User Manual of DS-9600/8600/7700/7600 Series NVR User Manual of DS-9600/8600/7700/7600 Series NVR Version 2.3.
User Manual of DS-9600/8600/7700/7600 Series NVR Hikvision® Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision).
User Manual of DS-9600/8600/7700/7600 Series NVR Regulatory information FCC information FCC compliance : This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
User Manual of DS-9600/8600/7700/7600 Series NVR Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • • • • • Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf.
User Manual of DS-9600/8600/7700/7600 Series NVR Product Key Features General Connectable to network cameras, network dome and DVS. Connectable to the third-party network cameras like AXIS, ONVIF, PANASONIC, PSIA, SAMSUNG and SANYO. PAL/NTSC adaptive video inputs. Each channel supports dual-stream. Up to 64 network cameras can be connected for DS-9600/8600 series NVR, 32 network cameras for 7700NI-ST/SP, and 16 network cameras for 7600NI-ST/SP.
User Manual of DS-9600/8600/7700/7600 Series NVR Pre-record and post-record for alarm, motion detection for recording, and pre-record time for schedule and manual recording. Searching record files and captured pictures by events (alarm input/motion detection). Tag adding for record files, searching and playing back by tags. Locking and unlocking record files. Local redundant recording and capture. Provide new playback interface with easy and flexible operation.
User Manual of DS-9600/8600/7700/7600 Series NVR Remote web browser access by HTTPS ensures high security. Remote reverse playback via RTSP. Support accessing by the platform via ONVIF. Remote search, playback, download, locking and unlocking of the record files, and support downloading files broken transfer resume. Remote parameters setup; remote import/export of device parameters. Remote viewing of the device status, system logs and alarm status. Remote keyboard operation.
User Manual of DS-9600/8600/7700/7600 Series NVR TABLE OF CONTENTS Product Key Features .............................................................................................................................. 5 Chapter 1Introduction ................................................................................................................................... 12 1.1 Front Panel ........................................................................................................................
User Manual of DS-9600/8600/7700/7600 Series NVR 5.6 Configuring Holiday Record and Capture ..................................................................................... 76 5.7 Configuring Redundant Recording and Capture ............................................................................ 78 5.8 Configuring HDD Group for Recording and Capture.................................................................... 80 5.9 Files Protection ...................................................
User Manual of DS-9600/8600/7700/7600 Series NVR 9.2.9 Configuring HTTPS Port .......................................................................................... 143 9.2.10 Configuring Email .................................................................................................... 144 9.2.11 Configuring UPnP™ ................................................................................................. 145 9.2.12 Configuring High-speed Download ...................................
User Manual of DS-9600/8600/7700/7600 Series NVR 13.1.5 Viewing Network Information .................................................................................. 193 13.1.6 Viewing HDD Information ....................................................................................... 193 13.2 Searching & Export Log Files ..................................................................................................... 195 13.3 Importing/Exporting Configuration Files ............................
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 1 Introduction 12
User Manual of DS-9600/8600/7700/7600 Series NVR 1.1 Front Panel Figure 1. 1 DS-9600NI-ST/RT Figure 1. 2 DS-9600NI-XT Figure 1. 3 DS-8600NI-ST Table 1. 1 Description of Control Panel Buttons No. Name Function Description ALARM READY 1 Status Indicators Turns red when a sensor alarm is detected. Ready indicator is normally blue, indicating that the device is functioning properly. Turns blue when device is controlled by an IR remote.
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name Function Description MODEM (Not for Reserved for future usage. DS-9600NI-XT) TX/RX Blinks blue when network connection is functioning properly. Guard indicator turns blue when the device is in armed status; at this time, an alarm is enabled when an event is detected. GUARD The indicator turns off when the device is unarmed.
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name Function Description Select all items on the list when used in a list field. In PTZ Control mode, it will turn on/off PTZ light (if F1/ LIGHT applicable). In Playback mode, it is used to switch between play and reverse play. Cycle through tab pages. F2/ AUX In synchronous playback mode, it is used to switch between channels. Press the button will help you return to the Main menu (after successful login).
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name Function Description forward/backward in records files. In PTZ control mode, it can control the movement of the PTZ camera. 10 POWER ON/OFF Power on/off switch. Figure 1. 4 DS-7700NI-ST/SP Table 1. 2 Description of Control Panel Buttons No. Name Function Description POWER Turns green when NVR is powered up. READY The indicator is green when the device is running normally.
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name Function Description In single-frame play mode, pressing the Enter button will play the video by a single frame. In auto sequence view mode, the buttons can be used to pause or resume auto sequence. Switch between the numeric or letter input and functions of the SHIFT composite keys. (Input letter or numbers when the light is out; Realize functions when the light is red.) 1/MENU Enter numeral “1”; Access the main menu interface.
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name Function Description In Live View mode, it can be used to cycle through different channels. In the Playback mode, it can be used to jump 30s forward/backward in video files. In PTZ control mode, it can control the movement of the PTZ camera. 6 POWER ON/OFF 7 USB Interfaces Power on/off switch. Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). Figure 1. 5 DS-7600NI-ST/SP Table 1.
User Manual of DS-9600/8600/7700/7600 Series NVR Enter letters “DEF”; The F2 button is used to change the tab pages. In PTZ control mode, it zooms in the image. Enter numeral “4”; 4/GHI/ESC Enter letters “GHI”; Exit and back to the previous menu. Enter numeral “5”; Enter letters “JKL”; 5/JKL/EDIT Delete characters before cursor; Check the checkbox and select the ON/OFF switch; Start/stop record clipping in playback.
User Manual of DS-9600/8600/7700/7600 Series NVR 1.2 IR Remote Control Operations The NVR may also be controlled with the included IR remote control, shown in Figure 1. 6. Note: Batteries (2×AAA) must be installed before operation. Figure 1. 6 Remote Control The keys on the remote control closely resemble the ones on the front panel. See Table 1.5. Table 1. 4 Description of the Soft Keyboard Icons No. Name Description 1 POWER Power on/off the device. 2 DEV Enables/Disables Remote Control.
User Manual of DS-9600/8600/7700/7600 Series NVR Buttons 13 PTZ Button Same as the PTZ/IRIS- button on front panel. 14 ESC Button Same as the ESC button on front panel. 15 RESERVED Reserved for future usage. 16 F1 Button Same as the F1/LIGHT button on front panel. 17 PTZControl Buttons Buttons to adjust the iris, focus and zoom of a PTZ camera. 18 F2 Button Same as the F2/AUX button on front panel.
User Manual of DS-9600/8600/7700/7600 Series NVR 1.3 USB Mouse Operation A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse: 1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR. 2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible reason may be that the two devices are not compatible, please refer to the recommended the device list from your provider.
User Manual of DS-9600/8600/7700/7600 Series NVR 1.4 Input Method Description Figure 1. 7 Soft Keyboard Description of the buttons on the soft keyboard: Table 1.
User Manual of DS-9600/8600/7700/7600 Series NVR 1.5 Rear Panel Figure 1. 8 DS-9600NI-ST/RT Figure 1. 9 DS-9600NI-XT Figure 1. 10 DS-8600NI-ST Figure 1.
User Manual of DS-9600/8600/7700/7600 Series NVR Table 1. 7 Description of Rear Panel Interfaces No. Item Description 1 VIDEO OUT BNC connector for video output. CVBS AUDIO OUT RCA connector for audio output. This connector is synchronized with 2 CVBS video output. VGA AUDIO OUT RCA connector for audio output. This connector is synchronized with VGA video output. 3 LINE IN BNC connector for audio input. 4 RS-232 Interface Connector for RS-232 devices. 5 VGA DB9 connector for VGA output.
