Anti-Corrosion Network Dome Camera Quick Start Guide UD04336B 0504051070109 0
Network Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Dome Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Dome Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Dome Camera·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Network Dome Camera·Quick Start Guide Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Dome Camera·Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
Network Dome Camera·Quick Start Guide malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Dome Camera·Quick Start Guide responsibility for problems caused by unauthorized repair or maintenance.
Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 2 Installation .................................................................................... 12 2.1 Memory Card Installation .............................................. 13 2.2 Ceiling Mounting ........................................................... 13 2.3 Wall Mounting .............................................................. 16 2.
Network Dome Camera·Quick Start Guide 1 Appearance Description The overview of the anti-corrosion network dome camera is shown below: 1 Figure 1-1 Overview of Dome Camera (1) The overview of the components and the interfaces is shown below: 2 3 4 5 10 11 12 IN DC12V 8 6 7 9 Figure 1-2 Overview of Dome Camera (2) 10 13
Network Dome Camera·Quick Start Guide Table 1-1 Description of Overview ● No. 1 Description Bubble 2 3 Lens 4 5 Sealing Ring 6 7 Video Output Memory Card Slot 8 9 Reset Cable Sealing Ring 10 11 Network Interface Alarm Input and Output 12 13 Audio Input and Output Power Supply Black Liner Pedestal Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Dome Camera·Quick Start Guide 2 Installation Before you start ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Dome Camera·Quick Start Guide 2.1 Memory Card Installation This series of cameras support memory card installation. Installation steps are as follows. 1. Unscrew the three screws on the camera housing and remove the bubble. 2. Insert the memory card into the memory card slot until it clicks into place. 3. Replace and fix the bubble to finish memory card installation. Figure 2-1 Install the Memory Card 2.2 Ceiling Mounting Steps: 1.
Network Dome Camera·Quick Start Guide 1 Cable Outlet Drilling Template Screw hole 1:for Mounting Base Hole A:for cables routed through the ceiling 1 FRONT A 1 Figure 2-2 Drill Template 2. Fasten one third part of the screw into the drilled screw holes. Figure 2-3 Hammer the Screws 3. Align the three screws holes on the camera to the inserted screw, and rotate the camera clockwise to hook the camera on the screws.
Network Dome Camera·Quick Start Guide Screw Screw Screw Figure 2-4 Fix the Camera Pedestal 4. This series of camera supports 3-axis adjustment, and you can adjust the camera to the desired surveillance angle as the figure below. 0°~80° 0°~355° 0°~355° Figure 2-5 3-axis Adjustment 5. Tighten the three screws on the pedestal after the pedestal is installed.
Network Dome Camera·Quick Start Guide Figure 2-6 Tighten the Three Screws 6. Align the bubble to the screw holes on the pedestal and tighten the lock screws on the bubble to finish the installation. Figure 2-7 Installation Finished 2.3 Wall Mounting You need to purchase a wall bracket separately if wall mounting is selected. Steps: 1. Unscrew the three screws on the camera housing and remove the bubble and the black liner.
Network Dome Camera·Quick Start Guide 2. Align the three screws holes on the camera pedestal to the screws holes on the bowl-shaped cap. 3. Route the network cable and power supply cable through the bowl-shaped cap and fix the camera on the cap. IN DC12V Bowl-Shaped Cap Figure 2-8 Fix the Camera 4. Align the bowl-shaped cap to the wall bracket top and rotate the bowl-shaped cap clockwise to fix the cap on the wall bracket.
Network Dome Camera·Quick Start Guide 5. Fix the supplied expansion bolts on the wall. Wall Expansion Bolts Figure 2-10 Fix the Expansion Bolts 6. Align the screw holes on the wall bracket pedestal to the expansion bolts and fix the wall bracket to the expansion bolts with bolts. Wall INDC12V Wall Bracket Pedestal Figure 2-11 Install the Wall Bracket 7. Adjust the monitoring angle. See step 4 of section 2.2 for details..
Network Dome Camera·Quick Start Guide 8. Replace the black liner and bubble on the camera. 9. Fix the lock screw on the wall bracket top and bowl-shaped cap to finish the installation. IN DC12V Lock Screw Figure 2-12 Install the Black Liner and Bubble 2.4 Installing the Camera with Junction Box 1. Drill the screw holes in the wall according to the supplied drill template.
Network Dome Camera·Quick Start Guide 2. Unscrew the 4 screws on the cover of the junction box and remove the cover to open the junction box. Figure 2-14 Open the Junction Box 3. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws. Figure 2-15 Fix the Junction Box 4. Route the camera cables from the hole that marked CAMERA on the junction box and tighten the waterproof nut on the cables.
Network Dome Camera·Quick Start Guide IN DC12 V Waterproof Nut Figure 2-16 Route the Cables 5. Route the network cables from the two other holes of the junction box and connect the corresponding cables in the junction box. IN DC12V Figure 2-17 Connect the Cables 6. Tighten the waterproof nuts after cable connection. Close and fix the cover of junction box with screws.
Network Dome Camera·Quick Start Guide Figure 2-18 Fix the Cover of Junction Box 22
Network Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
Network Dome Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Dome Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Dome Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch.
Network Dome Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Dome Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Dome Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Dome Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Dome Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Dome Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Dome Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Dome Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Dome Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Dome Camera·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0
