Network Fisheye Camera User Manual UD14558B
User Manual of Network Fisheye Camera User Manual COPYRIGHT ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
User Manual of Network Fisheye Camera FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
User Manual of Network Fisheye Camera residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
User Manual of Network Fisheye Camera 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
User Manual of Network Fisheye Camera to all the local codes. Please install blackouts equipment into the power supply circuit for convenient supply interruption. Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself.
User Manual of Network Fisheye Camera Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type. Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection: Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished.
User Manual of Network Fisheye Camera Table of Contents Chapter 1 System Requirement ................................................................................ 1 Chapter 2 Network Connection ................................................................................ 2 2.1 Setting the Network Camera over the LAN ........................................................ 2 2.1.1 Wiring over the LAN ...................................................................................................
User Manual of Network Fisheye Camera 5.5 User Management ......................................................................................... 42 5.5.1 User Management .......................................................................................................... 42 5.5.2 Online Users .................................................................................................................... 44 Chapter 6 Network Settings .........................................................
User Manual of Network Fisheye Camera 9.6 Configuring Audio Exception Detection ........................................................... 92 9.7 Configuring Intrusion Detection ...................................................................... 94 9.8 Configuring Line Crossing Detection ................................................................ 96 9.9 Configuring Region Entrance Detection ........................................................... 98 9.
User Manual of Network Fisheye Camera Chapter 1 System Requirement Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.
User Manual of Network Fisheye Camera Chapter 2 Network Connection Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.
User Manual of Network Fisheye Camera Refer to the Figure 2-2 to set network camera over the LAN via a switch or a router. Figure 2-1 Connecting Directly Figure 2-2 Connecting via a Switch or a Router 2.1.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. Activation via Web Browser Steps: 1.
User Manual of Network Fisheye Camera Figure 2-3 Activation via Web Browser 3. Create a password and input the password into the password field. A password with user name in it is not allowed. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
User Manual of Network Fisheye Camera Select inactive device. Input and confirm password. Figure 2-4 SADP Interface Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.
User Manual of Network Fisheye Camera 5. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 2-5 Modify the IP Address 6. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
User Manual of Network Fisheye Camera Figure 2-6 Control Panel 2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below.
User Manual of Network Fisheye Camera 3. Check the device status from the device list, and select an inactive device. 4. Click the Activate button to pop up the Activation interface. 5. Create a password and input the password in the password field, and confirm the password.
User Manual of Network Fisheye Camera Figure 2-9 Modifying the Network Parameters 8. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. 9. Input the password to activate your IP address modification. 2.2 Setting the Network Camera over the WAN Purpose: This section explains how to connect the network camera to the WAN with a static IP or a dynamic IP. 2.2.
User Manual of Network Fisheye Camera 2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3. Save the static IP in the router. 4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port mapping vary according to the different routers. Please call the router manufacturer for assistance with port mapping. Note: Refer to Appendix 2 for detailed information about port mapping. 5.
User Manual of Network Fisheye Camera 1. Connect the network camera to the router. 2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3. In the router, set the PPPoE user name, password and confirm the password. 4. Set port mapping. E.g. 80, 8000, and 554 ports. The steps for port mapping vary depending on different routers. Please call the router manufacturer for assistance with port mapping.
User Manual of Network Fisheye Camera Figure 2-13 Normal Domain Name Resolution Steps: 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section 5.3.4 Configuring DDNS Settings for detailed configuration. 3. Visit the camera via the applied domain name.
User Manual of Network Fisheye Camera Chapter 3 Access to the Network Camera 3.1 Accessing by Web Browsers Note: For certain camera models, HTTPS is enabled by default and the camera creates an unsigned certificate automatically. When you access to the camera the first time, the web browser prompts a notification about the certificate issue. To cancel the notification, install a signed-certificate to the camera. For detailed operation, see 6.2.5 HTTPS Settings. Steps: 1. Open the web browser. 2.
User Manual of Network Fisheye Camera 4. Click Login. 5. (Optional) Install the plug-in before viewing the live video and operating the camera. Follow the installation prompts to install the plug-in. Note: For camera that supports plug-in free live view, if you are using Google Chrome 45 and its above version or Mozilla Firefox 52 and its above version, plug-in installation is not required. But Picture and Playback functions are hidden.
User Manual of Network Fisheye Camera Figure 3-3 iVMS-4200 Main View Note: For detailed information about the software, please refer to the user manual of the iVMS-4200 Client Software.
User Manual of Network Fisheye Camera Chapter 4 Live View 4.1 Live View Page Purpose: The live view page allows you to view the real-time video, capture images, realize PTZ control, set/call presets and configure video parameters. Log in the network camera to enter the live view page, or you can click Live View on the menu bar of the main page to enter the live view page. Note: You can also visit the fisheye camera to get the live view in different live view modes via iVMS-4200 client software.
User Manual of Network Fisheye Camera Menu Bar PTZ Control Display Control Live View Window Tool Bar Preset/Patrol Setting Figure 4-2 Live View Page (Hardware Decoding) Menu Bar: Click the tab to enter Live View, Playback, Picture, Application and Configuration page respectively. Display Control: The display control area allows you to select decoding mode, mount type and display mode of live view. Software decoding and hardware decoding are selectable for decoding mode.
User Manual of Network Fisheye Camera Table 4-1 Description of Mount Types Mount Type Icon Description Ceiling mounting. Wall mounting. Table mounting. Display Mode You can select a display mode for the layout of the live view window. The description of each display mode is shown in the following table. Fisheye View: In the Fisheye View mode, the whole wide-angle view of the fisheye camera is displayed. This view mode is called Fisheye View because it approximates the vision of a fish’s convex eye.
User Manual of Network Fisheye Camera Mode Description Mode Description Live view with 1 fisheye view and 3 PTZ views. Live view with into 4 PTZ views. Live view with 1 fisheye view and 8 PTZ views. Live view with a panorama view and 3 PTZ views. Live view with a fisheye view, a panorama view and 3 PTZ views. Live view with a AR hemisphere view Live view with a 4 PTZ fusion view Panorama view. Live view with a panorama view and 3 PTZ views.
