 screws. Figure 2-10 Fix the Adapter Plate 3.
Network Mini Dome Camera·Quick Start Guide Figure 2-11 Fix the Dome Drive 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation. Figure 2-12 Install the Front Cover 5. Tear off the protection film softly to complete the installation.
Network Mini Dome Camera·Quick Start Guide Do not tear off the protection film until the installation is completed. Do not touch the inside face of the bubble with your hands. 2.1.4 Wall Mounting Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package. You need to purchases a wall bracket separately if wall mounting is adopted. Figure 2-13 Install Wall Bracket 2. Fix the adapter plate to the wall bracket.
Network Mini Dome Camera·Quick Start Guide Figure 2-14 Fix the Adapter Plate 3. Fix the dome drive to the wall bracket with the supplied screws. Figure 2-15 Install the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
Network Mini Dome Camera·Quick Start Guide Figure 2-16 Install the Front Cover 5. Tear off the protection film softly to complete the installation. Do not tear off the protection film until the installation is completed. Do not touch the inside face of the bubble with your hands. 2.1.5 Install the Micro SD Card This series of camera supports local storage, please refer to the following steps to install the micro SD card. Steps: 1. Remove the front cover by loosening the set screws on it.
Network Mini Dome Camera·Quick Start Guide Figure 2-17 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera.
Network Mini Dome Camera·Quick Start Guide 2.2 Type III Mini Dome Camera Installation Steps: 1. (Optional) Use a plier to remove the clip (marked in dotted line in Figure 2-19) on the side of the back box and then route the cables through the opening instead of the cable hole. Figure 2-19 Side Clip 2. Loosen the set screws with a hex key (supplied) to remove the cover.
Network Mini Dome Camera·Quick Start Guide 3. Install the micro SD card to the card slot. Figure 2-21 Install Micro SD Card 4. Fix the camera to the ceiling with the supplied screws. Figure 2-22 Fix the Camera 5. View the video image of the camera over the network.
Network Mini Dome Camera·Quick Start Guide 6. Loosen the lens set screws. Figure 2-23 Loosen the Lens Set Screws 7. Insert the hex key into the hole marked in the picture and rotate the hex key to adjust the panning position and tilting position until getting the desired surveillance angle. Tighten the set screws.
Network Mini Dome Camera·Quick Start Guide Figure 2-25 Adjust Tilting Position As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 8. Reinstall the cover before viewing the image so that you can get the same surveillance effect as the installation is done. 9. Install the cover, and tighten the set screws.
Network Mini Dome Camera·Quick Start Guide 2.3 Install the Water-proof Jacket It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor. Steps: 1. If the network cable has been settled down, cut off the plug of the network cable first. 2. Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body of the water-proof jacket, as shown in the figure. 3.
Network Mini Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Mini Dome Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Mini Dome Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Mini Dome Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Mini Dome Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Mini Dome Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Mini Dome Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Mini Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Mini Dome Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Mini Dome Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Mini Dome Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Mini Dome Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Mini Dome Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Mini Dome Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Mini Dome Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0
