Thermal Bi-spectrum Network Speed Dome Quick Start Guide
Thermal Network Speed Dome Quick Start Guide ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Thermal Network Speed Dome Quick Start Guide EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Thermal Network Speed Dome Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Thermal Network Speed Dome Quick Start Guide or generates direct current. ● Ensure correct wiring of the terminals for connection to an AC mains supply. Battery ● Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Il y a risque d'explosion si la batterie est remplacée par une batterie de type incorrect. Mettre au rebut les batteries usagées conformément aux instructions. ● The built-in battery cannot be dismantled.
Thermal Network Speed Dome Quick Start Guide ● A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details. ● Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary. ● If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired.
Thermal Network Speed Dome Quick Start Guide Table of Contents 1 Preparation .................................................................................................. 1 2 Appearance Description ............................................................................... 2 2.1 Speed dome Appearance ......................................................................................... 2 2.2 Cable Descriptions .....................................................................................
Thermal Network Speed Dome Quick Start Guide 1 Preparation Basic Requirement All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Use the system according to the working environment requirement.
Thermal Network Speed Dome Quick Start Guide 2 Appearance Description There are three kinds of thermal network speed domes: Type I speed dome, Type II speed dome, and Type III speed dome. The appearance description of three cameras are shown below. 2.1 Speed dome Appearance Refer to the following figures for thermal speed domes overview. Type I Speed Dome Type II Speed Dome Type III Speed Dome Figure 2-1 Thermal Speed dome Overview 2.
Thermal Network Speed Dome Quick Start Guide Power Cable EEN GR D RE OW/ LL YE ACK BL RS485RS485+ 24V AC 24V AC 85 R4 + 85 R4 OW LL YE GE AN OR VIDEO Video Cable Audio Input / Output Alarm Outputs Alarm Inputs Network Cable Figure 2-2 Cables of Thermal Speed domes 2.3 Alarm In/Out Connections This section is only for the speed dome with alarm in/out functions. The speed dome can be connected with alarm inputs (0~5VDC) and alarm outputs.
Thermal Network Speed Dome Quick Start Guide 3 Installing the Speed dome Before you start: 1. Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. 2. Please turn off the power of the speed dome before connecting the cables. Do not drag the speed dome with its waterproof cables, or the waterproof performance is affected. Please remove the protective film on the dome after the installation.
Thermal Network Speed Dome Quick Start Guide 3.1 Monitoring Distance Range Electric lens is adopted for the thermal channel of speed dome. It supports auto-focus function and remote focus function. For different lens focal length, the monitoring range is shown in the table below: Table 3-1 Monitoring Range (Pixel Interval: 17um) Lens Focal Length/mm 10 25 50 75 100 MRAD 1.70 0.68 0.34 0.23 0.
Thermal Network Speed Dome Quick Start Guide This table is for reference only, and the actual detection range may vary according to different camera settings, mounting condition, monitor and so on. When the weather is fine and the atmospheric visibility is normal, the probability of detecting/recognizing/identifying target is 50%. The human width is presumed as 0.5m (human width cannot exceed 0.75m), the human height is presumed as 1.8m, and the vehicle width cannot exceed 2.3m. 3.
Thermal Network Speed Dome Quick Start Guide Waterproof Measures (Optional) Purpose: If the camera is installed outdoor, you should use the waterproof accessory or tapes to waterproof the cables. Otherwise the cables might get wet or a short circuit might occur. Install Network Cable Waterproof Jacket ② ① ④ ③ ⑤ ⑥ Align ③ ④ ⑥ ① Figure 1-3 Install Waterproof Jacket Steps: 1.Feed the network cable through ① and ③ in order. 2.Fix ② on the network cable between ① and ③. 3.
Thermal Network Speed Dome Quick Start Guide 3.3 Installing Memory Card Steps: 1. Remove the protective sticker as shown in Figure 3-2. Protective Sticker Figure 3-2 Remove Protective Sticker 2. Remove the cover on the back of the speed dome. Insert the SD card to the SD card slot and install the cover back. SD Card Slot Figure 3-3 SD Card Slot 3.4 Installing Speed Dome 1. Install the bracket. 1). Take out the bracket and all accessories.