User Manual of Network Fisheye Camera Note: Selectable stream types may be different between camera channels under different display modes. Detailed information is shown in the following table. Live View Window: Display the live video on the display window of live view. Toolbar: Start/Stop the live view, enable/disable the two-way audio, adjust the audio volume, capture pictures, record the video files, etc. Note: Icons on tool bar are different under different decoding mode.
User Manual of Network Fisheye Camera Figure 4-3 Live View Interface (Software Decoding) Figure 4-4 Live View Interface (Hardware Decoding) Table 4-4 Descriptions of Live View Icons Icon Description Start all live view. Stop all live view. Set aspect ratio as 4:3. Icon Description Set aspect ratio as 16:9. Window size for original video stream. Self-adaptive window size. Window division, 1x1. Window division, 2x2. Window division, 3x3. / Manually start/stop recording.
User Manual of Network Fisheye Camera Audio on and adjust the volume. Mute. / Start/stop two-way audio. / Start/stop digital zoom). Manually capture a picture. Full screen. Show/hide the PTZ panel. / Notes: Toolbar icons on the live view page vary according to decoding modes and camera models. Digital Zoom: 1) Click to start the function. 2) Click the mouse on the live view image and drag it to a lower right position. The area in the red rectangle will be zoomed in after you release the mouse.
User Manual of Network Fisheye Camera right of the window to realize pan/tilt/zoom control of the PTZ View. PTZ View Navigation Box Figure 4-5 PTZ Control Note: If Fisheye View or Panorama View is selected for live view together with the PTZ View, when you click on a random PTZ view, a navigation box indicating the location of the PTZ view will be shown on the fisheye or panorama view. See Figure 4-5. 4.4.
User Manual of Network Fisheye Camera Figure 4-6 PTZ Control Panel Table 4-5 Descriptions of PTZ Control Panel Icon Description Direction buttons Start/stop auto scan / Zoom out/Zoom in Focus -/Focus + Iris -/Iris + Adjust speed of pan/tilt movements Enable/disable light Auxiliary Focus Enable/disable wiper Lens initialization Start manual tracking Start 3D zoom Click to set presets Click to set patrol Steps: 1.
User Manual of Network Fisheye Camera 5. (Optional) you can click on other buttons to realize corresponding functions. 4.4.2 Setting/Calling/Deleting a Preset Setting a Preset: Purpose: A preset for the fisheye camera is a predefined PTZ View which contains information of pan, tilt, focus and other parameters. Steps: 1. Click to select a PTZ View on the display window. 2. Click the direction/zoom buttons on the PTZ Control panel to adjust the PTZ View as desired. 3.
User Manual of Network Fisheye Camera The PTZ View of the fisheye camera can directly and quickly move to the area of interest, which is defined as a preset. Before you start: Set the preset. The icons ( , and ) will appear on the preset list. Steps: 1. Click to select a PTZ View on the display window. 2. Select the preset number from the list. 3. Click the icon to call the selected preset. The selected PTZ View will move to the pre-defined preset scene. Deleting a Preset Steps: 1.
User Manual of Network Fisheye Camera Figure 4-8 Patrol Configuration (1) 2. Select a path No. from the drop-down list, and click the icon to configure patrol path. 3. Click to add a preset into the path, and click to delete a preset. 4. Set the preset number, speed and lingering time at each preset. You can adjust the order of presets by using and . Figure 4-9 Patrol Configuration (2) 5. Click OK to save patrol path.
User Manual of Network Fisheye Camera Chapter 5 Network Configuration Camera 5.1 Configuring Local Parameters Purpose: The local configuration refers to the parameters of the live view, record files and captured pictures. The record files and captured pictures are the ones you record and capture using the web browser and thus the saving paths of them are on the PC running the browser. Steps: 1. Enter the Local Configuration interface: Configuration > Local. 2.
User Manual of Network Fisheye Camera Display POS Information: Enable the function, feature information of the detected target is dynamically displayed near the target in the live image. The feature information of different functions are different. For example, ID and waiting time for Queue Management, height for People Counting, etc. Note: Display POS Information is only available for certain camera models. Image Format: Choose the image format for picture capture.
User Manual of Network Fisheye Camera 3. Click Save to save the settings. 5.2 Configure System Settings Purpose: Follow the instructions below to configure the system settings, include System Settings, Maintenance, Security, and User Management, etc. 5.2.1 Configuring Basic Information Enter the Device Information interface: Configuration > System > System Settings > Basic Information. In the Basic Information interface, you can edit the Device Name and Device No.
User Manual of Network Fisheye Camera Figure 5-2 Time Settings 2. Select the Time Zone of your location from the drop-down menu. 3. Configure the NTP settings. (1) Click to enable the NTP function. (2) Configure the following settings: Server Address: IP address of NTP server. NTP Port: Port of NTP server. Interval: The time interval between the two synchronizing actions with NTP server. (3) (Optional) You can click the Test button to test the time synchronization function via NTP server.
User Manual of Network Fisheye Camera Note: If the camera is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the camera is set in a customized network, NTP software can be used to establish a NTP server for time synchronization. Configure the manual time synchronization. (1) Check the Manual Time Sync. item to enable the manual time synchronization function.
User Manual of Network Fisheye Camera 1. Enter RS232 Port Setting interface: Configuration > System > System Settings > RS232. 2. Configure the Baud Rate, Data Bit, Stop Bit, Parity, Flow Control, and Usage. Figure 5-5 RS232 Settings Note: If you want to connect the camera by the RS232 port, the parameters of the RS232 should be exactly the same with the parameters you configured here. 3. Click Save to save the settings. 5.2.
User Manual of Network Fisheye Camera Figure 5-6 RS-485 Settings 2. Set the RS485 parameters and click Save to save the settings. By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop bit is 1 and the Parity and Flow Control is None. Note: The Baud Rate, PTZ Protocol and PTZ Address parameters should be exactly the same as the PTZ camera parameters. 5.2.
