User's Manual
Table Of Contents
- Product Key Features
- Chapter 1 Introduction
- 1.1 Front Panel
- 1.2 IR Remote Control Operations
- 1.3 USB Mouse Operation
- 1.4 Rear Panel
- 1.4.1 DS-7100HQHI-K1, DS-7200HUHI-K (/P), iDS-7200HUHI-K/4S, DS-7200HTHI-K, DS-7200HQHI-K(/P), and iDS-7200HQHI-K/S
- 1.4.2 iDS-7200HQHI-K/S(B) and iDS-7200HQHI-M/S
- 1.4.3 DS-7100HUHI-K1
- 1.4.4 iDS-7200HUHI-K/4S(B) and iDS-7200HUHI-M2/S
- 1.4.5 DS-7200HQHI-K1/E and DS-7200HUHI-K1/E
- 1.4.6 DS-7300HQHI-K
- 1.4.7 DS-7300HUHI/HTHI-K4, iDS-7316HUHI-K4/16S and DS-9000HUHI-K8
- 1.4.8 DS-7300HQHI/HUHI-K4, DS-8100HQHI/HUHI-K8, DS-9000HUHI-K8, and iDS-9016HUHI-K8/16S
- 1.4.9 DS-7200HGHI-K1
- 1.4.10 DS-7200HGHI-K2
- 1.4.11 DS-8100HTHI-K8
- 1.4.12 DS-9000HTHI-K8
- Chapter 2 Getting Started
- Chapter 3 Camera Management
- Chapter 4 Camera Settings
- Chapter 5 Live View
- Chapter 6 PTZ Control
- Chapter 7 Storage
- 7.1 Storage Device Management
- 7.2 Storage Mode
- 7.3 Recording Parameters
- 7.4 Configure Recording Schedule
- 7.5 Configure Continuous Recording
- 7.6 Configure Motion Detection Triggered Recording
- 7.7 Configure Event Triggered Recording
- 7.8 Configure Alarm Triggered Recording
- 7.9 Configure Picture Capture
- 7.10 Configure Holiday Recording and Capture
- 7.11 Configure Redundant Recording and Capture
- 7.12 Configure 1080p Lite
- Chapter 8 Disk Array
- Chapter 9 File Management
- Chapter 10 Playback
- Chapter 11 Event and Alarm Settings
- Chapter 12 POS Configuration
- Chapter 13 VCA Event Alarm
- 13.1 Human Body Detection
- 13.2 Face Detection
- 13.3 Vehicle Detection
- 13.4 Line Crossing Detection
- 13.5 Intrusion Detection
- 13.6 Region Entrance Detection
- 13.7 Region Exiting Detection
- 13.8 Unattended Baggage Detection
- 13.9 Object Removal Detection
- 13.10 Audio Exception Detection
- 13.11 Sudden Scene Change Detection
- 13.12 Defocus Detection
- 13.13 PIR Alarm
- Chapter 14 Smart Analysis
- Chapter 15 Human Body Detection
- Chapter 16 Network Settings
- Chapter 17 System Maintenance
- Chapter 18 General System Settings
- Chapter 19 Appendix
Network Video Recorder User Manual
151
Chapter 13 VCA Event Alarm
The device supports receiving the VCA detections sent by connected IP cameras. Enable and
configure the VCA detection on the IP camera settings interface first.
VCA detections must be supported by the connected IP camera.
Refer to the User Manual of Network Camera for the detailed instructions for the VCA
detection.
Human Body Detection
Purpose:
The human body detection is used to detect the human body appearing in the monitoring scene,
and capture the human body pictures.
This feature is available only when the connected camera supports the human body detection.
Go to System > Event > Smart Event.
Click Human Body.
Select the camera to configure the human body detection.
Check Save VCA Picture to save the captured pictures of human body detection.
Check Target of Interest (Human Body) to discard non-human body pictures and videos
which are not triggered by human body detection.
Set detection area.
1) Select the detection area to configure from the Area drop-down list. Up to 8 detection
areas are selectable.
2) Check the checkbox of Enable Area to enable the selected detection area.
3) Edit the area name in the Scene Name. The scene name can contain up to 32 characters.