User Manual of DS-9600/8600/7700/7600 Series NVR 4 RS-232 Interface Connector for RS-232 devices. 5 VGA DB9 connector for VGA output. Display local video output and menu. 6 HDMI HDMI video output connector. 7 eSATA (Optional) Connects external SATA HDD, CD/DVD-RM. 8 LAN Interface Connector for LAN (Local Area Network). 9 Termination Switch RS-485 termination switch. Up position shows the RS-485 is not terminated. Down position shows the RS-485 is terminated with 120Ω resistance.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 1. 14 DS-7600NI-SP Table 1. 10 Description of Rear Panel Interfaces No. 1 Item Network Interfaces Description Network interface for the cameras and to provide power over Ethernet. with PoE function 2 VIDEO OUT BNC connector for video output. 3 AUDIO OUT BNC connector for audio output. 4 AUDIO IN 5 RS-232 Interface 6 VGA 7 HDMI 8 LAN Interface RS-485 Interface 9 BNC connector for audio input.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 2 Getting Started 28
User Manual of DS-9600/8600/7700/7600 Series NVR 2.1 Starting Up and Shutting Down the NVR Purpose: Proper startup and shutdown procedures are crucial to expanding the life of the NVR. Before you start: Check that the voltage of the extra power supply is the same with the NVR’s requirement, and the ground connection is working properly. Starting up the NVR: Steps: 1. Check the power supply is plugged into an electrical outlet.
User Manual of DS-9600/8600/7700/7600 Series NVR In the Shutdown menu, you can also reboot the NVR. Steps: 1. Enter the Shutdown menu by clicking Menu > Shutdown. 2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR.
User Manual of DS-9600/8600/7700/7600 Series NVR 2.2 Using the Wizard for basic configuration By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure 2. 2. Figure 2. 2 Start Wizard Interface Operating the Setup Wizard: 1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the Setup Wizard at that moment, click the Cancel button.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 4 Date and Time Settings 6. After the time settings, click Next button which takes you back to the Network Setup Wizard window, as shown in Figure 2. 5.
User Manual of DS-9600/8600/7700/7600 Series NVR DS-7700/7600NI-SP Figure 2. 5 Network Configuration Note: Dual-NIC is only supported in DS-9600NI-ST/RT/XT and DS-8600NI-ST device. And for DS-7700/7600NI-SP series NVR, the internal NIC IPv4 address should be configured for the cameras connecting to the PoE network interface of the NVR. 7. Click Next button after you configured the network parameters, which takes you to the Array Management window (supported by DS-9600NI-RT series only). Figure 2.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 7 HDD Management 9. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD. 10. Click Next button. You enter the Adding IP Camera interface. 11. Click Search to find online IP Camera. Select the IP camera to be added, and click the Add button. Figure 2. 8 Search for IP Cameras 12. Click Next button. Configure the recording for the searched IP Cameras.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 9 Record Settings 13. Click Copy to copy the settings to other channels, as shown in Figure 2. 10. Figure 2. 10 Copy Record Settings 14. Click OK to complete the startup Setup Wizard.
User Manual of DS-9600/8600/7700/7600 Series NVR 2.3 Adding and Connecting the IP Cameras 2.3.1 Adding the online IP Cameras Purpose: The main function of the NVR is to connect the network cameras and record the video got from it. So before you can get a live view or record of the video, you should add the network cameras to the connection list of the device. Before you start: Ensure the network connection is valid and correct.
User Manual of DS-9600/8600/7700/7600 Series NVR 3. To add other IP cameras: 1) On the left side of the interface, you can enter the IP address, protocol, management port, user name, password and other information of the IP camera to be added. 2) Click Add to add the camera. 2.3.2 Editing the connected IP cameras and Configuring Customized Protocols After the adding of the IP cameras, the basic information of the camera lists in the page, you can configure the basic setting of the IP cameras.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 15 Password Configuration of the Camera 3. Click Apply to save the settings and click OK to exit the interface. Explanation of the icons Edit basic parameters of the camera Delete the IP camera Get the live view of the camera Configuring the customized protocols Purpose: To connect the network cameras which are not configured with the standard protocols, you can configure the customized protocols for them. Steps: 1.
User Manual of DS-9600/8600/7700/7600 Series NVR rtsp://192.168.1.55:554/ch1/main/av_stream. Protocol Name: Edit the name for the custom protocol. Enable Substream: If the network camera does not support sub-stream or the sub-stream is not needed, leave the checkbox empty. Type: The network camera adopting custom protocol must support getting stream through standard RTSP. Transfer Protocol: Select the transfer protocol for the custom protocol. Port: Set the port No. for the custom protocol.
User Manual of DS-9600/8600/7700/7600 Series NVR 2.3.3 Editing IP cameras connected to the PoE interfaces (Only for DS-7600/7700NI-SP series NVR) The PoE interfaces enables the NVR system to pass electrical power safely, along with data, on Ethernet cabling to the connected network cameras. The DS-7600/7700NI-SP series NVR provides 8 PoE interfaces which can connect to 8 network cameras directly; and if you disable the PoE interface, you can also connect to the online network cameras.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 20 Edit IP Camera Interface - Plug-and-Play • Manual: You can disable the PoE interface by selecting the manual while the current channel can be used as a normal channel and the parameters can also be edited. Figure 2.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 3 Live View 42
User Manual of DS-9600/8600/7700/7600 Series NVR 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC many times (depending on which menu you’re on) brings you to the Live View mode.
User Manual of DS-9600/8600/7700/7600 Series NVR 3.2 Operations in Live View Mode In live view mode, there are many functions provided. The functions are listed below. • • • Single Screen: showing only one screen on the monitor. Multi-screen: showing multiple screens on the monitor simultaneously. Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on the configuration menu before enabling the auto-switch. Menu>Configuration>Live View>Dwell Time.
User Manual of DS-9600/8600/7700/7600 Series NVR Switch between main Press Main/Aux button. and aux output 3.2.2 Using the Mouse in Live View Table 3. 4 Mouse Operation in Live View Name Description Menu Enter the main menu of the system by right clicking the mouse. Single Screen Switch to the single full screen by choosing channel number from the dropdown list. Multi-screen Adjust the screen layout by choosing from the dropdown list. Previous Screen Switch to the previous screen.
User Manual of DS-9600/8600/7700/7600 Series NVR dropdown list. • Multi-screen: Switch between different display layout options. Layout options can be selected from a dropdown list. • Next Screen: When displaying less than the maximum number of cameras in Live View, clicking this feature will switch to the next set of displays. • Playback: Enter into Playback mode. • PTZ: Enter PTZ Control mode. • Main Monitor: Enter Main operation mode.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 3. 3 Digital Zoom Image Settings icon can be selected to enter the Image Settings menu. Figure 3. 4 Image Settings- Preset You can also choose the Customize mode to set the image parameters like brightness, contrast, saturation and hue. Figure 3. 5 Image Settings- Customize Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 3.3 Adjusting Live View Settings Purpose: Live View settings can be customized according to different needs. You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc. Steps: 1. Enter the Live View Settings interface. Menu> Configuration> Live View Figure 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 1) Select a View mode in . 2) Select the small window, and double-click on the channel number to display the channel on the window. You can click button to start live view for all the channels and click live view. 3) Click the Apply button to save the setting.
User Manual of DS-9600/8600/7700/7600 Series NVR 3.4 Channel-zero Encoding Purpose: Sometimes you need to get a remote view of many channels in real time from web browser or CMS(Client Management System) software, in order to decrease the bandwidth requirement without affecting the image quality, channel-zero encoding is supported as an option for you. Steps: 1. Enter the Live View Settings interface. Menu> Configuration> Live View 2. Select the Channel-Zero Encoding tab. Figure 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 3.5 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter user name and password tog in again. Steps: 1. Enter the Shutdown menu. Menu>Shutdown Figure 3. 10 Shutdown 2. Click Logout. Note: After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 4 PTZ Controls 53
User Manual of DS-9600/8600/7700/7600 Series NVR 4.1 Configuring PTZ Settings Purpose: Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you control the PTZ camera. Before you start: Check that the PTZ and the NVR are connected properly through RS-485 interface. Steps: 1. Enter the PTZ Settings interface. Menu >Camera> PTZ Figure 4. 1 PTZ- General 2. Choose the camera for PTZ setting in the Camera dropdown list. 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 4.2 Setting PTZ Presets, Patrols & Patterns Before you start: Please make sure that the presets, patrols and patterns should be supported by PTZ protocols. 4.2.1 Customizing Presets Purpose: Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place. Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings Figure 4. 2 PTZ- More Settings 2.
