Digital Video Recorder Quick Start Guide UD03984B
Digital Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description .............................................................................7 1.1 Front Panel ...................................................................................................7 1.2 Rear Panel ..................................................................................................14 Chapter 2 Installation and Connections........................................................... 19 2.
Digital Video Recorder Quick Start Guide Quick Start Guide COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Digital Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Digital Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table.
Digital Video Recorder Quick Start Guide DS-7200HUHI-F2/N DS-7200HUHI-F1/S DS-7200HUHI-F2/S DS-7600HUHI-F2/N DS-7300HUHI-F4/N DS-8100HUHI-F8/N DS-9000HUHI-F8/N DS-9000HUHI-F16/N DS-7204HUHI-F2/N DS-7208HUHI-F2/N DS-7216HUHI-F2/N DS-7204HUHI-F1/S DS-7208HUHI-F1/S DS-7204HUHI-F2/S DS-7208HUHI-F2/S DS-7216HUHI-F2/S DS-7604HUHI-F1/N DS-7608HUHI-F2/N DS-7616HUHI-F2/N DS-7304HUHI-F4/N DS-7308HUHI-F4/N DS-7316HUHI-F4/N DS-8104HUHI-F8/N DS-8108HUHI-F8/N DS-8116HUHI-F8/N DS-9004HUHI-F8/N DS-9008HUHI-F8/N DS-9
Digital Video Recorder Quick Start Guide Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Digital Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel The front panel vaires according to different models. Please refer to the actual product. The following figures only take examples of several models. Front Panel 1 Figure 1-1 Front Panel 1 Table 1-1 Description of Front Panel 1 No. Icon Description 1 Turns red when DVR is powered up. 2 Turns red when data is being read from or written to HDD. 3 Flickers blue when network connection is functioning properly.
Digital Video Recorder Quick Start Guide Table 1-2 Description of Front Panel 2 No. Name POWER Turns yellow when the power switch on the rear panel is turned on. STATUS Flickers red when data is being read from or written to HDD. Tx/Rx Flickers yellow when functioning properly. 2 IR Receiver Receiver for IR remote 3 USB Interfaces Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD).
Digital Video Recorder Quick Start Guide Turns on/off PTZ light in PTZ Control mode, and use it to zoom out the image; Switches between main and spot video output in live view or playback mode. Enters numeral “3”; 3/DEF/F2 Enters letters “DEF”; Uses the F2 button to change the tab pages; Zooms in the image in PTZ control mode. Enters numeral “4”; 4/GHI/ESC Enters letters “GHI”; Exits and back to the previous menu.
Digital Video Recorder Quick Start Guide Multi-channel display in live view. Enters numeral “0”; 0/A Shifts the input methods in the editing text field. (Upper and lowercase, alphabet, symbols or numeric input). Navigates between different fields and items in menus. Uses the Up and Down buttons to speed up and slow down the playing of video files in Playback mode. DIRECTION The Left and Right button will select the next and previous record files. Cycles through channels in Live View mode.
Digital Video Recorder Quick Start Guide Figure 1-4 Front Panel 4 Front Panel 5 Figure 1-5 Front Panel 5 Table 1-4 Description of Front Panel 4 and 5 No. Name Function Description ALARM Turns red when a sensor alarm is detected. READY Turns green, indicating that the DVR is functioning properly. Turns blue when device is controlled by an IR remote. STATUS 1 Turns red when controlled by a keyboard and purple when IR remote and keyboard is used at the same time.
Digital Video Recorder Quick Start Guide time, an alarm is enabled when an event is detected. GUARD Turns off when the device is unarmed. The arm/disarm status can be changed by pressing and holding on the ESC button for more than 3 seconds in live view mode. Turns red when a sensor alarm is detected. 2 IR Receiver Receiver for IR remote 3 Front Panel Lock Lock or unlock the panel by the key. 4 DVD-R/W Slot for DVD-R/W. Switches to the corresponding channel in live view or PTZ control mode.
