How to Guide

ManualsBrandsHIKVISION ManualsBuilding Technology & Smart LivingHIKVISION DS-2TD2636B-15/P LAN IP IR CCTV camera with temperature monitor 2688 x 1520 p

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: +86-571-8807-5998 • Fax: +1 909-595-0788

E-Mail: support@hikvision.com • www.hikvision.com

How to Configure Temperature Screening

Thermographic Camera with Blackbody

1. General Parameters

 Temperature Measurement Range

30.0-45.0 Degrees Celsius

 Temperature Measurement Accuracy

± 0.3 Degrees Celsius

 Camera Resolution and Focal Length

DS-2TD1217B-3/PA: Thermal: 160 × 120, Optical: 2688 × 1520, 3mm

DS-2TD1217B-6/PA: Thermal: 160 × 120, Optical: 2688 × 1520, 6mm

DS-2TD2617B-6/PA: Thermal: 160 × 120, Optical: 2688 × 1520, 6mm

DS-2TD2637B-10/P: Thermal: 384 × 288, Optical: 2688 × 1520, 10mm

DS-2TD2636B-15/P: Thermal: 384 × 288, Optical: 2688 × 1520, 15mm

 AI Face Detection

Multiple targets skin-surface temperature detection at the same time (wearing

masks or not would not affect this detection)

 Operating Environment

Indoor environment with calm air condition; 10-35 Degrees Celsius

2. Installation

1) Installation Cautions

The performance of this Temperature-screening scheme is greatly affected by

environment. This scheme would apply only to those indoor environments, or the

scenarios with calm air and consistent temperature. Besides, the relative installation

location of devices and the ambient light (too bright or too dark) greatly affect the

accuracy of face detection. In order to improve measurement accuracy and reach

better performance of human face detection, the installation environment has to

meet certain requirements:

1. Select installation environments with one-direction path to ensure that cameras

capture the full faces of all passing persons.

2. Select installation environments with stable and sufficient lighting conditions.

Supplementary light is required under backlight or insufficient lighting conditions

Summary of content (11 pages)

PAGE 1
How to Configure Temperature Screening Thermographic Camera with Blackbody 1. General Parameters  Temperature Measurement Range 30.0-45.0 Degrees Celsius  Temperature Measurement Accuracy ± 0.
PAGE 2
3. 4. 5. 6. 7. to ensure the clear visibility of facial features. Select indoor environments with calm air and consistent temperature condition. Outdoor environments with rapid temperature changes are not recommended. If this scheme is used in entrance scenes that connect indoors and outdoors environments, It is suggested that the installation location should be kept at a certain distance from the entrance (such as customs or security checkpoints).
PAGE 3
) Blackbody Installation Installation location: The recommended distance between the camera and the blackbody is in the above table. The blackbody is recommend to be installed at a height of 1.7m, with an elevation angle of within 15°. Ensure that the black body appears in the upper left / upper right corner of the camera view. Make sure that the blackbody would not be blocked by any other target during temperature measurement. Configuration Steps: 1. Device start-up; 2.
PAGE 4
3. Configuration 1) Select VCA Resource Type Steps: 1. Enter VCA Resource Type interface: Configuration > System > Maintenance > VCA Resource Type. 2. Select Temperature Screening as VCA Resource Type. 3. Click Save and wait for device restart. © Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: +86-571-8807-5998 • Fax: +1 909-595-0788 E-Mail: support@hikvision.com • www.hikvision.
PAGE 5
2) Set Local Configuration Steps: 1. Go to the Local Configuration interface: Configuration > Local. 2. Click to enable the following settings:  Rules: It refers to the rules on your local browser; select Enable to display bounding boxes and temperature information when the face target is detected.  Display Rules Info. on Capture: Select Yes Display rules information on the capture.  Display Temperature Info.: Select Yes to display temperature information with temperature measurement rule configured.
PAGE 6
3) Settings of Temperature Screening Steps: 1. Go to the Temperature Screening Settings interface: Temperature Screening > Basic Settings. 2. Configure the following settings:  Enable Temperature Measurement: Check this box to enable temperature measurement.  Display Temperature Info. on Stream: Check this box to display temperature information on stream.  Emissivity: The relative ability of material surface to emit energy by radiation. For human skin, this value is normally set as 0.98.
PAGE 7
4. Go to the Temperature Screening Settings interface: Temperature Screening > Temperature Screening Configuration 5. Select the optical camera channel (normally as Camera 01). 6.         7. 8. Configure the following settings: Enable Face Detection: Check this box to enable face detection function. Display Temperature: Check this box to display measured temperature. Upload Captured Face Image: Check this box to upload captured face image.
PAGE 8
9. Configure the following settings:  Black Body Parameters: If a blackbody is used for best performance of real-time body temperature measurement correction, the following settings should be configured.  Enable Blackbody Correction: Check this box if a blackbody is used for temperature correction.  Distance: The actual distance between the camera and the blackbody.  Set Temperature and Emissivity with the actual parameters of the used blackbody.
PAGE 9
4) Manual Calibration Purpose: The performance of this body thermography scheme offered by HIKVISION would be affected by different actual working environments, and the affect factors in most stable environments could be regarded as a kind of system error. If needed, it is suggested to make a compensation through the manual calibration, the steps are as following. Steps: 1. Device start-up; wait a period of time (more than 60 minutes) for preheating. 2.
PAGE 10
temperature check. © Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: +86-571-8807-5998 • Fax: +1 909-595-0788 E-Mail: support@hikvision.com • www.hikvision.
PAGE 11
First Choice for Security Professionals HIKVISION Technical Support © Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: +86-571-8807-5998 • Fax: +1 909-595-0788 E-Mail: support@hikvision.com • www.hikvision.