Bullet Network Camera Quick Start Guide COPYRIGHT © 2018 Hikvision.
Quick Start Guide ALL RIGHTS RESERVED Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
e f l Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. Power Supply The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the Limited Power Source.
A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details. Cleaning Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do not use alkaline detergents. Using Environment When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.
Set up camera time manually for the first time access if the local time is not synchronized with that of the network. Visit the camera via Web browse/client software and go to time settings interface. White Light Illuminator (If supported) The white suppliment light source of the camera is classified as Risk Group 2 (RG2). Possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be harmful to the eyes.
Make sure that the power has been disconnected before you wire, install, or disassemble the device. Make sure that no reflective surface is too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. Symbols and Marks Notice Warning Forbidden Correct Incorrect Turn to page A and continue. i. Not necessarily included accessory. ii. Variable accessory amount. iii. Skip this step if not required.
Disposal Purchase separately Other situations Other situations omitted Waterproof Skip this step if not necessary Statement (for product with white light illuminator) The product should be positioned so that prolonged staring into its white light source at a distance closer than 3 m is not expected.
1x * 1x 4x * 1x 1x 1x * 1x 2x * 1x T20 T10 1x 1
1.
1.
2.1 A.1-A.5 B.1-B.
1 A.1 A.
A.3 Ø5.5mm Ø24mm A.
A.5 5.0 2.
B.1 B.
B.3 Ø5.5mm B.4 5.
B.5 2.
A.5 B.5 2.
2.3 5.
2.
2.
2.
2.
3.1 3.
3.
3.
3.
3.
4.1* For anti-corrosion models, you must apply anti-corrosion gel to the screws that are exposed to corrosive atmosphere.
4.
Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
UD10596B-A