Thermal & Optical Bi-spectrum Network Bullet Camera Quick Start Guide i
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Symbol Convention The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera ● Use of the product must be in strict compliance with the local electrical safety regulations. Storage ● Store the device in dry, well-ventilated, corrosive-gas-free, no direct sunlight, and no heating source environment. Neglect may cause fire hazard. ● To avoid heat accumulation, good ventilation is required for a proper operating environment. ● DO NOT touch the heat dissipation component to avoid burns.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera ● Make sure that the power has been disconnected before you wire, install, or disassemble the device. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC, 24 VAC , or PoE (802.3af) according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Use the power adapter provided by qualified manufacturer.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera however, our company will provide timely technical support if required. ● Please enforce the protection for the personal information and the data security as the device may be confronted with the network security problems when it is connected to the Internet. Please contact us when the device might exist network security risks.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera ● Keep the camera away from liquid while in use. Emergency ● If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. User Manual of Device Scan the QR code to view the latest user manual of device on your mobile phone. Note that mobile data charges may apply if Wi-Fi is unavailable.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Table of Contents 1 Appearance Description ................................................................. 3 1.1 Type I Camera Appearance .............................................. 3 1.2 Type II Camera Appearance ............................................. 5 1.3 Type III Camera Appearance ............................................ 5 1.4 Type IV Camera Appearance ........................................... 6 1.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 4 Access via Web Browser ............................................................... 36 Appendix ......................................................................................... 39 Common Material Emissivity Reference ..............................
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 1 Appearance Description There are four thermal & optical bi-spectrum network bullet cameras. Here are the overviews of Type I camera, Type II camera, Type III camera, and Type IV camera. 1.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Wall Mounting Bracket (Optional) Description No. Description No.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 1.2 Type II Camera Appearance Mount Sun Shield Thermal Lens Memory Card Optical Lens Type II Camera Appearance 1.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Sun Shield Camera Memory Card Slot Bracket Holder Cable Outlet Bracket Hinge Bracket Arm Junction Box Cover Reset Button Junction Box Base Sealing Interface Type III Camera Cables 1.4 Type IV Camera Appearance Bracket Sun Shield Reset Button Memory Card Slot Speaker Thermal Lens White Light Lamp Optical Lens Type IV Camera Appearance 1.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera provided for certain camera models. Refer to the actual device.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Name Description are connected correctly. Network Interface Alarm Interface Connect to the LAN interface. PoE (802.3af) is supported. Two-way alarm input and alarm output are supported. Alarm In: IN1, G/IN2, and G Alarm Out: 1A, 1B/2A, and 2B Audio Interface RS-485 Interface ● ● ● Audio In: Pickup Audio Out: Loudspeaker Control line. The cables may vary according to different models.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera interfaces of the junction box. You can refer to the figure below for connection. The junction box is different according to different models.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC, 24 VAC, or PoE (802.3af). Please make sure your power supply matches with your camera. ● Make sure all the related devices are powered off during the installation. ● Check the specification of the products for the installation environment.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2.1 Install Memory Card 2.1.1 Insall Type I Camera Memory Card Steps: 1. Unscrew and remove the sun shield.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2. Unscrew and remove the back cover. Back Cover Screws Remove Back Cover Case 3. Insert a micro SD card into the micro SD card slot. microSD Card Slot microSD Card Insert micro SD Card 4. Fix the sun shield and back cover to the camera body with the removed screws.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Fix Sun Shield and Back Cover 2.1.2 Install Type II and Type IV Camera Memory Card The memory cards of Type II and Type IV camera are installed in the same way. Here is an example of memory card installation for type II camera. Steps: 1. Unscrew and remove the memory card slot cover. Remove Card Slot Cover 2. Insert a micro SD card into the micro SD card slot until the card clicks.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Insert micro SD Card 3. Cover the memory card slot and fix the screws on the memory card slot cover. 2.1.3 Install Type III Camera Memory Card Steps: 1. Unscrew the memory card slot cover and remove it. SD CARD Memory Card Cover Remove Card Slot Cover 2. Insert the memory card into the memory card slot.