Network Video Recorder Quick Operation Guide UD.
Quick Operation Guide of Network Video Recorder TABLE OF CONTENTS NVR Installation .............................................................................................................................................. 6 Hard Disk Installation ..................................................................................................................................... 6 Front Panel ................................................................................................................
Quick Operation Guide of Network Video Recorder Quick Start Guide COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Quick Operation Guide of Network Video Recorder Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Quick Operation Guide of Network Video Recorder Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Quick Operation Guide of Network Video Recorder Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • • • • • Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf.
Quick Operation Guide of Network Video Recorder Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to the models listed in the following table.
Quick Operation Guide of Network Video Recorder 2. Install the HDD in the HDD rack using the provided screws. Fasten the screws on the button to fix the HDD. 3. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD. 4. Connect the power cable to the HDD. 5. Re-install the cover of the NVR and fasten screws.
Quick Operation Guide of Network Video Recorder Steps (for other models): 1. Remove the cover from the NVR by unfastening the screws on the rear and side panel. 2. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD. 3. Connect the power cable to the HDD. 4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD. 5. Re-install the cover of the NVR and fasten screws.
Quick Operation Guide of Network Video Recorder Front Panel DS-8600NI-E8 No. Name Function Description ALARM READY Turns red when a sensor alarm is detected. Ready LED is normally blue, indicating that the device is functioning properly. Turns blue when device is controlled by an IR remote. STATUS Turns red when controlled by a keyboard and purple when IR remote and keyboard is used at the same time. 1 Status HDD Indicators MODEM Tx/Rx Flashes red when data is being read from or written to HDD.
Quick Operation Guide of Network Video Recorder No. Name Function Description Adjust focus in the PTZ Control menu. A/FOCUS+ It is also used to switch between input methods (upper and lowercase alphabet, symbols and numeric input). Edit text fields. When editing text fields, it will also function as a Backspace button to delete the character in front of the cursor. On checkbox fields, pressing the button will tick the checkbox. EDIT/IRIS+ In PTZ Control mode, the button adjusts the iris of the camera.
Quick Operation Guide of Network Video Recorder No. Name Function Description the video by a single frame. In Auto-switch mode, it can be used to stop /start auto switch. Move the active selection in a menu. It will move the selection up and down. In Live View mode, it can be used to cycle through different channels. 8 JOG SHUTTLE Control In the Playback mode: The outer ring is used to speed up or slow down the record files and the inner ring is used to jump 30s forward/backward in records files.
Quick Operation Guide of Network Video Recorder No. Name Function Description resume auto sequence. Switch between the numeric or letter input and functions of the SHIFT composite keys. (Input letter or numbers when the light is out; Realize functions when the light is red.) 1/MENU Enter numeral “1”; Access the main menu interface. Enter numeral “2”; Enter letters “ABC”; 2/ABC/F1 The F1 button when used in a list field will select all items in the list.
Quick Operation Guide of Network Video Recorder No. Name Function Description In PTZ control mode, it can control the movement of the PTZ camera. 6 POWER ON/OFF 7 USB Interfaces Power on/off switch. Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). DS-7600NI-E1/E2 Series No. Name Description Power 1 Status Indicator Status Tx/Rx Power indicator turns yellow when system is running.
Quick Operation Guide of Network Video Recorder Rear Panel The rear panel vaires according to different models. DS-8600NI-E8, DS-7700NI-E4 and DS-7700NI-E4/P DS-8600NI-E8 and DS-7700NI-E4 DS-7700NI-E4/P No. Item Description 1 LAN Interface 1 network interface provided for DS-7700NI-E4/P and 2 network interfaces for DS-7700NI-E4 and DS-8600NI-E8. 2 AUDIO OUT RCA connector for audio output. 3 LINE IN RCA connector for audio input. 4 HDMI HDMI video output connector. 5 USB 3.
Quick Operation Guide of Network Video Recorder DS-7600NI-E1, DS-7600NI-E1/4N, DS-7600NI-E2 and DS-7600NI-E2/8N DS-7600NI-E1/E2 DS-7600NI-E1/4N DS-7600NI-E2/8N No. Item Description 1 Power Supply DC 12V power supply. 2 Audio In RCA connector for audio input. 3 HDMI Interface HDMI video output connector. 4 LAN Network Interface 1 10 /100 /1000 Mbps self-adaptive Ethernet interface 5 Audio Out RCA connector for audio output. 6 VGA Interface DB9 connector for VGA output.