User Manual of DS-9600/8600/7700/7600 Series NVR 4.2.2 Calling Presets Purpose: This feature enables the camera to point to a specified position such as a window when an event takes place. Call preset in the PTZ setting interface: Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Check the round icon of Call Preset. Figure 4. 4 PTZ- Call Preset 3. Choose the preset number. Call preset in live view mode: Steps: 1.
User Manual of DS-9600/8600/7700/7600 Series NVR 2. Choose Camera in the list on the menu. 3. Double click the preset in the Preset list to call it. 4.2.3 Customizing Patrols Purpose: Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps above in Customizing Presets. Steps: 1. Enter the PTZ Control interface.
User Manual of DS-9600/8600/7700/7600 Series NVR You can also delete all the key points by clicking the trash icon Select a key point, then click or . button to adjust the order of the key points. Figure 4. 8 KeyPoints Deletion 4.2.4 Calling Patrols Purpose: Calling a patrol makes the PTZ to move according the predefined patrol path. Calling patrol in the PTZ setting interface: Steps: 1. In the PTZ setting interface. Menu> Camera> PTZ> More Settings 2. Select the patrol number, and then click 3.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 4. 9 Calling Patrol Calling patrol in live view mode: Steps: 1. Press PTZ control on the front panel or on the remote, or click PTZ Control icon on the quick setting panel, to show the PTZ control panel. 2. Choose Patrol on the control bar. 3. Double click the patrol or select the patrol and click to call it. Figure 4. 10 PTZ Panel- Patrol 4.2.5 Customizing Patterns Purpose: Patterns can be set by recording the movement of the PTZ.
User Manual of DS-9600/8600/7700/7600 Series NVR Menu>Camera>PTZ>More Settings 2. Choose pattern number in the option box. Figure 4. 11 PTZ- Pattern 3. Click and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera. The movement of the PTZ is recorded as the pattern. 4. Click to save the pattern. 4.2.6 Calling Patterns Purpose: Follow the procedure to move the PTZ camera according to the predefined patterns.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 4. 12 PTZ- Calling Pattern Call pattern in live view mode. Steps: 1. In the live view mode, press PTZ control on the front panel or on the remote control, or click PTZ Control icon on the quick setting panel. 2. And then choose Pattern on the control bar. 3. Double click the pattern or select the pattern and click to call it. Figure 4.
User Manual of DS-9600/8600/7700/7600 Series NVR 4.3 PTZ Control Panel In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or choose the PTZ Control icon to enter the PTZ panel. Figure 4. 14 PTZ Panel Table 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 5 Record and Capture Settings 63
User Manual of DS-9600/8600/7700/7600 Series NVR 5.1 Configuring Encoding Parameters Purpose: By configuring the encoding parameters you can define the parameters which affect the image quality, such as the transmission stream type, the resolution and so on. Before you start: 1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu>HDD>General) Figure 5. 1 HDD- General 2.
User Manual of DS-9600/8600/7700/7600 Series NVR 1) Select Record tab page to configure. You can configure the stream type, the resolution, and other parameters on your demand. • Pre-record: The time you set to record before the scheduled time or event. For example, when an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records it at 9:59:55. • Post-record: The time you set to record after the event or the scheduled time.
User Manual of DS-9600/8600/7700/7600 Series NVR 2) Configure the parameters. 3) Click Apply to save the settings. Note: The interval is the time period between two capturing actions. You can configure all the parameters on this menu on your demand.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.2 Configuring Record/Capture Schedule Purpose: Set the record schedule, and then the camera automatically starts/stops recording according to the configured schedule. Note: In this chapter, we take the record schedule procedure as an example, and the same procedure can be applied to configure schedule for both recording and capture. To schedule the automatic capture, you need to choose the Capture tab in the Schedule interface. Steps: 1.
User Manual of DS-9600/8600/7700/7600 Series NVR You can click the button to set the accurate time of the schedule. II. To schedule an all-day recording, check the checkbox after the All Day item. Figure 5. 8 Edit Schedule III. To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 10 Draw the Schedule Descriptions of the color icons are shown in the figure below. Figure 5. 11 Descriptions of the color icons Click the Apply button to validate the settings. If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.3 Configuring Motion Detection Record and Capture Purpose: Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center and so on.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 15 Motion Detection Handling 5) Select the channels which you want the motion detection event to trigger recording. 6) Click Apply to save the settings. 7) Click OK to back to the upper level menu. 8) Exit the Motion Detection menu. 3. Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see Chapter Configuring Record/Capture Schedule.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.4 Configuring Alarm Triggered Record and Capture Purpose: Follow the procedure to configure alarm triggered recording or capture. Steps: 1. Enter the Alarm setting interface. Menu> Configuration> Alarm Figure 5. 16 Alarm Settings 2. Click Alarm Input. Figure 5. 17 Alarm Settings- Alarm Input 1) Select Alarm Input number and configure alarm parameters. 2) Choose N.O (normally open) or N.C (normally closed) for alarm type.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 18 Alarm Handling 5) Choose the alarm triggered recording channel. 6) Check the checkbox to select channel. 7) Click Apply to save settings. 8) Click OK to back to the upper level menu. Repeat the above steps to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number. Figure 5. 19 Copy Alarm Input 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.5 Manual Record and Continuous Capture Purpose: Follow the steps to set parameters for the manual record and continuous capture. Using manual record and continuous capture, you need to manually cancel the record and capture. The manual recording and manual continuous capture is prior to the scheduled recording and capture. Steps: 1. Enter the Manual settings interface. Menu> Manual Or press the REC/SHOT button on the front panel. Figure 5.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.6 Configuring Holiday Record and Capture Purpose: Follow the steps to configure the record or capture schedule on holiday for that year. You may want to have different plan for recording and capture on holiday. Steps: 1. Enter the Record setting interface. Menu>Record> Holiday Figure 5. 22 Holiday Settings 2. Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure 5.
User Manual of DS-9600/8600/7700/7600 Series NVR 3) Select Mode from the dropdown list. There are three different modes for the date format to configure holiday schedule. 3. 4) Set the start and end date. 5) Click Apply to save settings. 6) Click OK to exit the Edit interface. Enter Record/Capture Schedule settings interface to edit the holiday recording schedule. See Chapter 6.2 Configuring Record/Capture Schedule.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.7 Configuring Redundant Recording and Capture Purpose: Enabling redundant recording and capture, which means saving the record files and captured pictures not only in the R/W HDD but also in the redundant HDD, will effectively enhance the data safety and reliability. . Steps: 1. Enter HDD Information interface. Menu> HDD Figure 5. 24 HDD General 2. Select the HDD and click 1) to enter the Local HDD Settings interface. Set the HDD property to Redundancy.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 26 Encoding Record 2) Select Camera you want to configure in the drop-down list. 3) Check the checkbox of Redundant Record/Capture. 4) Click OK to save settings and back to the upper level menu. Repeat the above steps for configuring other channels.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.8 Configuring HDD Group for Recording and Capture Purpose: You can group the HDDs and save the record files and captured pictures in certain HDD group. Steps: 1. Enter HDD setting interface. Menu>HDD Figure 5. 27 HDD General 2. Select Advanced on the left bar. Figure 5. 28 Storage Mode Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information, please refer to Chapter 11.4 Managing HDD Group. 3.