Digital Video Recorder Quick Start Guide Switches between input methods (upper and lower case alphabet, symbols and numeric input). Edits text fields. When editing text fields, it also deletes the character in front of the cursor. Checks the checkbox in the checkbox fields. EDIT/IRIS+ Adjusts the iris of the camera in PTZ control mode. Generates video clips for backup in playback mode. Enters/exits the folder of USB device and eSATA HDD. MAIN/SPOT/ZOOM- Switches between main and spot output.
Digital Video Recorder Quick Start Guide Uses the Up and Down buttons to speed up and slow down the playing of video files in Playback mode. The Left and Right button will select the next and previous record files. Cycles through channels in Live View mode. Controls the movement of the PTZ camera in PTZ control mode. Confirms selection in any of the menu modes. Checks the checkbox. ENTER Plays or pauses the playing of video files in Playback mode.
Digital Video Recorder Quick Start Guide Figure 1-6 Rear Panel 1 Table 1-5 Description of Rear Panel 1 No. Item VIDEO IN BNC interface for Turbo HD and analog video input. 2 AUDIO IN RCA connector 3 AUDIO OUT RCA connector. VGA DB15 connector for VGA output. Display local video output and menu. HDMI HDMI video output connector. USB Port Universal Serial Bus (USB) port for additional devices. 7 Network Interface Connector for network 8 RS-485 Interface Connector for RS-485 devices.
Digital Video Recorder Quick Start Guide Figure 1-7 Rear Panel 2 Table 1-6 Description of Rear Panel 2 No. Item 1 Function Description VIDEO IN BNC interface for TVI and analog video input. VIDEO OUT BNC connector for video output. 2 CVBS output is not provided for DS-7100/7200HGHI-E1, DS-7200HGHI-E2, DS-7100/7200HGHI-F1, DS-7200HGHI-F2, DS-7100HQHI-F1/N and DS-7100HGHI-F1/N series DVR. AUDIO IN RCA connector USB Port Universal Serial Bus (USB) port for additional devices.
Digital Video Recorder Quick Start Guide No. Item Function Description 11 Power Switch Switch for turning on/off the device. 12 GND Ground 13 LINE IN BNC connector for audio input. 14 eSATA Connects external SATA HDD, CD/DVD-RW. 15 RS-232 Interface Connector for RS-232 devices. Rear Panel 3 Figure 1-8 Rear Panel 3 Table 1-7 Description of Rear Panel 3 No. Item Description 1 VIDEO IN BNC interface for TVI and analog video input. VIDEO OUT BNC connector for video output.
Digital Video Recorder Quick Start Guide 6 HDMI2 HDMI2 video output connector. 7 AUDIO OUT BNC connector. 8 Network Interface Connector for network Connector for RS-485 devices. T+ and T- pins connect to R+ and R- pins of PTZ receiver respectively. 9 RS-485 and Interface Alarm D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first DVR’s D+, D- pin should be connected with the D+, D- pin of the next DVR. Connector for alarm input. Connector for alarm output.
Digital Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 DVR Installation During installation of the DVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the DVR is grounded.
Digital Video Recorder Quick Start Guide Figure 2-1 Fasten Hard Disk Step 2 Connect one end of the data cable to the motherboard of DVR and the other end to the HDD. Figure 2-2 Insert Panel Key Step 3 Connect the power cable to the HDD. Figure 2-3 Open Panel Lock Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
Digital Video Recorder Quick Start Guide Figure 2-4 Insert Hard Disk Step 5 Re-install the cover of the DVR and fasten screws.
Digital Video Recorder Quick Start Guide 2.3 RS-485 and Controller Connection Typical Connection: Figure 2-5 Controller Connection A To connect PTZ to the DVR: Step 1 Disconnect pluggable block from the RS-485 terminal block. Step 2 Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part. Ensure signal cables are in tight. Step 3 Connect A+ on PTZ to D+ on terminal block and B- on controller to D- on terminal block. Fasten stop screws.