Quick Operation Guide of Network Video Recorder DS-7600NI-E2/8P No. Item Description 1 Power Supply 48V DC power supply for DS-7600NI-E1/4P and AC 100~240V for DS-7600NI-E2/8P. 2 Audio In RCA connector for audio input. 3 HDMI Interface HDMI video output connector. 4 LAN Network Interface 1 10 /100 /1000 Mbps self-adaptive Ethernet interface 5 Audio Out RCA connector for audio output. 6 VGA Interface DB9 connector for VGA output. Display local video output and menu.
Quick Operation Guide of Network Video Recorder Peripheral Connections This section is applicable for the DS-8600NI-E8, DS-7700NI-E4 and DS-7700NI-E4/P series only. Wiring of Alarm Input The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device.
Quick Operation Guide of Network Video Recorder Specifications Specifications of DS-8600NI-E8 Model Video/Audio input Network DS-8608NI-E8 DS-8616NI-E8 DS-8632NI-E8 IP video input 8-ch 16-ch 32-ch Two-way audio 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7700NI-E4 Model Video/Audio input Network DS-7708NI-E4 DS-7716NI-E4 DS-7732NI-E4 IP video input 8-ch 16-ch 32-ch Two-way audio 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7700NI-E4/P Model Video/Audio input Network DS-7708NI-E4/8P DS-7716NI-E4/16P DS-7732NI-E4/16P IP video input 8-ch 16-ch 32-ch Two-way audio 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7600NI-E2 Model DS-7608NI-E2 DS-7616NI-E2 DS-7632NI-E2 16-ch 32-ch Video/Audio IP video input 8-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7600NI-E1 Model DS-7604NI-E1 DS-7608NI-E1 DS-7616NI-E1 8-ch 16-ch Video/Audio IP video input 4-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7604NI-E1/N and DS-7608NI-E2/N Model DS-7604NI-E1/4N DS-7608NI-E2/8N 8-ch Video/Audio IP video input 4-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7616&7632NI-E2/N DS-7616NI-E2/ DS-7632NI-E2/ DS-7616NI-E2/ DS-7632NI-E2/ 8N 8N 16N 16N 32-ch 16-ch 32-ch Model Video/Audio IP video input 16-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7604NI-E1/P and DS-7608NI-E2/P Model DS-7604NI-E1/4P DS-7608NI-E2/8P 8-ch Video/Audio IP video input 4-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder Specifications of DS-7616&7632NI-E2/P DS-7616NI-E2/ DS-7632NI-E2/ DS-7616NI-E2/ DS-7632NI-E2/ 8P 8P 16P 16P 32-ch 16-ch 32-ch Model Video/Audio IP video input 16-ch input Two-way audio input 1-ch, RCA (2.
Quick Operation Guide of Network Video Recorder HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate 96K 128K 160K 192K 224K 256K 320K 384K 448K 512K 640K 768K 896K 1024K 1280K 1536K 1792K 2048K Storage Used 42M 56M 70M 84M 98M 112M 140M 168M 196M 225M 281M 337M 393M 450M 562M 675M 787M 900M 4096K 1.8G 8192K 3.6G 16384K 7.
Quick Operation Guide of Network Video Recorder Menu Operation Menu Structure The menu structure is shown as follows: Menu Playback Export VCA Search Manual HDD Record Camera Configuration Maintenance Shutdown Normal Normal Behavior Search Record General Schedule Camera General System Info Logout Event Event Face Search Alarm Advanced Parameters OSD Network Log Information Shutdown Reboot Tag People Counting Advanced Image Alarm Import/ Export Smart Heat Map Holiday
Quick Operation Guide of Network Video Recorder 2. Select the Shutdown button. 3. Click the Yes button. 4. Turn off the power switch on the rear panel when the attention pops up. Setting the Admin Password Purpose: For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation. You can also activate the device via Web Browser, SADP or Client Software. Steps: 1.
Quick Operation Guide of Network Video Recorder Login and Logout User Login Purpose: If NVR has logged out, you must login the device before operating the menu and other functions. Steps: 1. Select the User Name in the dropdown list. 2. Input Password. 3. Click OK to log in. The device gets locked for 60 seconds if the admin user performs 7 failed password attempts (5 attempts for the guest/operator).