User Manual of DS-9600/8600/7700/7600 Series NVR 4) Click Apply to save settings. Note: After having configured the HDD groups, you can configure the Recording and Capture settings following the procedure provided in Chapter 5.2-5.7.
User Manual of DS-9600/8600/7700/7600 Series NVR 5.9 Files Protection Purpose: You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten. Protect file by locking the record files: Steps: 1. Enter Export setting interface. Menu> Export Figure 5. 30 Export 2. Select the channels you want to investigate by checking the checkbox to 3. Configure the record type, file type start/end time. 4. Click Search to show the results. . Figure 5.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 32 Unlocking Attention Protect file by setting HDD property to Read-only Steps: 1. Enter HDD setting interface. Menu> HDD Figure 5. 33 HDD General 2. Click to edit the HDD you want to protect. Figure 5. 34 HDD General- Editing Note: To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter Managing HDD Group. 3. Set the HDD property to Read-only. 4. Click OK to save settings and back to the upper level menu.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 6 Playback 84
User Manual of DS-9600/8600/7700/7600 Series NVR 6.1 Playing Back Record Files 6.1.1 Playing Back by Channel Purpose: Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. Instant playback by channel Steps: Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar. Note: In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Front Panel: press PLAY button to play back record files of the channel under single-screen live view mode. Under multi-screen live view mode, the recorded files of the top-left channel will be played back. Note: Pressing numerical buttons will switch playback to the corresponding channels during playback process. 2. Playback management. The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in Figure 6. 3.
User Manual of DS-9600/8600/7700/7600 Series NVR Note: Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames. 6.1.2 Playing Back by Time Purpose: Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. Steps: 1. Enter playback interface. Menu>Playback 2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 7 Toolbar of Playback by Time Note: The indicates the start/end time of the record. Table 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 8 Alarm Input Search Interface Figure 6. 9 Motion Search Interface 4. Click Search button to get the search result information. You may refer to the right-side bar for the result.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 10 Search Result Bar(Alarm In and Motion) 5. Click button to play back the file. You can click the Back button to back to the search interface. Note: Pre-play and post-play can be configured. 6. Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 12 Toolbar of Playback by Event Table 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 13 Interface of Playback by Time Click button to add default tag. Click button to add customized tag and input tag name. Note: Max. 64 tags can be added to a single video file. 3. Tag management. Click button to check, edit and delete tag(s). Figure 6. 14 Tag Management Interface Steps: 1. Select the Tag from the drop-down list in the Playback interface. 2.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 15 Video Search by Tag 3. Click button to play back the file. You can click the Back button to back to the search interface. Note: Pre-play and post-play can be configured. Figure 6. 16 Interface of Playback by Tag Figure 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Table 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 19 Result of System Log Search 4. Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6. 20 Interface of Playback by Log 6.1.6 Playing Back External File Purpose: Perform the following steps to look up and play back files in the external devices. Steps: 1. Enter Tag Search interface. Menu>Playback 2. Select the External File in the drop-down list on the top-left side.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6.
User Manual of DS-9600/8600/7700/7600 Series NVR 6.2 Auxiliary Functions of Playback 6.2.1 Playing Back Frame by Frame Purpose: Play video files frame by frame, in case of checking image details of the video when abnormal events happen. Steps: • Using a Mouse: Go to Playback interface. If you choose playback of the record file: click button until the speed changes to Single frame and one click on the playback screen represents playback of one frame.
User Manual of DS-9600/8600/7700/7600 Series NVR 6.2.3 Reverse Playback of Multi-channel Purpose: You can play back record files of multi-channel reversely. Up to 16-ch (with 1280*720 resolution) simultaneous reverse playback is supported; up to 4-ch (with 1920*1080P resolution) simultaneous reverse playback is supported and up to 1-ch (with 2560*1920 resolution) reverse playback is supported. Note: We use the interface of DS-7700NI-ST series (unless stated) as example to describe the following settings.
User Manual of DS-9600/8600/7700/7600 Series NVR 6.3 Picture Playback Purpose: Search and view captured pictures stored in HDD. Steps: 1. Enter Playback interface. Menu>Playback 2. Select the Picture in the drop-down list on the top-left side. Figure 6. 24 Interface of Playback by Picture 3. Choose channels, edit start time and end time, and then click Search to enter Search Result interface. 4. Choose a picture you want to view and click button.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 25 Result of Picture Search 5. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6. 26 Picture Playback Toolbar Table 6.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 7 Backup 101
User Manual of DS-9600/8600/7700/7600 Series NVR 7.1 Backing up Record Files 7.1.1 Quick Export Purpose: Export record files to backup device(s) quickly. Steps: 1. Enter Video Export interface. Menu>Export>Normal Choose the channel(s) you want to back up and click button. Note: The time duration of record files on a specified channel cannot exceed one day. Otherwise, the message box “Max. 24 hours are allowed for quick export.” will pop up. Figure 7. 1 Quick Export Interface 2.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 3 Export Finished 3. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 4 Checkup of Quick Export Result Using USB1-1 7.1.2 Backing up by Normal Video Search Purpose: The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB writer), SATA writer and e-SATA HDD.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 5 Normal Video Search for Backup 3. Select record files you want to back up. Click to play the record file if you want to check it. Check the checkbox before the record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 6 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 7 Export by Normal Video Search using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”. Figure 7. 8 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR Backup using USB writer and SATA writer Steps: 1. Enter Export interface. Menu>Export>Normal 2. Set search condition and click Search button to enter the search result interface. Figure 7. 10 Normal Video Search for Backup 3. Select record files you want to back up. Click button to play the record file if you want to check it. Check the checkbox before the record files you want to back up.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 12 Export by Normal Video Search using USB Writer Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”. Figure 7. 13 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR Backup using eSATA HDDs Steps: 1. Enter Record>Advanced and set the usage of eSATA HDD at “Export”. Menu>Record>Advanced Choose eSATA and set its usage at Export. Click Yes when pop-up message box “System will reboot automatically if the usage of eSATA is changed. Continue?” Note: The usages of eSATA HDD contain Record/Capture and Export. And changes in usage will take effective after rebooting the device. 2. Enter Export interface.
User Manual of DS-9600/8600/7700/7600 Series NVR • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format SATA HDD via the device. Figure 7. 17 Export by Normal Video Search Using eSATA HDD Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 18 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 19 Checkup of Export Result Using eSATA HDD 7.1.3 Backing up by Event Search Purpose: Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or eSATA HDD. Quick Backup and Normal Backup are supported. Steps: 1. Enter Export interface. Menu>Export>Event 1) Select “Alarm Input” from the dropdown list of Event Type. 2) Select the alarm input No. and time.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 21 Result of Event Search 2) Click Details button to view detailed information of the record file, e.g. start time, end time, file size, etc. Figure 7. 22 Event Details Interface 3. Export. Click the Export button and start back up. Note: If the inserted USB device is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 23 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 24 Export Finished 4. Check backup result. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR 7.1.4 Backing up Video Clips Purpose: You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or eSATA HDD. Steps: 1. Enter Playback interface. Please refer to Chapter 6.1 Playing Back Record Files. 2. During playback, use buttons and in the playback toolbar to start or stop clipping record file(s). 3.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 28 Export Video Clips Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 29 Export Finished 6. Check backup result. Note: The Player player.exe will be exported automatically during record file export. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR 7.2 Backing up Pictures Purpose: Back up pictures using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or eSATA HDD. Steps: 1. Enter Export interface. Menu>Export>Picture Select channel(s), image type, start time and end time, and click Search button to enter the Search Result interface. Figure 7. 31 Picture Search for Backup 2. Select pictures you want to back up.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 33 Export Pictures Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 34 Export Finished 4. Check backup result. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR 7.3 Managing Backup Devices Management of USB flash drives, USB HDDs and eSATA HDDs. 1. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. Note: At least one channel shall be selected. Figure 7. 36 Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 38 USB Flash Drive Management Management of USB writers and DVD-R/W 1. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. Note: At least one channel shall be selected. Figure 7. 39 Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface. Note: At least one record file shall be selected.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 40 Result of Normal Video Search for Backup 3. Backup device management. Click Erase button if you want to erase the files from a re-writable CD/DVD. Note: There must be a re-writable CD/DVD when you make this operation. Note: If the inserted USB writer or DVD-R/W is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. Figure 7.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 8 Alarm Settings 120
User Manual of DS-9600/8600/7700/7600 Series NVR 8.1 Setting Motion Detection Alarm Steps: 1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection. Menu> Camera> Motion Figure 8. 1 Motion Detection Setup Interface 2. Set up detection area and sensitivity. Tick “Enable Motion Detection”, use the mouse to draw detection area(s) and drag the sensitivity bar to set sensitivity. Click button and set alarm response actions. 3.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8. 3 Set Arming Schedule of Motion Detection 5. Click Handling tab to set up alarm response actions of motion alarm (please refer to Chapter Setting Alarm Response Actions). 6. If you want to set motion detection for another channel, repeat the above steps or just click Copy in the Motion Detection interface to copy the above settings to it.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.2 Setting Sensor Alarms Purpose: Set the handling method of an external sensor alarm. Steps: 1. Enter Alarm Settings of System Configuration and select an alarm input. Menu> Configuration> Alarm Select Alarm Input tab to enter Alarm Input Settings interface. Figure 8. 4 Alarm Status Interface of System Configuration 2. Set up the handling method of the selected alarm input.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8. 6 Set Arming Schedule of Alarm Input Choose one day of a week and Max. eight time periods can be set within each day, and click Apply to save the settings. Note: Time periods shall not be repeated or overlapped. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5.