User Manual of Network Fisheye Camera Figure 5-7 DST Settings 2. Select the start time and the end time. 3. Select the DST Bias. 4. Click Save to activate the settings. 5.2.6 Configuring Metadata Settings Purpose: Metadata is the raw data the camera collects before algorithm processing. Metadata of intrusion detection, line crossing detection, region entrance detection, region exiting detection, unattended baggage detection, object removal, queue management and face capture are supported.
User Manual of Network Fisheye Camera image by default. If the region is configured in the face capture settings, the camera detects the configured region. 5.2.7 Open Source Software License Information about the open source software that applies to the IP camera can be checked if required. Go to Configuration > System Settings > About. 5.3 Maintenance 5.3.
User Manual of Network Fisheye Camera encryption password is required when you import the file to other cameras. Diagnose Information: click to download log and system information. Import Config. File Configuration file is used for the batch configuration of the cameras. Steps: 1. Click Browse to select the saved configuration file. 2. Click Import and input the encryption password that you set during exporting. Note: You need to reboot the camera after importing configuration file.
User Manual of Network Fisheye Camera Figure 5-8 Log Searching Interface 2. Set the log search conditions to specify the search, including the Major Type, Minor Type, Start Time and End Time. 3. Click Search to search log files. The matched log files will be displayed on the log list interface. Figure 5-9 Log Searching 4. To export the log files, click Export to save the log files. 5.
User Manual of Network Fisheye Camera 5.4.1 Authentication Purpose: You can specifically secure the stream data of live view. Steps: 1. Enter the Authentication interface: Configuration > System > Security > Authentication. Figure 5-10 Authentication 2. Set up authentication method for RTSP authentication and WEB authentication. Caution: Digest is the recommended authentication method for better data security. You must be aware of the risk if you adopt basic as the authentication method. 3.
User Manual of Network Fisheye Camera Figure 5-11 IP Address Filter Interface 2. Check the checkbox of Enable IP Address Filter. 3. Select the type of IP Address Filter in the drop-down list, Forbidden and Allowed are selectable. 4. Set the IP Address Filter list. Add an IP Address Steps: (1) Click the Add to add an IP. (2) Input the IP Adreess. Figure 5-12 Add an IP (3) Click the OK to finish adding. Modify an IP Address Steps: (1) Left-click an IP address from filter list and click Modify.
User Manual of Network Fisheye Camera Figure 5-13 Modify an IP (3) Click the OK to finish modifying. Delete an IP Address or IP Addresses. Select the IP address(es) and click Delete. 5. Click Save to save the settings. 5.4.3 Security Service To enable the remote login, and improve the data communication security, the camera provides the security service for better user experience. Steps: 1. Enter the security service configuration interface: Configuration > System > Security > Security Service.
User Manual of Network Fisheye Camera 5.5 User Management 5.5.1 User Management As Administrator The admin user can add, delete or modify user accounts, and grant them different permissions. We highly recommend you manage the user accounts and permissions properly. Enter the User Management interface: Configuration > System > User Management Note: Admin password if required for adding and modifying a user account.
User Manual of Network Fisheye Camera STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
User Manual of Network Fisheye Camera 2. Slide the slide bar to set the simultaneous login. If the number of the illegal login attempts exceeds the set threshold, your access will be denied. As Operator or User Operator or user can modify password. Old password is required for this action. 5.5.2 Online Users Purpose: You can see the current users who are visiting the device through this interface. User information, such as user name, level, IP address, and operation time, is displayed in the User List.
User Manual of Network Fisheye Camera Chapter 6 Network Settings Purpose: Follow the instructions in this chapter to configure the basic settings and advanced settings. 6.1 Configuring Basic Settings Purpose: You can configure the parameters, including TCP/IP, DDNS, PPPoE, Port, and NAT, etc., by following the instructions in this section. 6.1.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network.
User Manual of Network Fisheye Camera Figure 6-1 TCP/IP Settings 2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings and Multicast Address. 3. (Optional) Check the checkbox of Enable Multicast Discovery, and then the online network camera can be automatically detected by client software via private multicast protocol in the LAN. 4. Configure the DNS server.
User Manual of Network Fisheye Camera multicast group address. Before utilizing this function, you have to enable the Multicast function of your router. A reboot is required for the settings to take effect. 6.1.2 Configuring DDNS Settings Purpose: If your camera is set to use PPPoE as its default network connection, you can use the Dynamic DNS (DDNS) for network access. Before you start: Registration on the DDNS server is required before configuring the DDNS settings of the camera. Steps: 1.
User Manual of Network Fisheye Camera Figure 6-2 DynDNS Settings NO-IP: Steps: (1) Choose the DDNS Type as NO-IP. Figure 6-3 NO-IP DNS Settings (2) Enter the Server Address as www.noip.com (3) Enter the Domain name you registered. (4) Enter the User Name and Password. (5) Click Save and then you can view the camera with the domain name. Note: Reboot the device to make the settings take effect.
User Manual of Network Fisheye Camera 6.1.3 Configuring PPPoE Settings Steps: 1. Enter the PPPoE Settings interface: Configuration > Network > Basic Settings > PPPoE Figure 6-4 PPPoE Settings 2. Check the Enable PPPoE checkbox to enable this feature. 3. Enter User Name, Password, and Confirm password for PPPoE access. Note: The User Name and Password should be assigned by your ISP.
User Manual of Network Fisheye Camera 6.1.4 Configuring Port Settings Purpose: You can set the port No. of the camera, e.g., HTTP port, RTSP port and HTTPS port. Steps: 1. Enter the Port Settings interface, Configuration > Network > Basic Settings > Port Figure 6-5 Port Settings 2. Set the ports of the camera. HTTP Port: The default port number is 80, and it can be changed to any port No. which is not occupied. RTSP Port: The default port number is 554 and it can be changed to any port No.