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Memory Card Insert Memory Card 3. Cover the memory card slot and fix the screws on the memory card slot cover. 2.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Identification 35 m range (Vehicles) 70 m 79 m 113 m 169 m 282 m 395 m Identification 11 m range (Humans) 23 m 26 m 37 m 55 m 92 m 129 m Take human as 0.5 m (width) × 1.8 m (height), and limit length is 0.75 m. The vehicle limit length is 2.3 m. Detect target: The target should be at least 1.5 pixels on the image. Recognize target: The target should be at least 6 pixels on the image.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2.3 Install Camera 2.3.1 Install Type I Camera Steps: 1. Fix the bullet camera with the mounting bracket with expansion screws or bolts, as shown in Figure 2-9. Bolts Install the Bracket onto the Wall 2. Fix the bullet camera to the mounting bracket with the supplied screws, as shown in Figure 2-10.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 3. Bolt the camera body to the bracket. Fix the Camera to the Wall 4. Adjust the camera to the optimal surveillance angle. 1) Loosen the pan adjusting screw to adjust panning position [0° to 360°]. Tighten the screw.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2) Loosen the tile adjusting screw to adjust the tilting position [-45° to 45°]. Tighten the screw. Tilting Position [-45° to 45°] Tilt Adjustment Please loosen the screws slightly until you can adjust the camera. DO NOT remove the screws from the bracket. 2.3.2 Install Type II and Type IV Camera Type II and Type IV cameras are installed in the same way. Here is an example of installation for type II camera. Steps: 1.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Drill Template 2. (Optional) For cement walls, drill four Φ5 installation holes according to the template (recommended depth: 25 mm) and insert the expansion screws. Otherwise, skip the step. 3. Drill a cable hole in the center. 4. Install the bullet camera with the screws (supplied). Wall Mounting Ceiling Mounting Wall/Ceiling Mounting 5. Adjust the camera to the optimal surveillance angle.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Bracket type I: 1) Loosen the tilt adjusting screw to adjust tilting position [0° to 360°]. Tighten the screw. 2) Loosen the pan adjusting screw to adjust the panning position [-45° to 45°]. Tighten the screw. 3) Loosen the rotation adjusting screw to rotate the camera [0° to 360°]. Tighten the screw.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Screw 0°-360° 0°-90° 2-Axis Adjustment 2.3.3 Install Type III Camera Before you start: There are three methods of Type III camera installation: wall mounting, ceiling mounting, and stand mounting. Wall Mounting Ceiling Mounting Stand Mounting Type III Camera Installation Methods Steps: 1. Loosen the screws on the junction box cover. 2.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Latch Holes Latches Take Apart Junction Box 3. Attach the drill template (supplied) to the place where you want to fix the camera, and then drill four screw holes (recommended depth: 40mm) in the ceiling/wall according to the drill template. 4. Drill a cable hole according to the A mark of the drill template. Ф10 mm (0.39'') Ф24 mm (0.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 5. Align the hole of drill template with the screw hole of the junction box base to place the junction box onto the wall. 6. Route the screw through the sealing ring, and fix the junction box base on the wall with the screws. Sealing Ring Screw Install Junction Box Base 7. Route the cables through the cable hole. 8. Insert the latches into the latch holes to fix the bracket and camera with the junction box.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 10. Connect the corresponding cables to power on the camera and get the live view. 11. Adjust the camera according to the figure below. 1) Loosen the rotation adjusting screw to rotate the camera [-180° to 180°]. Tighten the screw. Rotation Adjusting Screw Rotation Range [-180°to +180°] R-Axis Adjustment 2) Loosen the tilt adjusting screw to adjust tilting position [-90° to 55°]. Tighten the screw.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 3) Loosen the pan adjusting screw to adjust the panning position [-90° to 90°]. Tighten the screw.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Waterproof Measures (Optional) Purpose: If the camera is installed outdoor, you should use the waterproof accessory or tapes to waterproof the cables. Otherwise the cables might get wet or a short circuit might occur. 2.4.1 Install Network Cable Waterproof Jacket ② ① ③ ④ ⑤ ⑥ Align ③ ④ ⑥ ① Figure 2-26 Install Waterproof Jacket Steps: 1. Feed the network cable through ① and ③ in order. 2.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 2.4.2 Waterproof Other Cables After routing and connecting the cables, use the waterproof tapes to wrap up the cables. Connected cables and spare cables both should be wrapped up as the figures below.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 3 Set the Network Camera over the LAN You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Activation Interface(Web) 4. Create a password and input the password into the password field. We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera For detailed instructions of further configuration, please refer to the user manual of network camera.
Quick Start Guide of Thermal & Optical Bi-spectrum Network Bullet Camera Appendix Common Material Emissivity Reference Material Emissivity Human Skin 0.98 PCB 0.91 Cement Concrete 0.95 Ceramics 0.92 Rubber 0.95 Paint 0.93 Wood 0.85 Asphalt 0.96 Brick 0.95 Sand 0.90 Soil 0.92 Cotton 0.98 Cardboard 0.90 White Paper 0.90 Water 0.
UD16773B-A 0