User Manual of DS-9600/8600/7700/7600 Series NVR inputs to copy the settings to them. Figure 8.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.3 Detecting Video Loss Alarm Purpose: Detect video loss of a channel and take alarm response action(s). Steps: 1. Enter Video Loss interface of Camera Management and select a channel you want to detect. Menu> Camera> Video Loss Figure 8. 9 Video Loss Setup Interface 2. Set up handling method of video loss. Check the checkbox of “Enable Video Loss Alarm”, and click button to set up handling method of video loss. Figure 8.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8. 11 Set Arming Schedule of Video Loss 4. Select Handling tab to set up alarm response action of video loss (please refer to Chapter Setting Alarm Response Actions). 5. Click the OK button to complete the video loss settings of the channel.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.4 Detecting Video Tampering Alarm Purpose: Trigger alarm when the lens is covered and take alarm response action(s). Steps: 1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video tampering. Menu> Camera> Tamper-proof Figure 8. 12 Tamper-proof Setup Interface 2. Set the video tampering handling method of the channel. Check the checkbox of “Enable Tamper-proof”.
User Manual of DS-9600/8600/7700/7600 Series NVR 3) Click Apply button to save the settings. Note: Time periods shall not be repeated or overlapped. Figure 8. 14 Set Arming Schedule of Video Tampering 4. Select Handling tab to set up alarm response actions of video tampering alarm (please refer to Chapter Setting Alarm Response Actions). 5. Click the OK button to complete the video tampering settings of the channel.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.5 Handling Exceptions Alarm Purpose: Exception settings refer to the handling method of various exceptions, e.g. • • • • • • • HDD Full: The HDD is full. HDD Error: Writing HDD error or unformatted HDD. Network Disconnected: Disconnected network cable. IP Conflicted: Duplicated IP address. Illegal Login: Incorrect user ID or password. Abnormal Record/Capture: No space for saving recorded files or captured images.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.6 Setting Alarm Response Actions Purpose: Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Upload Picture to FTP, Trigger Alarm Output and Send Email.
User Manual of DS-9600/8600/7700/7600 Series NVR 2. Set up arming schedule of the alarm output. Choose one day of a week and up to 8 time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. Figure 8. 17 Set Arming Schedule of Alarm Output 3. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days.
User Manual of DS-9600/8600/7700/7600 Series NVR 8.7 Triggering or Clearing Alarm Output Manually Purpose: Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface. Steps: Select the alarm output you want to trigger or clear and make related operations.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 9 Network Settings 134
User Manual of DS-9600/8600/7700/7600 Series NVR 9.1 Configuring General Settings Purpose: Network settings must be properly configured before you operate NVR over network. Steps: 1. Enter the Network Settings interface. Menu >Configuration>Network 2. Select the General tab. DS-9600NI-ST/RT/XT and DS-8600NI-ST DS-7700/7600NI-ST DS-7700/7600NI-SP Figure 9. 1 Network Settings Interface Note: Dual-NIC configuration is only applicable for DS-9600NI-ST/RT/XT and DS-8600NI-ST series NVR. 3.
User Manual of DS-9600/8600/7700/7600 Series NVR and other network settings from that server. Note: For the 7600/7700NI-SP series NVR, you need to configure the internal NIC address, so that IP addresses are assigned to the cameras connected to the PoE interfaces. Note: The valid value range of MTU is 500 ~ 9676. 4. After having configured the general settings, click to save the settings.
User Manual of DS-9600/8600/7700/7600 Series NVR 9.2 Configuring Advanced Settings 9.2.1 Configuring PPPoE Settings Purpose: Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 9. 3. Figure 9. 3 PPPoE Settings Interface 3. Check the PPPoE checkbox to enable this feature. 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 4 DDNS Settings Interface 3. Check the DDNS checkbox to enable this feature. 4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and EasyDDNS. • IPServer: Enter Server Address for IPServer. Figure 9. 5 IPServer Settings Interface • DynDNS: 1) Enter Server Address for DynDNS (i.e. members.dyndns.org). 2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website.
User Manual of DS-9600/8600/7700/7600 Series NVR 2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP website. Figure 9. 8 NO-IP Settings Interface • hkDDNS: 1) The Server Address of the hkDDNS server appears by default: www.hik-online.com. 2) Enter the Device Domain Name. You can use the alias you registered in the hkDDNS server or define a new device domain name.
User Manual of DS-9600/8600/7700/7600 Series NVR 3) In the Device Management interface, click to register the device. Figure 9. 11 Register the Device Note: The device name can only contain the lower-case English letter, numeric and ‘-’; and it must start with the lower-case English letter and cannot end with ‘-’. 5. Click to save and exit the interface. 9.2.3 Configuring NTP Server Purpose: A Network Time Protocol (NTP) Server can be configured on your NVR to ensure the accuracy of system date/time.
User Manual of DS-9600/8600/7700/7600 Series NVR Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the SNMP tab to enter the SNMP Settings interface, as shown in Figure 9. 13. Figure 9. 13 SNMP Settings Interface 3. Check the SNMP checkbox to enable this feature. 4. Configure the following SNMP settings: • Trap Address: IP Address of SNMP host. • Trap Port: Port of SNMP host. 5. Click to save and exit the interface.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 15 Configure Alarm Host 4. Click to save and exit the interface. 9.2.6 Configuring Multicast Purpose: The multicast can be configured to realize live view for more than 128 cameras through network for DS-9600NI-ST/RT/XT series NVR. And for DS-8600/7700/7600NI-ST NVR, using the multicast function, more than 64 cameras are connectable. A multicast address spans the Class-D IP range of 224.0.0.0 to239.255.255.255.
User Manual of DS-9600/8600/7700/7600 Series NVR 4. Click to save and exit the menu. 9.2.8 Configuring Server and HTTP Ports Purpose: You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and the default HTTP port is 80. Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 14. 3. Enter new Server Port and HTTP Port. Figure 9.
User Manual of DS-9600/8600/7700/7600 Series NVR 9.2.10 Configuring Email Purpose: The system can be configured to send an Email notification to all designated users if an alarm event is detected, etc., an alarm or motion event is detected or the administrator password is changed. Before configuring the Email settings, the NVR must be connected to a local area network (LAN) that maintains an SMTP mail server.