User Manual of Network Fisheye Camera No. ranges from 1 to 65535. WebSockets Port: The default server port number is 7682. It can be changed to any port No. ranges from 1 to 65535. Note: WebSocket and WebSockets protocol are used for plug-in free live view. 3. Click Save to save the settings. Note: A reboot is required for the settings to take effect. 6.1.5 Configure NAT (Network Address Translation) Settings Purpose: NAT interface allows you to configure the UPnP™ parameters.
User Manual of Network Fisheye Camera Note: Only when the UPnP™ function is enabled, ports of the camera are active. 3. Choose a friendly name for the camera, or you can use the default name. 4. Select the port mapping mode. Manual and Auto are selectable. Note: If you select Auto, you should enable UPnP™ function on the router. If you select Manual, you can customize the value of the external port and complete port mapping settings on router manually. 5. Click Save to save the settings. 6.
User Manual of Network Fisheye Camera For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers and special characters) in order to increase the security of your product.
User Manual of Network Fisheye Camera Figure 6-7 SNMP Settings 2. Check the checkbox of Enable SNMPv1, Enable SNMP v2c, Enable SNMPv3 to enable the feature correspondingly. 3. Configure the SNMP settings.
User Manual of Network Fisheye Camera configure here. 4. Click Save to save and finish the settings. Notes: • A reboot is required for the settings to take effect. • To lower the risk of information leakage, you are suggested to enable SNMP v3 instead of SNMP v1 or v2. 6.2.2 Configuring FTP Settings Purpose: You can configure the FTP server related information to enable the uploading of the captured pictures to the FTP server. The captured pictures can be triggered by events or a timing snapshot task.
User Manual of Network Fisheye Camera For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers and special characters) in order to increase the security of your product.
User Manual of Network Fisheye Camera Note: The anonymous access function must be supported by the FTP server. 6. Click Save to save the settings. 6.2.3 Configuring Email Settings Purpose: The system can be configured to send an Email notification to all designated receivers if an alarm event is detected, e.g., motion detection event, video loss, video tampering, etc.
User Manual of Network Fisheye Camera SSL or TLS and enable STARTTLS, emails will be sent after encrypted by STARTTLS, and the SMTP port should be set as 25. Note: If you want to use STARTTLS, make sure that the protocol is supported by your e-mail server. If you check the Enable STARTTLS checkbox when the protocol is not supported by your e-mail sever, your e-mail will not be encrypted. Attached Image: Check the checkbox of Attached Image if you want to send emails with attached alarm images.
User Manual of Network Fisheye Camera Figure 6-9 Email Settings 4. Click Save to save the settings. 6.2.4 Platform Access Purpose: Platform access provides you an option to manage the devices via platform. Steps: 1. Enter the Platform Access settings interface: Configuration > Network > Advanced Settings > Platform Access 2. Check the checkbox of Enable to enable the platform access function of the device. 3. Select the Platform Access Mode. Note: Hik-Connect is an application for mobile devices.
User Manual of Network Fisheye Camera If you select Platform Access Mode as Hik-Connect, 1) Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 2) Create a verification code or change the verification code for the camera. Note: • The verification code is required when you add the camera to Hik-Connect app. • For more information about the Hik-Connect app, refer to Hik-Connect Mobile Client User Manual. 3) You can use the default server address.
User Manual of Network Fisheye Camera Figure 6-10 HTTPS Configuration Interface 4. Create the self-signed certificate or authorized certificate. Figure 6-11 Create Self-signed Certificate Create the self-signed certificate (1) Select Create Self-signed Certificate as the Installation Method. (2) Click Create button to enter the creation interface. (3) Enter the country, host name/IP, validity and other information. (4) Click OK to save the settings.
User Manual of Network Fisheye Camera a) Select Signed certificate is available, Start the installation directly. Click Browse and Install to import the certificate to the device. Figure 6-12 Import the Certificate (1) b) Select Create the certificate request first and continue the installation. Click Browse and Install to import the certificate to the device. Figure 6-13 Import the Certificate (2) 5.
User Manual of Network Fisheye Camera Note: The exported certificate should be saved in the certificate folder of your client software before adding the device to your PC client. 7. Click the Save button to save the settings. 6.2.6 Configuring QoS Settings Purpose: QoS (Quality of Service) can help solve the network delay and network congestion by configuring the priority of data sending. Steps: 1.
User Manual of Network Fisheye Camera 6.2.7 Configuring 802.1X Settings Purpose: The IEEE 802.1X standard is supported by the network cameras, and when the feature is enabled, the camera data is secured and user authentication is needed when connecting the camera to the network protected by the IEEE 802.1X. Before you start: The authentication server must be configured. Please apply and register a user name and password for 802.1X in the server.
User Manual of Network Fisheye Camera 2. Check the Enable IEEE 802.1X checkbox to enable the feature. 3. Configure the 802.1X settings, including Protocol, EAPOL version, User Name, Password and Confirm. Note: The EAPOL version must be identical with that of the router or the switch. 4. Enter the user name and password to access the server. 5. Click Save to finish the settings. Note: A reboot is required for the settings to take effect. 6.2.
User Manual of Network Fisheye Camera 6.2.9 Configuring HTTP Listening Purpose: The camera can send alarm information to the destination IP or host name via HTTP protocol. If the network is disconnected, the data can be uploaded to the destination IP or host name after the network connection is normal. Before you start: The destination IP or host name should support the HTTP protocol to receive the alarm information. Steps: 1.
User Manual of Network Fisheye Camera Chapter 7 Video/Audio Settings Purpose: Follow the instructions below to configure the video setting, audio settings, ROI, Display info. on Stream, etc. 7.1 Configuring Video Settings For certain camera models, you can configure parameters for available video streams, for example, the main stream, the sub-stream, etc. Steps: 1. Enter the Video Settings interface, Configuration > Video/Audio > Video Figure 7-1 Video Settings 2. Select the Stream Type.
