Dome Network Camera Quick Start Guide
Quick Start Guide © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. Power Supply The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the LPS (Limited Power Source).
A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details. Cleaning Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. DO NOT use alkaline detergents. Using Environment When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.
Be sure that there is enough space to install the camera and accessories. Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that the wall is strong enough to withstand at least 4 times the weight of the camera and the mount. The standard power supply is 12 VDC or PoE, please make sure your power supply matches with your camera. Make sure that the power has been disconnected before you wire, install, or disassemble the device.
Incorrect Turn to page A and continue. i. Not necessarily included accessory. ii. Variable accessory amount. iii. Skip this step if not required.
Installation 1x 1x 1x 2x * 1x* 1x 1x 1x T20 T10 1x 1
Installation Interface Introduction Alarm Interface Audio Out Interface Audio In Interface Network Interface Power Interface Reset Button Memory Card Slot 2
Installation 1.
Installation 1.2 5.
Installation 2.1 A.1-A.3 B.1-B.
Installation A.1 A.2 Ø5.
Installation A.3 5.0 2.
Installation B.1 B.2 Ø5.
Installation B.3 5.0 ① ② ③ 2.
Installation A.3 B.3 2.2 5.
Installation 2.3 Ø 5≤Ø≤6.5 6.
Installation 2.
Installation 2.5 2.6 2.
Installation 2.6 5.
Installation 3.
Installation 3.
Installation 3.
Installation 3.4 5.
Installation 3.5 4.1 4.
Installation 4.
Installation 4.2 0°-355° 4.
Installation 5.
Installation 5.
Installation 5.
Operation Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
Operation Reset and Restore Camera Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. For the position of the reset button, refer to the figure in the interface introduction page.
UD16444B