User Manual of DS-9600/8600/7700/7600 Series NVR Enable SSL (optional): Click the checkbox to enable SSL if required by the SMTP server. Sender: The name of sender. Sender’s Address: The Email address of sender. Select Receivers: Select the receiver. Up to 3 receivers can be configured. Receiver: The name of user to be notified. Receiver’s Address: The Email address of user to be notified.
User Manual of DS-9600/8600/7700/7600 Series NVR 3. Check checkbox to enable UPnP™. 4. Select the Mapping Type as Manual or Auto in the drop-down list. Task1: Auto If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router automatically. Steps: 1) Click Apply button to save the settings. 2) You can click Refresh button to get the latest status of the port mapping. Figure 9.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 26 UPnP™ Settings Finished-Manual 9.2.12 Configuring High-speed Download Purpose: You can enable the High-speed Download function to widen the outgoing bandwidth of the device. In this way you can speed up the download of record files through IE browser or CMS software. Note: If you enable the high-speed download function, the local menu operation will be affected.
User Manual of DS-9600/8600/7700/7600 Series NVR 9.3 Checking Network Traffic Purpose: You can check the network traffic to obtain real-time information of NVR such as linking status, MTU, sending/receiving rate, etc. Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect Figure 9. 29 Network Traffic Interface 2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed every 1 second.
User Manual of DS-9600/8600/7700/7600 Series NVR 9.4 Configuring Network Detection Purpose: You can obtain network connecting status of NVR through the network detection function, including network delay, packet loss, etc. 9.4.1 Testing Network Delay and Packet Loss Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect 2. Click the Network Detection tab to enter the Network Detection menu, as shown in Figure 9. 30. Figure 9. 30 Network Detection Interface 3.
User Manual of DS-9600/8600/7700/7600 Series NVR detect the backup device, please check whether it is compatible with the NVR. You can format the backup device if the format is incorrect. Figure 9. 32 Export Network Packet 4. Click to start exporting. 5. After the exporting is complete, click OK to finish the packet export, as shown in Figure 9. 33. Figure 9. 33 Packet Export Attention Note: Up to 1M data can be exported each time. 9.4.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 34 Network status checking If the network is normal the following message box pops out. Figure 9. 35 Network status checking result If the message box pops out with other information instead of this one, you can click show the quick setting interface of the network parameters. Figure 9.
User Manual of DS-9600/8600/7700/7600 Series NVR Note: Dual-NIC configuration is only applicable for the DS-9600NI-ST/RT/XT and DS-8600NI-ST series NVR. 9.4.4 Checking Network Statistics Purpose: You can check the network status to obtain the real-time information of NVR. Steps: 1. Enter the Network Detection interface. Menu>Maintenance>Net Detect 2. Choose the Network Stat. tab. Figure 9. 37 Network Stat. Interface 3.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 10 RAID 153
User Manual of DS-9600/8600/7700/7600 Series NVR Notes: This chapter is applicable for DS-9600NI-RT series only. 10.1 Configuring Array and Virtual Disk Purpose: RAID (redundant array of independent disks) is a storage technology that combines multiple disk drive components into a logical unit. A RAID setup stores data over multiple hard disk drives to provide enough redundancy so that data can be recovered if one disk fails.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.1.1 One-touch Configuration Purpose: Through one-touch configuration, you can quickly create the disk array and virtual disk. By default, the array type to be created is RAID 5. Steps: 1. Enter the Physical Disk Settings interface. Menu > HDD > RAID > Physical Disk Figure 10. 2 Physical Disk Settings Interface 2. Click to enter the One-touch Array Configuration interface.
User Manual of DS-9600/8600/7700/7600 Series NVR and two virtual disks will be created. Figure 10. 4 Array Settings Interface 6. Click Virtual Disk tab to view the automatically created virtual disk. Notes: 1) By default, one-touch configuration adopts foreground initialization to initialize the virtual disk. By using foreground initialization, the virtual disk can be used only after the initialization is complete.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 6 Physical Disk Settings Interface 2. Click Creat button to enter the Create Array interface. Figure 10. 7 Create Array Interface 3. Edit the Array Name; set the RAID Level to RAID 0, RAID 1, RAID 5 or RAID 10; select the Physical Disk that you want to configure array. Notes: 4. 1) If you choose RAID 0, at least 2 HDDs must be installed. 2) If you choose RAID 1, 2 HDDs need to be configured for RAID 1.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 8 Error Message Box 5. You can click Array tab to view the successfully created array. Figure 10. 9 Array Settings Interface 6. Click to select an array and click Creat Vd button to enter the Create Virtual Disk interface. Note: The device supports creating at most 8 virtual disks. Figure 10. 10 Create Virtual Disk Interface 7.
User Manual of DS-9600/8600/7700/7600 Series NVR totally and the bad sector of the hard disks can be detected and repaired. The virtual disk can be used only after the initialization is complete. Background: The background initialization can synchronize the disks, and detect and repair the bad sector of the disks. During the background initialization, the virtual disk is allowed to be used. 8. Click Apply button to save the settings and click OK button to return to Array Settings interface 9.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 14 Physical Disk Settings Interface 13. Select a disk and click to enter the Set Hot Spare interface. Figure 10. 15 Set Hot Spare Interface 14. Set the hot spare type of the selected HDD to Global Hot Spare or the specified hot spare for the existing array. Global Hot Spare: It can be used as the hot spare for any array created in the system. Array Hot Spare (e.g. RAID 5): It can be used as the hot spare for the specified array only. 15.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.2 Rebuilding Array Purpose: The working status of array includes Functional, Degraded and Offline. By viewing the array status, you can take immediate and proper maintenance for the disks so as to ensure the high security and reliability of the data stored in the disk array.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 18 Set Hot Spare Disk Interface 10.2.2 Manually Rebuilding Array Purpose: If you do not enable the Auto-rebuild in Firmware Settings interface (Menu>HDD>RAID>Firmware) or the hot spare disk has not been configured, then you can rebuild the array manually to restore the array when the virtual disk is in Degraded status. Steps: 1. Enter the Array Settings interface. The disk 3 is lost. Menu > HDD > RAID > Array Figure 10.
User Manual of DS-9600/8600/7700/7600 Series NVR Note: At least one available physical disk should exist for rebuilding the array. Figure 10. 21 Rebuild Array Interface 4. Select the available physical disk and click OK button to confirm to rebuild the array. 5. The “Do not unplug the physical disk when it is under rebuilding” message box pops up. Click OK button to start rebuilding. 6. You can enter the Array Settings interface and Virtual Disk interface to view the rebuilding status. 7.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.3 Repairing Virtual Disk Purpose: When the disk cannot display in the HDD Information interface while the virtual disk can still show in the Array Settings interface, you have to repair the virtual disk. Note: If the virtual disk is under foreground initialization, the repairing cannot be done. Steps: 1. Enter the Virtual Disk interface. Menu > HDD > RAID > Virtual Disk Figure 10. 22 Virtual Disk Interface 2. Click to repair the virtual disk.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.4 Deleting Array / Virtual Disk Note: Before deleting the array, the virtual disk(s) existing under this array must be deleted first. Deleting array and virtual disk will cause to delete all the data saved in the disk. 10.4.1 Deleting the Virtual Disk Steps: 1. Enter the Virtual Disk interface. Menu>HDD>RAID>Virtual Disk Figure 10. 25 Virtual Disk Interface 2. Select a virtual disk and click to delete the virtual disk. Figure 10.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 27 Array Settings Interface 2. Select an array and click to delete the array. Figure 10. 28 Confirm Array Deletion 3. In the pop-up message box, click Yes button to confirm the array deletion. Note: Deleting array will cause to delete all the data in the array.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.5 Migrating and Extending Purpose: When the remaining storage space is lower than the actual needs, you can take array migration and online extend to enlarge the capacity of the virtual disk. Before you start: At least one available physical disk should exist for the array migration. Steps: 1. Enter the Physical Disk Settings interface. At least one available physical disk should exist for the array migration. Menu>HDD>RAID>Physical Disk Figure 10.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 31 Migrate Array Interface 4. Select the available physical disk(s) and click OK button to confirm the settings. The message box of “Do not unplug the physical disk when it is under migration” will pop up. Click OK button to start migration. 5. You can enter the Array Settings interface (Menu>HDD>RAID>Array) and Virtual Disk interface (Menu>HDD>RAID>Virtual) to check the process of the migration. Figure 10.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 35 Message Box for Expansion 9. After expanding finished, the following message box pops up. Click OK button to finish the settings. Figure 10. 36 Message Box for Expanding Finished Note: After RAID migration and capacity expansion, the expanded capacity for each virtual disk can be calculated by the following formula: Expanded VD capacity＝(Original VD Capacity / Original Array Capacity) * Newly Added Capacity of Hard Disk.