User Manual of Network Fisheye Camera Maintenance > System Service> Software to enable the function is required. • The main stream is usually for recording and live view with good bandwidth, and the sub-stream can be used for live view when the bandwidth is limited. 3. You can customize the following parameters for the selected stream type. Video Type: Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio.
User Manual of Network Fisheye Camera Note: Selectable video encoding types may vary according to different camera modes. H.264+ and H.265+: • H.264+: If you set the main stream as the stream type, and H.264 as the video encoding, you can see H.264+ available. H.264+ is an improved compression coding technology based on H.264. By enabling H.264+, users can estimate the HDD consumption by its maximum average bitrate. Compared to H.264, H.
User Manual of Network Fisheye Camera Max. Average Bitrate: When you set a maximum bitrate, its corresponding recommended maximum average bitrate will be shown in the Max. Average Bitrate box. You can also set the maximum average bitrate manually from 32 Kbps to the value of the set maximum bitrate. Profile: When you select H.264 or H.265 as video encoding, you can set the profile. Selectable profiles vary according to camera models. I Frame Interval: Set I Frame Interval from 1 to 400.
User Manual of Network Fisheye Camera Figure 7-2 Audio Settings 2. Configure the following settings. Note: Audio settings vary according to different camera models. Audio Encoding: G.722.1, G.711 ulaw, G.711alaw, G.726, MP2L2, PCM and MP3 are selectable. For MP2L2, the Sampling Rate and Audio Stream Bitrate are configurable. For PCM, the Sampling Rate can be set. Audio Input: MicIn and LineIn are selectable for the connected microphone and pickup respectively. Input Volume: 0-100 adjustable.
User Manual of Network Fisheye Camera Figure 7-3 Region of Interest Settings Steps: 1. Enter the ROI settings interface: Configuration > Video/Audio > ROI. 2. Select the Stream Type for ROI encoding. 3. Check the checkbox of Enable under Fixed Region item. 4. Set Fixed Region for ROI. (1) Select the Region No. from the drop-down list. (2) Check the Enable checkbox to enable ROI function for the chosen region. (3) Click Drawing.
User Manual of Network Fisheye Camera (4) Select the ROI level. (5) Enter a region name for the chosen region. (6) Click Save the save the settings of ROI settings for chosen fixed region. (7) Repeat steps (1) to (6) to setup other fixed regions. 7.4 Display Info. on Stream Check the checkbox of Enable Dual-VCA, and the information of the objects (e.g. human, vehicle, etc.) will be marked in the video stream.
User Manual of Network Fisheye Camera Chapter 8 Configuring Parameters Image 8.1 Configuring Display Settings Purpose: You can set the image quality of the camera, including brightness, contrast, saturation, sharpness, etc. Steps: 1. Enter the Display Settings interface: Configuration > Image> Display Settings 2. Set the image parameters of the camera. Note: In order to guarantee the image quality in the different illumination, it provides two sets of parameters for user to configure.
User Manual of Network Fisheye Camera Contrast describes the contrast of the image, which ranges from 1 to 100, and the default value is 50. Saturation describes the colorfulness of the image color, which ranges from 1 to 100, and the default value is 50. Sharpness describes the edge contrast of the image, which ranges from 1 to 100, and the default value is 50. Exposure Settings Iris Mode: If the camera is equipped with the fixed lens, only Manual is selectable, and the iris mode is not configurable.
User Manual of Network Fisheye Camera Smart Supplement Light: Smart Supplement Light function gives user an option to adjust the power of the IR LED, thus avoiding image over-exposure. When the light is turned on, and Auto and Manual are selectable for IR mode. Select AUTO, and the IR LED changes according to the actual luminance. E.g., if the current scene is bright enough, then the IR LED adjusts itself to lower power; and if the scene is not bright enough, the IR LED adjusts itself to higher power.
User Manual of Network Fisheye Camera Video Standard: 50 Hz and 60 Hz are selectable. Choose according to the different video standards. Normally, 50 Hz is for PAL standard and 60 Hz for NTSC standard. Note: The display parameters vary according to the different camera model. Please refer to the actual interface for details.
User Manual of Network Fisheye Camera 8.2 Configuring OSD Settings Purpose: OSD (On-screen Display) refers to the camera name, time/date format, display mode, and OSD size displayed on the live view. Steps: 1. Enter the OSD Settings interface: Configuration > Image > OSD Settings Figure 8-3 OSD Settings 2. Select a camera channel to configure. 3. Check the corresponding checkbox to select the display of camera name, date or week if required. 4. Edit the camera name in the text field of Camera Name. 5.
User Manual of Network Fisheye Camera • Up to 8 texts are configurable. • Text overlay is only supported when the live view stream is decoded by hardware and display mode is Fisheye View. 7. Adjust the position and alignment of text frames. Left align, right align and custom are selectable. If you select custom, you can use the mouse to click and drag text frames in the live view window to adjust their positions. Note: The alignment adjustment is only applicable to Text Overlay items. 8.
User Manual of Network Fisheye Camera Figure 8-4 Privacy Mask Settings 2. Select a camera channel to configure. 3. Check the checkbox of Enable Privacy Mask to enable this function. 4. Click the Draw Area button to start drawing. 5. Click-and-drag the mouse in the live video window to draw the mask area. 6. Click Stop Drawing to finish drawing. 7. You can click Clear All to clear all the configured privacy masks. 8. Click Save to save the settings. Note: Up to 4 privacy masks are configurable. 8.
User Manual of Network Fisheye Camera Overlay. Figure 8-5 Picture Overlay 2. Click Browse to select a picture. 3. Click Upload to upload it. 4. Check Enable Picture Overlay checkbox to enable the function. 5. Drag the red rectangle to adjust the position. 6. Click Save to save settings. Note: The picture must be in RGB24 bmp format and the maximum picture size is 128*128.