Quick Operation Guide of Network Video Recorder 2. Click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system. Live View Some icons are provided on screen in Live View mode to indicate different camera status.
Quick Operation Guide of Network Video Recorder 3. Select the detected IP camera and click the Add button to add it directly, and you can click the Search button to refresh the online IP camera manually. Or you can choose to custom add the IP camera by editing the parameters in the corresponding textfiled and then click the Add button to add it. OPTION 2: Steps: 1.
Quick Operation Guide of Network Video Recorder 2) You can edit the IP address, protocol, management port, and other information of the IP camera to be added. 3) Click Add to add the camera. For the successfully added IP cameras, the Security status shows the security level of the password of camera: strong password, weak password and risk password. Explanation of the icons Icon Explanation Icon Edit basic parameters of the camera Explanation Add the detected IP camera.
Quick Operation Guide of Network Video Recorder Recording Before you start: Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. You can refer to the user manual for detailed information. Purpose: Two kinds of record types are introduced in the following section, including Instant Record and All-day Record. And for other record types, you may refer to the user manual for detailed information. After rebooting all the manual records enabled are canceled.
Quick Operation Guide of Network Video Recorder Option 2: Steps: 1. Enter the Playback menu. Mouse: right click a channel in live view mode and select Playback from the menu. Front Panel (not applicable for the DS-7600NI-E1/E2 series): press PLAY button to play back record files of the channel under single-screen live view. Under multi-screen live view, record files of the selected channel will be played back. Pressing numerical buttons will switch playback to related channels during playback process.
Quick Operation Guide of Network Video Recorder Just check the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels. Backup Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer. Steps: 1. Enter Video Export interface. Choose the channel(s) you want to back up and click on the Quick Export button. 2.
Quick Operation Guide of Network Video Recorder VCA Detection Purpose: The NVR supports the VCA detection alarm (face detection, vehicle detection, line crossing detection and intrusion detection, region entrance detection, region exiting detection, loitering detection, people gathering detection, fast moving detection, parking detection, unattended baggage detection, object removal detection, audio loss exception detection, sudden change of sound intensity detection, and defocus detection) sent by IP came
Quick Operation Guide of Network Video Recorder VCA Search The NVR supports the VCA search for the behavior analysis, face capture, people counting and heat map. Face Search: Search the captured face picture results triggered by face detection. Behavior Search: Search and view the behavior detection (including the line crossing detection, intrusion detection, unattended baggage detection, etc.) results in pictures and video files.
Quick Operation Guide of Network Video Recorder Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Logging In You can get access to the device via web browser.
Quick Operation Guide of Network Video Recorder prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. Live View The live view interface appears by default when you log in the device. 2 1 4 3 The live view interface may differ according to different models. Interface Introduction No. Name 1 Channel List 2 3 Live View Window Play Control Bar Description Displays the list of channels and the playing and recording status of each channel.
Quick Operation Guide of Network Video Recorder Icon Description Icon Select the window-division mode / Start/Stop all live view / Description / Capture pictures in the live view Start/Stop all recording / Previous/Next page / Start/Stop two-way Audio Adjust volume mode / Open/Close audio Enable/Disable digital zoom Full screen Select different stream type for live view by clicking the icon : live view in main stream; : live view in sub stream; Recording Before you start Make sure the
Quick Operation Guide of Network Video Recorder 2) Select the Record Type for the period. The record type can be Schedule, Motion, Alarm, Motion & Alarm, Motion | Alarm and Event. 3) Click Save to save the settings. 4) Click the required. 5) Click OK to save the settings. icon of the day to copy the settings of current day to other days of the week if 5. Click Advanced to configure advanced record parameters, and click the OK button to save the settings. 6.
Quick Operation Guide of Network Video Recorder Playback The playback interface may differ according to different models. Interface Introduction No. Name Description 1 Channel List Displays the list of channels and the playing status of each channel. Playback Displays the image of channel. 2 Window 3 Play Control Bar Play control operations are supported. 4 Time Line Displays the time bar and the records marked with different colors.
Quick Operation Guide of Network Video Recorder Button Description Button Stop all playback / Download Start/Stop video clipping / Full screen 6. Description Open/Close audio Reverse playback You can drag the progress bar with the mouse to locate the exact playback point. You can also input the time in the textbox and click button to locate the playback point. The color of the video on the progress bar stands for the different video types.
Quick Operation Guide of Network Video Recorder 0300061040722 45