User Manual of DS-9600/8600/7700/7600 Series NVR 10.6 Upgrading Firmware Purpose: You can view the information of the firmware and upgrade the firmware by local backup device or remote FTP server. Steps: 1. Enter the Firmware interface to check the information of the firmware, including the version, maximum physical disk quantity, maximum array quantity, auto-rebuild status, etc. Figure 10. 37 Firmware Interface 2. You can click Upgrade button to upgrade the firmware.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 11 HDD Management 171
User Manual of DS-9600/8600/7700/7600 Series NVR 11.1 Initializing HDDs Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR. Note: A message box pops up when the NVR starts up if there exits any uninitialized HDD. Figure 11. 1 Message Box of Uninitialized HDD Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD. Steps: 1. Enter the HDD Information interface. Menu > HDD> General Figure 11.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 5 HDD Status Changes to Normal Note: Initializing the HDD will erase all data on it.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.2 Managing Network HDD Purpose: You can add the allocated NAS or disk of IP SAN to NVR, and use it as network HDD. Steps: 1. Enter the HDD Information interface. Menu > HDD>General Figure 11. 6 HDD Information Interface 2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 11. 7. Figure 11. 7 HDD Information Interface 3. Add the allocated NetHDD. 4. Select the type to NAS or IP SAN. 5.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 8 Add NAS Disk • Add IP SAN: 1) Enter the NetHDD IP address in the text field. 2) Click the Search button to search the available IP SAN disks. 3) Select the IP SAN disk from the list shown below. 4) Click the OK button to add the selected IP SAN disk. Note: Up to 1 IP SAN disk can be added. Figure 11. 9 Add IP SAN Disk 6. After having successfully added the NAS or IP SAN disk, return to the HDD Information menu.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.3 Managing eSATA Purpose: When there is an external eSATA device connected to NVR, you can configure eSATA for the use of Record/Capture or Export, and you can manage the eSATA in the NVR. Steps: 1. Enter the Advanced Record Settings interface. Menu >Record>Advanced 2. Select the eSATA type to Export or Record/Capture from the dropdown list of eSATA. Export: use the eSATA for backup.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.4 Managing HDD Group 11.4.1 Setting HDD Groups Purpose: Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Group, as shown in Figure 11. 13. Figure 11. 13 Storage Mode Interface 3. Click the Apply button and the following Attention box will pop up. Figure 11. 14 Attention for Reboot 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 15 Local HDD Settings Interface 7. Select the Group number for the current HDD. Note: The default group No. for each HDD is 1. 8. Click the OK button to confirm the settings. Figure 11. 16 ConfirmHDD Group Settings 9. In the pop-up Attention box, click the Yes button to finish the settings. 11.4.2 Setting HDD Property Purpose: The HDD property can be set to redundancy, read-only or read/write (R/W).
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 17 Set HDD Property 3. Set the HDD property to R/W, Read-only or Redundancy. 4. Click the OK button to save the settings and exit the interface. 5. In the HDD Information menu, the HDD property will be displayed in the list. Note: At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy, and there is one HDD with R/W property.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.5 Configuring Quota Mode Purpose: Each camera can be configured with allocated quota for the storage of recorded files or captured pictures. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Quota, as shown in Figure 11. 18. Note: The NVR must be rebooted to enable the changes to take effect. Figure 11. 18 Storage Mode Settings Interface 3. Select a camera for which you want to configure quota. 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 20 Copy Settings to Other Camera(s) 6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of IP Camera to select all cameras. 7. Click the OK button to finish the Copy settings and back to the Storage Mode interface. 8. Click the Apply button to apply the settings. Note: If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for record and picture capture.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.6 Checking HDD Status Purpose: You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface Steps: 1. Enter the HDD Information interface. Menu > HDD>General 2. Check the status of each HDD which is displayed on the list, as shown in Figure 11. 21. Figure 11.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.7 HDD Detection Note: This function is not supported with DS-9600NI-RT series NVR. Purpose: The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures. S.M.A.R.T. Settings Steps: 1. Enter the S.M.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 11. 24 Bad Sector Detection Note: represents normal sector; represents bad sector detected by Bad Sector Detection; bad sector detected by recording. And you can click Error info button to see the detailed damage information. And you can also pause/resume or cancel the detection.
User Manual of DS-9600/8600/7700/7600 Series NVR 11.8 Configuring HDD Error Alarms Purpose: You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. Steps: 1. Enter the Exception interface. Menu > Configuration > Exceptions 2. Select the Exception Type to HDD Error from the dropdown list. 3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 11. 25.
User Manual of DS-9600/8600/7700/7600 Series NVR 12.1 Configuring OSD Settings Purpose: You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc. Steps: 1. Enter the OSD Configuration interface. Menu > Camera > OSD 2. Select the camera to configure OSD settings. 3. Edit the Camera Name in the text field. 4. Configure the Display Name, Display Date and Display Week by clicking the checkbox. 5. Select the Date Format, Time Format and Display Mode.
User Manual of DS-9600/8600/7700/7600 Series NVR 12.2 Configuring Privacy Mask Purpose: You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy mask can prevent certain surveillance areas to be viewed or recorded. Steps: 1. Enter the Privacy Mask Settings interface. Menu > Camera >Privacy Mask 2. Select the camera to set privacy mask. 3. Click the checkbox of Enable Privacy Mask to enable this feature. Figure 12.
User Manual of DS-9600/8600/7700/7600 Series NVR 12.3 Configuring Video Parameters Steps: 1. Enter the Image Settings interface. Menu > Camera >Image Figure 12. 4 Image Settings Interface 2. Select the camera to set image parameters. 3. You can click on the arrow to change the value of each parameter. 4. Click the Apply button to save the settings.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 13 NVR Management Maintenance 190 and
User Manual of DS-9600/8600/7700/7600 Series NVR 13.1 Viewing System Information 13.1.1 Viewing Device Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. , firmware version and encode version, as shown in Figure 13. 1. Figure 13. 1 Device Information Interface 13.1.2 Viewing Camera Information Steps: 1. Enter the System Information interface.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13. 3 Record Information Interface 13.1.4 Viewing Alarm Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure 13. 4. Figure 13.
User Manual of DS-9600/8600/7700/7600 Series NVR 13.1.5 Viewing Network Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Network tab to enter the Network Information menu to view the network information, as shown in Figure 13. 5. Figure 13. 5 Network Information Interface 13.1.6 Viewing HDD Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13.
User Manual of DS-9600/8600/7700/7600 Series NVR 13.2 Searching & Export Log Files Purpose: The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and exported at any time. Steps: 1. Enter the Log Search interface. Menu >Maintenance>Log Information Figure 13. 7 Log Search Interface 2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and Minor Type. 3. Click the Search button to start search log files. 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Note: Up to 2000 log files can be displayed each time. 5. You can click the button of each log or double click it to view its detailed information, as shown in Figure 13. 9. And you can also click the button to view the related video files if available. Figure 13. 9 Log Details 6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 13. 10. Figure 13. 10 Export Log Files 7.