User Manual of Network Fisheye Camera Chapter 9 Configuring Settings Event This section explains how to configure the network camera to respond to alarm events, including motion detection, video tampering, alarm input, alarm output, exception, exception detection, intrusion detection, and line crossing detection, etc. These events can trigger the linkage methods, such as Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
User Manual of Network Fisheye Camera Figure 9-1 Motion Detection Settings 2. Check the checkbox of Enable Motion Detection. 3. (Optional) Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles on the live view window. Note: You can go to Configuration > Local Configuration > Live View Parameters, and then select Disable for Rules if you don’t want the detected objected displayed with the rectangles. 4. Click Draw Area.
User Manual of Network Fisheye Camera 6. (Optional) Move the slider to set the sensitivity of the detection. Task 2: Set the Arming Schedule for Motion Detection Steps: 1. Click Arming Schedule to edit the arming schedule. Figure 9-2 Arming Schedule Setting 2. Click on the time bar and drag the mouse to select the time period. Note: Click on the selected time period, you can adjust the time period to the desired time by either moving the time bar or input the exact time period. 3.
User Manual of Network Fisheye Camera Figure 9-3 Linkage Method Settings Audible Warning Trigger the audible warning locally. And it only supported by the device that has the audio output. Notify Surveillance Center: Send an exception or alarm signal to remote management software when an event occurs. Send Email: Send an email with alarm information to a user or users when an event occurs. Note: To send the Email when an event occurs, please refer to Section 5.3.8 to complete Email setup in advance.
User Manual of Network Fisheye Camera Smart Tracking: It can make the speed dome to track target manually by clicking the target on the live view of fisheye camera. Note: In order to make smart tracking take effect, you need to have a speed dome which has auto tracking function installed near your fisheye camera, and you have to configure relevant settings on 4200 Client Software. Refer to the user manual of 4200 Client Software for detailed information.
User Manual of Network Fisheye Camera supported area number varies according to different camera models. (2) Select OFF for Switch Day and Night Settings. (3) Select the area by clicking the area No.. (4) Slide the cursor to adjust the sensitivity and proportion of object in the area for the selected area. Sensitivity: The greater the value is, the easier the alarm will be triggered.
User Manual of Network Fisheye Camera (2) Select Scheduled-Switch for Switch Day and Night Settings. (3) Select the start time and end time for the switching timing. (4) Select the area by clicking the area No.. (5) Slide the cursor to adjust the sensitivity and proportion of object in the area for the selected area in the daytime. (6) Slide the cursor to adjust the sensitivity and proportion of object in the area for the selected area at night.
User Manual of Network Fisheye Camera Figure 9-5 Video Tampering Detection Settings 3. Draw the detection area as in the normal configuration mode. 4. Move the slider to set the sensitivity. 5. Click Arming Schedule to set arming schedule as that in Task 2 Set the Arming Schedule for Motion Detection in Section 5.6.1. 6. Click Linkage Method to set linkage method as that in Task 3 Set the Linkage Method for Motion Detection in Section 5.6.1. 7. Click Save to save the settings. 9.
User Manual of Network Fisheye Camera Figure 9-6 Alarm Input Settings 2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). Edit the alarm name (optional). 3. Check the checkbox of Enable Alarm Input Handling to enable the function. 4. Set the arming schedule. Refer to Task 2: Set Arming Schedule for Motion Detection in Section 5.6.1. 5. Set the linkage method. Refer to Task 3: Set Linkage Method for Motion Detection in Section 5.6.1. 6.
User Manual of Network Fisheye Camera 1. Enter the Alarm Output Settings interface: Configuration > Events > Basic Event > Alarm Output 2. Select one alarm output channel in the Alarm Output drop-down list. 3. (Optional) Input the alarm output name in the text field. 4. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 5. Set the arming schedule.
User Manual of Network Fisheye Camera Note: Alarm output settings vary according to the camera model. 9.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the cameras. Steps: 1. Enter the Exception Settings interface: Configuration > Event > Basic Event > Exception 2. Check the checkbox to select the linkage method taken for exception. For details, refer to Task 3: Set Linkage Method for Motion Detection in Section 5.6.1.
User Manual of Network Fisheye Camera Figure 9-9 Audio Exception Detection 2. Check the checkbox of Audio Loss Exception to enable the audio loss detection function. 3. Check the checkbox of Sudden Increase of Sound Intensity Detection to detect the sound steep rise in the surveillance scene. You can set the detection sensitivity and threshold for sound steep rise. 4. Check the checkbox of Sudden Decrease of Sound Intensity Detection to detect the sound steep drop in the surveillance scene.
User Manual of Network Fisheye Camera including Notify Surveillance Center, Send Email, Upload to FTP/Memory Card/NAS, Trigger Channel for recording and Trigger Alarm Output. 7. Click Save to save the settings. 9.7 Configuring Intrusion Detection Purpose: Intrusion detection function detects people, vehicle or other objects which enter and loiter in a pre-defined virtual region, and some certain actions can be taken when the alarm is triggered.
User Manual of Network Fisheye Camera 2. Check the checkbox of Enable to enable the function. 3. Select a region number from the drop-down list of Region. Region: A pre-defined vertexes area on the live view image. Targets, such as, people, vehicle or other objects, who enter and loiter in the region will be detected and trigger the set alarm. 4. Click Area Settings tab and click Draw Area button to start the region drawing. 5.
User Manual of Network Fisheye Camera 10. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 11. Click Arming Schedule to set the arming schedule. 12. Click Linkage Method to select the linkage methods for intrusion detection, including Notify Surveillance Center, Send Email, Upload to FTP/Memory Card/NAS, Trigger Channel and Trigger Alarm Output. 13. Click Save to save the settings. 9.
User Manual of Network Fisheye Camera Figure 9-11 Line Crossing Detection 2. Check the checkbox of Enable to enable the function. 3. Select the line from the drop-down list. 4. Click Area Settings tab and click Draw Area button, and a virtual line is displayed on the live video. 5. Drag the line, and you can locate it on the live video as desired. Click on the line, two red squares are displayed on each end, and you can click-and-drag one of the red squares to define the shape and length of the line. 6.