Thermal Network Speed Dome Quick Start Guide Figure 3-4 Bracket and Accessories 2). Drill four Φ12 expansion screw holed on the wall and insert the delivered screws into the holes. Figure 3-5 Drill Screw Holes 3). Secure the wall mounting bracket with 4 hex nuts and washers. Figure 3-6 Secure the Bracket 2. Stick thread tape to the thread of the head cover and rotate the head cover. Secure the head cover to the bracket with delivered set screws. Head Cover ③ ① ② Figure 3-7 Secure the Head Cover 3.
Thermal Network Speed Dome Quick Start Guide + Figure 3-8 Buckle the Handle 2). Hook the two ends of the safety rope to the back box of the speed dome and the bracket respectively. 3). Hitch the speed dome onto the head cover with the hook on the back box. Hook Back Box Figure 3-9 Hang the Speed Dome 4). Route the cables through the head cover and bracket.
Thermal Network Speed Dome Quick Start Guide Figure 3-10 Route the Cables 4. Install the dome body to the head cover for camera type III 1). Hook the two ends of the safety rope to the back box of the speed dome and the bracket respectively. Safety Rope Figure 3-11 Hang the Speed Dome 2). Route the cables through the head cover and bracket.
Thermal Network Speed Dome Quick Start Guide Cables Figure 3-12 Route the Cables 5. Connect the corresponding cables. 6. Align the back box of the speed dome with the head cover. Use an L-wrench to tighten the lock screws to secure the speed dome and the bracket.
Thermal Network Speed Dome Quick Start Guide dome, and a pendent adapter is required if any other bracket is selected. 1 The dimension of pendant adapter is G12 . Pendant Adapter Lock Screw Figure 3-14 Pendent Adapter 3.5 Finishing Installing Connect the corresponding cables and turn the power on; the system will do the self-test automatically. Make sure the live view image and the PTZ control work normally and then finish the installation.
Thermal Network Speed Dome Quick Start Guide 4 Setting the System over the LAN You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.
Thermal Network Speed Dome Quick Start Guide 2. Power on the system, and connect the system to the network. 3. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. The default IP address of the system is 192.168.1.64. Figure 4-2 Activation Interface(Web) 4. Create a password and input the password into the password field.
Thermal Network Speed Dome Quick Start Guide Select inactive device. Input and confirm password. Figure 4-3 SADP Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Thermal Network Speed Dome Quick Start Guide 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 4-4 Modify the IP Address 4. Input the password and click Save to activate your IP address modification.
Thermal Network Speed Dome Quick Start Guide 5 Operating via Web browser 5.1 Accessing the System System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome8 and above version Steps: 1.
Thermal Network Speed Dome Quick Start Guide 5. Install the plug-in before viewing the live video and managing the network speed dome. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. Figure 5-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login.
Thermal Network Speed Dome Quick Start Guide Menu Bar PTZ Control Show or hide PTZ control panel Live View Window Live View Parameters Toolbar Preset/ Patrol/ Pattern Figure 5-3 Live View Page Menu Bar: Click each tab to enter Live View, Playback, Picture, and Configuration page respectively. Click to display the help file of the speed dome. Click to logout the system. Live View Window: Display the live video. Toolbar: Operations on the live view page, e.g.
Thermal Network Speed Dome Quick Start Guide 6 Appendix 6.1 Common Material Emissivity Reference Material Emissivity Human Skin 0.98 PCB 0.91 Cement Concrete 0.95 Ceramics 0.92 Rubber 0.95 Paint 0.93 Wood 0.85 Asphalt 0.96 Brick 0.95 Sand 0.90 Soil 0.92 Cotton 0.98 Cardboard 0.90 White Paper 0.90 Water 0.
Thermal Network Speed Dome Quick Start Guide 6.2 Frequently Asked Questions (FAQ) 6.2.1 Device Running Error Question: The device fails to start up or reboots repeatedly. The device constantly powers off unexpectedly when you pan/tilt the device or call preset. The device fails to zoom in/out or pan/tilt. Answer: Examine the power supply of the speed dome and see whether it meets the requirements. Select the power supply as close as possible.
Thermal Network Speed Dome Quick Start Guide Examine if the IE plug-in is well installed. Change the Website Blocker settings if necessary. For cross-domain routing, enable the UPnP of device, or set manual mapping to port No. 80, 8000, or 554. Examine if the live view channel amount exceeds the upper limit. Examine the network bandwidth. Question: Focus fails when you test outdoor device in indoor situation. Answer: Restore the device to default settings. Adjust the Min.
UD22510B