User Manual of DS-9600/8600/7700/7600 Series NVR 20110514124841logBack.txt. To export all the log files: Steps: 1. Enter the Log Information interface. Menu> Maintenance> Log Information> Log Export 2. Click the Log Export tab. Figure 13. 11 Log Export Interface 3. You can check the checkbox of the HDD. 4. Click the Export button to export all the log files stored in the HDD.
User Manual of DS-9600/8600/7700/7600 Series NVR 13.3 Importing/Exporting Configuration Files Purpose: The configuration files of the NVR can be exported to local device for backup; and the configuration files of one NVR can be imported to multiple NVR devices if they are to be configured with the same parameters. Steps: 1. Enter the Import/Export Configuration File interface. Menu > Maintenance >Import/Export Figure 13. 12 Import/Export Config File 2.
User Manual of DS-9600/8600/7700/7600 Series NVR 13.4 Upgrading System Purpose: The firmware on your NVR can be upgraded by local backup device or remote FTP server. 13.4.1 Upgrading by Local Backup Device Steps: 1. Connect your NVR with a local backup device where the update firmware file is located. 2. Enter the Upgrade interface. Menu >Maintenance>Upgrade 3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 13. 13. Figure 13. 13 Local Upgrade Interface 4.
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13. 14 FTP Upgrade Interface 3. Enter the FTP Server Address in the text field. 4. Click the Upgrade button to start upgrading. 5. After the upgrading is complete, reboot the NVR to activate the new firmware.
User Manual of DS-9600/8600/7700/7600 Series NVR 13.5 Restoring Default Settings Steps: 1. Enter the Default interface. Menu > Maintenance > Default Figure 13. 15 Restore Factory Default 2. Click the OK button to restore the default settings. Note: Except the network parameters (including IP address, subnet mask, gateway, MTU, NIC working mode, default route and server port), all other parameters of the device will be restored to factory default settings.
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 14 Others 202
User Manual of DS-9600/8600/7700/7600 Series NVR 14.1 Configuring RS-232 Serial Port Purpose: The RS-232 port can be used in two ways: • Parameters Configuration: Connect a PC to the NVR through the PC serial port. Device parameters can be configured by using software such as HyperTerminal. The serial port parameters must be the same as the NVR’s when connecting with the PC serial port. • Transparent Channel: Connect a serial device directly to the NVR.
User Manual of DS-9600/8600/7700/7600 Series NVR 14.2 Configuring General Settings Purpose: You can configure the BNC output standard, VGA output resolution, mouse pointer speed through the Menu > Configuration > General interface. Steps: 1. Enter the General Settings interface. Menu >Configuration> General 2. Select the General tab. Figure 14. 2 General Settings Interface 3. Configure the following settings: • Language: The default language used is English.
User Manual of DS-9600/8600/7700/7600 Series NVR 14.3 Configuring DST Settings Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Choose DST Settings tab. Figure 14. 3 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item. Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
User Manual of DS-9600/8600/7700/7600 Series NVR 14.4 Configuring More Settings for Device Parameters Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 14. 4. Figure 14. 4 More Settings Interface 3. Configure the following settings: • Device Name: Edit the name of NVR. • Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the default No. is 255.
User Manual of DS-9600/8600/7700/7600 Series NVR 14.5 Managing User Accounts Purpose: There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is 12345. The Administrator has the permission to add and delete user and configure user parameters. 14.5.1 Adding a User Steps: 1. Enter the User Management interface. Menu >Configuration>User Figure 14. 5 User Management Interface 2. Click the Add button to enter the Add User interface. Figure 14.
User Manual of DS-9600/8600/7700/7600 Series NVR • Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all operating permission in Camera Configuration by default. • Guest: The Guest user has no permission of Two-way Audio in Remote Configuration and only has the local/remote playback in the Camera Configuration by default. User’s MAC Address: The MAC address of the remote PC which logs onto the NVR.
User Manual of DS-9600/8600/7700/7600 Series NVR • Remote Log Search: Remotely viewing logs that are saved on the NVR. • Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters and importing/exporting configuration files. • • • • • Remote Camera Management: Remote adding, deleting and editing of the IP cameras. Remote Serial Port Control: Configuring settings for RS-232 and RS-485 ports. Remote Video Output Control: Sending remote button control signal.
User Manual of DS-9600/8600/7700/7600 Series NVR 14.5.3 Editing a User Steps: 1. Enter the User Management interface. Menu >Configuration>User 2. Select the user to be edited from the list, as shown in Figure 14. 9. 3. Click the icon to enter the Edit User interface, as shown in Figure 14. 10. Note: The admin user can also be edited. Operator and Guest Admin Figure 14. 10 Edit User Interface 4. Edit the corresponding parameters.
User Manual of DS-9600/8600/7700/7600 Series NVR Appendix 211
User Manual of DS-9600/8600/7700/7600 Series NVR Glossary • Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF. • HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters with magnetic surfaces.
User Manual of DS-9600/8600/7700/7600 Series NVR FAQ • Why does my NVR make a beeping sound after booting? The possible reasons for the warning beep on the NVR are as follows: a) There is no HDD installed in the NVR. b) The HDD is not initialized. c) HDD error To cancel the beeping sound and use the NVR without HDD, enter the Exception Settings interface. For detailed information, see Chapter Handling Exceptions Alarm.
User Manual of DS-9600/8600/7700/7600 Series NVR List of Compatible IP Cameras List of Hikvision IP Cameras Supported by DS-9600/8600/7700/7600 Series NVR Note: For the list, our company holds right to interpret. Max. Type Model Version Sub-stream Audio Resolution DS-2CD883F-E V4.0.1 build 120508 2560×1920 √ √ DS-2CD8283F-E(I) V3.0 build110921 2560×1920 √ √ DS-2CD886BF-E V4.0.3 build 120913 2560×1920 √ √ DS-2CD886MF-E V4.0.3 build 120913 2560×1920 √ √ DS-2CD854F-E V4.0.
User Manual of DS-9600/8600/7700/7600 Series NVR DS-2CD833F-E V4.0.1 build 120508 640×480 √ √ DS-2CD8133F-E V4.0.1 build 120508 640×480 √ √ DS-2CD802NF V2.0 build 090522 704×576 √ √ DS-2CD812PF DS-2CD832F Thermal Camera V2.0 build 090715 DS-2CD892PF/NF V2.0 build 110301 DS-2CD893PF(WD)-E V4.0.1 build 120508 704×576 √ √ DS-2CD793PF(WD)-E(I) V4.0.1 build 120508 704×576 √ √ DS-2CD793NF(WD)-E(I) V4.0.1 build 120508 704×576 √ √ DS-2CD8313PF-E40 V3.
User Manual of DS-9600/8600/7700/7600 Series NVR List of Third-party IP Cameras Supported by DS-9600/8600/7700/7600NI-ST Series NVR Note: ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its private protocols. Only ONVIF is supported refers to the camera can only be supported when it uses the ONVIF protocol. IPC Manufacturer Max. Model Version or Protocol Sub-stream Audio Resolution TCM4301-10D-X-00083 A1D-310-V4.12.
User Manual of DS-9600/8600/7700/7600 Series NVR IXE20DN-AAXVUU2 1.8.2-20120327-2.9081-A1.7852 1920×1080 √ × IX30DN-ACFZHB3 1.8.2-20120327-2.9080-A1.7852 2048×1536 √ × SAMSUNG SNB-5000P V2.00_110727 1280×1024 × √ (ONVIF SNB-7000P V1.10_110819 2048×1536 × √ compatibility) SNP-5200 V1.04_110825 1280×1024 √ √ VCC-HD2300P 2.03-02(110318-00) 1920×1080 × × VCC-HD2500P 2.02-02(110208-00) 1920×1080 × √ VCC-HD4600P 2.03-02(110315-00) 1920×1080 × √ VCC-HD5400 2.