User Manual of Network Fisheye Camera as A<->B, A ->B, and B->A. A<->B: The object going across the plane with both directions can be detected and alarms are triggered. A->B: Only the object crossing the configured line from the A side to the B side can be detected. B->A: Only the object crossing the configured line from the B side to the A side can be detected. 8. Click Stop Drawing when finish drawing. 9. Drag the slider to set the sensitivity value. Sensitivity: Range [1-100].
User Manual of Network Fisheye Camera enter a pre-defined virtual region from the outside place, and some certain actions can be taken when the alarm is triggered. Steps: 1. Enter the Region Entrance Detection settings interface, Configuration > Event > Smart Event > Region Entrance Detection. Figure 9-12 Region Entrance Detection 2. Check the Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4.
User Manual of Network Fisheye Camera Min. Size: The minimum size of a valid target. Targets with smaller sizes would not trigger detection. 7. Click Stop Drawing when finish drawing. 8. Drag the slider to set the sensitivity value. Sensitivity: Range [1-100]. Sensitivity stands for the percentage of the body part of an acceptable target that enters the pre-defined region.
User Manual of Network Fisheye Camera Figure 9-13 Region Exiting Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and click Draw Area button to start the area drawing. 5. Click on the live video to specify the four vertexes of the detection region, and right click to complete drawing. 6. Set the Max. Size and Min. Size for valid targets.
User Manual of Network Fisheye Camera of an acceptable target that exits the pre-defined region. Sensitivity = 100 – S1/ST*100 S1 stands for the target body part that exits the pre-defined region. ST stands for the complete target body. Example: if you set the value as 60, the action can be counted as a region exiting action only when 40 percent body part exits the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9.
User Manual of Network Fisheye Camera Figure 9-14 Unattended Baggage Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and click Draw Area to start the area drawing. 5. Click on the live video to specify the four vertexes of the detection region, and right click to complete drawing. 6. Set the Max. Size and Min. Size for valid targets.
User Manual of Network Fisheye Camera Threshold: Range [5-100s], the threshold for the time of the objects left over in the region. If you set the value as 10, alarm is triggered after the object is left and stay in the region for 10s. 9. Drag the slider to set the sensitivity value. Sensitivity: Range [1-100]. Sensitivity stands for the percentage of the body part of an acceptable target that enters the pre-defined region.
User Manual of Network Fisheye Camera Figure 9-15 Object Removal Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and click Draw Area button to start the area drawing. 5. Click on the live video to specify the four vertexes of the detection region, and right click to complete drawing. 6. Set the Max. Size and Min. Size for valid targets.
User Manual of Network Fisheye Camera Threshold: Range [5-100s], the threshold for the time of the objects removed from the region. If you set the value as 10, alarm is triggered after the object disappears from the region for 10s. 9. Drag the slider to set the sensitivity value. Sensitivity: Range [1-100]. It stands for the percentage of the body part of an acceptable target that leaves the pre-defined region.
User Manual of Network Fisheye Camera Chapter 10 Storage Settings 10.1 Configuring Recording Schedule Purpose: There are two kinds of recording for the cameras: manual recording and scheduled recording. For the manual recording, refer to Section 4.3 Recording and Capturing Pictures Manually. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are stored in the SD card (if supported) or in the network disk. Steps: 1.
User Manual of Network Fisheye Camera Figure 10-2 Record Parameters Pre-record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the camera starts to record at 9:59:55. The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15 s, 20 s, 25 s, 30 s or not limited. Post-record: The time you set to stop recording after the scheduled time or the event.
User Manual of Network Fisheye Camera Record Triggered by Motion Detection If you select Motion, the video will be recorded when the motion is detected. Besides configuring the recording schedule, you have to set the motion detection area and check the checkbox of Trigger Channel in the Linkage Method of Motion Detection Settings interface. For detailed information, please refer to Section 5.6.1 Configuring Motion Detection.
User Manual of Network Fisheye Camera and check the checkbox of Trigger Channel in the Linkage Method of Line Crossing Detection Settings interface. For detailed information, please refer to Section 5.6.6 Configuring Line Crossing Detection. Record Triggered by Intrusion Detection If you select Intrusion Detection, the video will be recorded when the intrusion event is detected.
User Manual of Network Fisheye Camera 10.2 Configuring Capture Setting Purpose: You can configure the scheduled capture and event-triggered capture. The captured picture can be stored in the SD card (if supported) or in the network disk (For details, please refer to Section 6.3 Configuring Net HDD). The captured pictures can also be uploaded to a FTP server. Steps: 1. Enter Capture setting interface: Configuration > Storage > Schedule Setting 2.
User Manual of Network Fisheye Camera the events, including motion detection, alarm input, line crossing detection and intrusion detection. For details, please refer to Section 5.6. (4) Select the picture format, resolution, quality, capture interval, and capture number. 5. Set the time interval between two snapshots. 6. Click Save to save the settings. 7. (Optional) To upload the captured pictures to the FTP server, configure the FTP parameters and check Upload Picture checkbox in FTP Settings interface.
User Manual of Network Fisheye Camera Note: Please refer to the NAS User Manual for creating the file path. For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices.
User Manual of Network Fisheye Camera When the initialization completed, the status of disk will become Normal. Figure 10-7 View Disk Status 3. Define the quota for record and pictures. (1) Input the quota percentage for picture and for record. (2) Click Save and refresh the browser page to activate the settings. Figure 10-8 Quota Settings Notes: Up to 8 NAS disks can be connected to the camera.
User Manual of Network Fisheye Camera Chapter 11 People Counting To complete the configuration, you should: Set up counting rule. Set up data uploading. Set up advanced parameters. 11.1 Rule Settings Rule setting is compulsory for proper functioning of the camera. 11.1.1 Rule Steps: 1. Enter the Configuration interface: Configuration > People Counting. 2. Check Enable People Counting checkbox to enable the function. 3. Click on the left of the live view image and draw a red count area. 4.
