Network Fisheye Camera Quick Start Guide UD02120B 0
Network Fisheye Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Fisheye Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Fisheye Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Fisheye Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Fisheye Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Fisheye Camera·Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
Network Fisheye Camera·Quick Start Guide malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Network Fisheye Camera·Quick Start Guide responsibility for problems caused by unauthorized repair or maintenance.
Network Fisheye Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Overview of Fisheye Camera ......................................... 10 1.2 Disassembling the Camera ............................................ 11 2 Installation .................................................................................... 13 2.1 Ceiling Mounting ........................................................... 14 2.
Network Fisheye Camera·Quick Start Guide 1 Appearance Description 1.
Network Fisheye Camera·Quick Start Guide Table 1-1 Description of Overview No. Description No. Description 1 Camera Body 6 Ethernet Interface 2 Reset 7 RS-485 Interface 3 Micro SD Card Slot 8 Power Interface 4 Camera Cover 9 Audio In 5 Alarm Interfaces 10 Audio Out 1.2 Disassembling the Camera Steps: 1. Loosen the lock screw on the camera cover. 2. Remove the camera cover, and you can see the oval dismountable sheet. 3. Loosen the two screws on the dismountable part. 4.
Network Fisheye Camera·Quick Start Guide Oval Sheet Figure 1-3 Move the Oval Sheet Aside Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Fisheye Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Fisheye Camera·Quick Start Guide 2.1 Ceiling Mounting Steps: 1. Drill three screw holes and the cable hole according to the supplied drill template. A 1 1 TOP Drill Template HoleA: for cables routed through the ceiling Screw hole 1: for Mounting Base 1 Figure 2-1 Drill Template 2. Fix the three supplied screws half-deep to the ceiling, leaving enough space to hook the camera body.
Network Fisheye Camera·Quick Start Guide 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Align the screw holes to the inserted screws, hook the camera body to the screws, and route the camera body to secure the camera with the screws. 5. Hammer the half-deep screws into the ceiling totally. 6. Install the camera cover to the camera body, and fix them by tightening the lock screw on the camera cover.
Network Fisheye Camera·Quick Start Guide 2.2 Wall Mounting with a Slant Mounting Base The wall mounting with a slant mounting base provides a wider surveillance view compared to the wall mounting. And you need to purchase a slant mounting base separately if this mounting method is selected. Steps: 1. Fix the slant mounting base to the wall with the screws. Figure 2-5 Fix the Slant Mounting Base 2. Screw the three screws half-deep to the mounting base.
Network Fisheye Camera·Quick Start Guide Figure 2-6 Hammer the Screws 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Align the screw holes to the inserted screws, hook the camera body to the screws, and route the camera body to secure the camera with the screws. 5. Screw the half-deep screws into the wall totally. 6. Install the camera cover to the camera body, and fix them by tightening the lock screw on the camera cover.
Network Fisheye Camera·Quick Start Guide Figure 2-7 Install the Camera Body and Cover Lock Screw Figure 2-8 Tighten the Lock Screw on the Camera Cover 18
Network Fisheye Camera·Quick Start Guide 2.3 Wall Mounting with a Junction Box You have to purchase a junction box separately if this mounting method is selected. Steps: 1. Fix the junction box to the wall with screws. Figure 2-9 Fix the Junction Box 2. Screw the three supplied screws half-deep to the junction box. 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4.
Network Fisheye Camera·Quick Start Guide Figure 2-10 Install the Camera Body and Cover Lock Screw Figure 2-11 Tighten the Lock Screw on the Camera Cover 2.
Network Fisheye Camera·Quick Start Guide You have to purchase the bracket separately if this mounting method is selected. 1. Install the bracket to the wall. 2. Install the mounting base to the bracket. 3. Screw the three supplied screws half-deep to the mounting base. Figure 2-12 Install the Bracket 4. Connect the corresponding power cable, network cable, audio and alarm cables. 5.
Network Fisheye Camera·Quick Start Guide Figure 2-13 Install the Camera Body and Cover Figure 2-14 Tighten the Screw on the Camera Cover 22
Network Fisheye Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network Fisheye Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Fisheye Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Fisheye Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password.
Network Fisheye Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click Activate to start activation.
Network Fisheye Camera·Quick Start Guide 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the admin password and click Modify to activate your IP address modification.
Network Fisheye Camera·Quick Start Guide The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Fisheye Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Fisheye Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 1-1 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
0