Network Video Recorder Quick Start Guide
Network Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description .......................................................................................................................... 7 1.1 Front Panel........................................................................................................................................... 7 DS-7600NI-Q1 (/P) and DS-7600-K1(/P) (B) Series.........................................................................
Network Video Recorder Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table.
Network Video Recorder Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Network Video Recorder Quick Start Guide Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit. Use the device in conjunction with an UPS if possible. Power down the unit before connecting and disconnecting accessories and peripherals. A factory recommended HDD should be used for this device.
Network Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel DS-7600NI-Q1 (/P) and DS-7600-K1(/P) (B) Series Figure 1-1 DS-7600NI-Q1 (/P) and DS-7600-K1(/P) (B) Series Table 1-1 Panel Description No. Name 1 2 Status Indicator Description Power Power indicator turns green when system is running. Status Status indicator blinks red when data is being read from or written to HDD. Tx/Rx Tx/Rx indictor blinks green when network connection is functioning properly.
Network Video Recorder Quick Start Guide Table 1-2 Panel Description No. Name Connections 1 POWER Turns green when device is powered up. 2 HDD Flickers red when data is being read from or written to HDD. 3 Tx/Rx Flickers blue when network connection is functioning properly. 4 USB Interface Universal Serial Bus (USB) port for additional devices such as USB mouse and USB Hard Disk Drive (HDD).
Network Video Recorder Quick Start Guide 1.2 Rear Panel DS-7600NI-Q1, DS-7600NI-K1 (B) and DS-7600NI-Q2 Series Figure 1-4 DS-7600NI-Q1, DS-7600NI-K1 (B)and DS-7600NI-Q2 Series Table 1-4 Panel Description No. Item Description 1 Power Supply 12 VDC power supply. 2 Audio In RCA connector for audio input. 3 HDMI Interface HDMI video output connector. 4 LAN Network Interface 1, 10 /100 /1000 Mbps self-adaptive Ethernet interface. 5 Audio Out RCA connector for audio output.
Network Video Recorder Quick Start Guide Figure 1-6 DS-7600NI-Q2/16P Series Table 1-5 Panel Description No. Item Description 1 Power Supply 100~240 VAC power supply. 2 Audio In RCA connector for audio input. 3 HDMI Interface HDMI video output connector. 4 LAN Network Interface 1, 10 /100 /1000 Mbps self-adaptive Ethernet interface 5 Audio Out RCA connector for audio output. 6 VGA Interface DB9 connector for VGA output. Display local video output and menu.
Network Video Recorder Quick Start Guide Figure 1-8 DS-7700NI-Q4/P Series The DS-7716NI-Q4/16P and DS-7732NI-Q4/16P provides 16 network Interfaces with PoE function. Figure 1-9 DS-8600NI-Q8 Series Table 1-6 Panel Description No. Item Description 1 LAN Network Interface 2, 10 /100 /1000 Mbps self-adaptive Ethernet interface 2 Audio Out RCA connector for audio output. 3 HDMI Interface HDMI video output connector.
Network Video Recorder Quick Start Guide 11 ALARM OUT Connector for alarm output. 12 RS-232 Interface Connector for RS-232 devices. 13 Audio In RCA connector for audio input. 14 ALARM OUT Connector for alarm output (optional). 15 eSATA Connects external SATA HDD, CD/DVD-RM. 16 Network Interfaces with PoE function Network interfaces for the cameras and to provide power over Ethernet.
Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 NVR Installation During installation of the NVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the NVR is grounded.
Network Video Recorder Quick Start Guide Figure 2-2 Connect Data Cable Step 3 Connect the power cable to the HDD. Figure 2-3 Connect Power Cable Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
Network Video Recorder Quick Start Guide 2.3 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 96K 42M 128K 56M 160K 70M 192K 84M 224K 98M 256K 112M 320K 140M 384K 168M 448K 196M 512K 225M 640K 281M 768K 337M 896K 393M 1024K 450M 1280K 562M 1536K 675M 1792K 787M 2048K 900M 4096K 1.8G 8192K 3.6G 16384K 7.
Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.
Network Video Recorder Quick Start Guide Step 2 Press the POWER button on the front panel. The Power LED should turn blue. The unit will begin to start. After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording. To shut down the NVR: Step 3 Enter the Shutdown menu. Menu > Shutdown Figure 3-2 Shutdown Step 4 Select the Shutdown button. Step 5 Click the Yes button. 3.
Network Video Recorder Quick Start Guide Figure 3-3 Set Admin Password STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Network Video Recorder Quick Start Guide 3.4 Using the Unlock Pattern for Login For the Admin user, you can configure the unlock pattern for device login. After the device is activated, you can enter the following interface to configure the device unlock pattern. Step 1 Use the mouse to draw a pattern among the 9 dots on the screen. Release the mouse when the pattern is done. Figure 3-5 Draw the Pattern Connect at least 4 dots to draw the pattern. Each dot can be connected for once only.
Network Video Recorder Quick Start Guide If NVR has logged out, you must login the device before operating the menu and other functions. Step 1 Select the User Name in the dropdown list. Figure 3-7 Login Step 2 Input Password. Step 3 Click OK to log in. In the Login dialog box, if you enter the wrong password 7 times, the current user account will be locked for 60 seconds. 3.6 Using the Setup Wizard The Setup Wizard can walk you through some important settings of the device.
Network Video Recorder Quick Start Guide 3.7 Network Settings Purpose: Network settings must be properly configured before you operate NVR over network. Step 1 Enter the Network Settings interface. Menu > Configuration > Network Figure 3-9 Network Settings Step 2 Select the General tab. Step 3 In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server.
Network Video Recorder Quick Start Guide You can select one of the following three options to add the IP camera. OPTION 1: Step 1 Click to select an idle window in the live view mode. Step 2 Click the icon in the center of the window to pop up the Add IP Camera interface. Figure 3-10 Add IP Camera Step 3 Select the detected IP camera and click the Add button to add it directly, and you can click the Search button to refresh the online IP camera manually.
Network Video Recorder Quick Start Guide 3.10 Recording Settings Before you start: Make sure that the disk has already been installed. If not, please install a disk and initialize it. You may refer to the user manual for detailed information. Purpose: Two kinds of record types are introduced in the following section, including Instant Record and All-day Record. And for other record types, you may refer to the user manual for detailed information.
Network Video Recorder Quick Start Guide Figure 3-12 Playback Interface Step 4 Select the channel(s) to or execute simultaneous playback of multiple channels.
Network Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose: You can get access to the device via web browser.
Network Video Recorder Quick Start Guide If the device is already activated, enter the user name and password in the login interface, and click the Login button. Figure 4-2 Login Step 3 Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Video Recorder Quick Start Guide UD12053B-A 27