User Manual of Network Fisheye Camera 11.1.2 Arming Schedule Steps: 1. Click Arming Schedule to edit the arming schedule. 2. Click on the time bar and drag the mouse to select the time period. Figure 11-1 Arming Schedule Note: Click on the selected time period, you can adjust the time period to the desired time by either moving the time bar or input the exact time period. 3. (Optional) Click Delete to delete the current arming schedule, or click Save to save the settings. 4.
User Manual of Network Fisheye Camera Figure 11-2 Linkage Method Notify Surveillance Center Send an exception or alarm signal to remote management software when an event occurs. 11.2 Data Uploading Setting Data uploading is about how and when the counting data can be sent to clients and users. You can upload people counting data to surveillance center and client software through SDK and HTTP (if configured). To upload real-time data, check the Real-Time Upload Data checkbox.
User Manual of Network Fisheye Camera Daily Reset Time You can set up a daily reset time. Or you can reset the counter manually by click Manual Reset.
User Manual of Network Fisheye Camera Chapter 12 Heat Map Heat map is a graphical representation of data represented by colors. The heat map function of the camera usually be used to analyze the visit times and dwell time of customers in a configured area. Steps: 1. Enter the Heat Map configuration interface: Configuration > Heat Map Configuration. 2. Check Enable Heat Map checkbox to enable the function. 3. Go to Area Settings to draw detection area. Click Draw Area to draw a detection area.
User Manual of Network Fisheye Camera 11. Click Save to save the settings. Note: The heat map statistics will be calculated under Application tab. Go to Application to check the heat map statistics.
User Manual of Network Fisheye Camera Chapter 13 Intersection Analysis Purpose: Intersection Analysis is used to monitor the human flow in an intersection-like scene. Note: The function varies according to different camera models. Steps: 1. Enter the Intersection Analysis configuration interface: Configuration > Intersection Analysis. 2. Check Enable Intersection Analysis checkbox to enable the function. 3. Set up rules. a) Go to Area Settings. b) Click Draw Area.
User Manual of Network Fisheye Camera Chapter 14 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Note: You can also search the records files and play it back in different playback modes via iVMS-4200 client software. Please refer to the User Manual of iVMS-4200 Client Software for detailed instructions. Steps: 1. Click Playback on the menu bar to enter playback interface. Figure 14-1 Playback Interface 2.
User Manual of Network Fisheye Camera Figure 14-2 Search Video 3. Choose a display mode to play the video. Figure 14-3 Playback Display Mode Setting Note: For detailed description of each display mode, refer to Section 4.1 Live View Page. 4. Click to play the video files found on this date. The toolbar on the bottom of Playback interface can be used to control playing process.
User Manual of Network Fisheye Camera Button Operation Button Operation Pause / Start/Stop clipping video files Stop Playback by frame Slow Forward / / Audio on and adjust volume/Mute Fast Forward Download Enable/Disable digital zoom Stop all playback Play with full screen Notes: You can set the local file saving path for the downloaded video files and pictures in Local Configuration interface. For details, please refer to Section 5.1.
User Manual of Network Fisheye Camera Chapter 15 Picture Click Picture to enter the picture searching interface. You can search, view, and download the pictures stored in the local storage or network storage. Notes: Make sure HDD, NAS or memory card are properly configured before you process picture searching. Make sure the capture schedule is configured. Go to Configuration > Storage > Schedule Settings > Capture to set the capture schedule. Figure 15-1 Picture Searching Interface Steps: 1.
User Manual of Network Fisheye Camera Chapter 16 Application Click Application to enter the heat map statistics interface. You can search, view, and download the counting data stored in the local storage or network storage. 16.1 People Counting Statistics After you enable the people counting function, you can view and download the people counting data from application tab. To get more intuitional results, you can display the data in different charts. Steps: 1. Select the report type.
User Manual of Network Fisheye Camera 16.2 Heat Map Statistics Purpose: Heat map is a graphical representation of data represented by colors. The heat map function of the camera usually be used to analyze the visit times and dwell time of customers in a configured area. To get more intuitional results, you can display the data in different charts. Before you start: You have to configure Heat Map setting before you can view and download the heat map data from application tab.
User Manual of Network Fisheye Camera Figure 16-2 Space Heat Map Time Heat Map: The heat value of the pre-defined area is calculated by hour, day, or month. You can click the Export button to export the data in an excel file. Figure 16-3 Time Heat Map Note: It is recommended that you do not adjust the electronic lens after the installation is completed, which may cause the inaccuracy of the data in some degree.
User Manual of Network Fisheye Camera 16.3 Intersection Analysis Statistics After you enable the intersection analysis function, you can view and download the intersection analysis data from application tab. To get more intuitional results, you can display the data in different charts. Steps: 1. Select a Flow In entrance. 2. Select the report type. Daily report, weekly report, monthly report, and annual report are selectable.
User Manual of Network Fisheye Camera Appendix Appendix 1 SADP Software Introduction Description of SADP SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool. It searches the active online devices within your subnet and displays the information of the devices. You can also modify the basic network information of the devices using this software.
User Manual of Network Fisheye Camera Search online devices manually You can also click Refresh button to refresh the online device list manually. The newly searched devices will be added to the list. You can click can click or on each column heading to order the information; you to expand the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. Modify network parameters Steps: 1.
User Manual of Network Fisheye Camera Appendix 2 Port Mapping The following settings are for TP-LINK router (TL-WR641G). The settings vary depending on different models of routers. Steps: 1. Select the WAN Connection Type, as shown below: Figure A.2.1 Select the WAN Connection Type 2. Set the LAN parameters of the router as in the following figure, including IP address and subnet mask settings. Figure A.2.2 Set the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding.
User Manual of Network Fisheye Camera another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2. Map the port 81, 8001, 555 and 8201 for the network camera at 192.168.1.24. 3. Enable ALL or TCP protocols. 4. Check the Enable checkbox and click Save. Figure A.2.3 Port Mapping Note: The port of the network camera cannot conflict with other ports.
User Manual of Network Fisheye Camera 134