Digital Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 96K 42M 128K 56M 160K 70M 192K 84M 224K 98M 256K 112M 320K 140M 384K 168M 448K 196M 512K 225M 640K 281M 768K 337M 896K 393M 1024K 450M 1280K 562M 1536K 675M 1792K 787M 2048K 900M 4096K 1.76G 8192K 3.52G 16384K 7.
Digital Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Menu Structure The menu structure varies according to different models.
Digital Video Recorder Quick Start Guide Step 2 Press the POWER button on the front panel. The Power LED should turn blue. The unit will begin to start. After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording. To shut down the DVR: Step 1 Enter the Shutdown menu. Menu > Shutdown Figure 3-2 Shutdown Step 2 Select the Shutdown button. Step 3 Click the Yes button. 3.
Digital Video Recorder Quick Start Guide STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Digital Video Recorder Quick Start Guide Figure 3-6 Export GUID Step 5 After exporting GUID, the Attention box pops up as below. Click Yes to duplicate the password or No to cancel it. Figure 3-7 Duplicate the Password 3.4 Using the Unlock Pattern for Login For the Admin user, you can configure the unlock pattern for device login. After the device is activated, you can enter the following interface to configure the device unlock pattern.
Digital Video Recorder Quick Start Guide Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully. Step 3 You can use the configured unlock pattern for future login. Figure 3-9 Draw the Unlock Pattern 3.5 Login and Logout 3.5.1 User Login Purpose: If DVR has logged out, you must log in to the device before operating the menu and other functions.
Digital Video Recorder Quick Start Guide Step 3 Click OK to log in. Clear-text password is supported. Click the icon and you can see the clear text of the password. Click the icon again and the content of the password restores invisible. In the Login interface, for the admin, if you have entered the wrong password for 7 times, the account will be locked for 60 seconds. For the operator, if you have entered the wrong password for 5 times, the account will be locked for 60 seconds.
Digital Video Recorder Quick Start Guide Figure 3-14 Reset Password 2) Input the new password and confirm the password. 3) Click OK to save the new password. Then the Attention box pops up as shown below. Figure 3-15 GUID File Imported 4) Click OK and the Attention box as below pops up to remind you to duplicate the password of the device to IP cameras that are connected with default protocol. Click Yes to duplicate the password or No to cancel it.
Digital Video Recorder Quick Start Guide Menu > Shutdown Figure 3-17 Logout Step 2 Click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system. 3.6 Using the Setup Wizard The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded. Check the checkbox to enable Setup Wizard when device starts.
Digital Video Recorder Quick Start Guide Purpose For DS-7200HUHI-F/S series DVR, you can view the analog signal input channels and types and the connectable maximum IP camera number, and configure 5MP long distance transmission. Step 1 Enter the Signal Input Status interface. Menu > Camera > Signal Input Status Figure 3-19 View Signal Input Type (2) Step 2 View the analog signal input channels and types, and the connectable maximum IP camera number.
Digital Video Recorder Quick Start Guide For –F series DVR, you do not need to configure the signal inputs. The analog signal inputs (Turbo HD, AHD, HDCVI, CVBS) and IP signal input can be recognized and connected automatically. For HQHI series DVR, the 3 MP signal can be accessed for the first channel of DVR with 4-ch video inputs, the first 2 channels of DVR with 8-ch video inputs and the first 4 channels of DVR with 16-ch video inputs.
Digital Video Recorder Quick Start Guide Step 2 Select the General tab. Step 3 In the General Settings interface, you can configure the following settings: Working Mode (applicable for DS-8100HQHI-F/N and DS-7300/8100/9000HUHI-F/N series), NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server. Step 4 If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server.
Digital Video Recorder Quick Start Guide Figure 3-22 Add IP Camera Step 2 Select the IP camera from the list and click the admin password of the DVR’s). button to add the camera (with the same Step 3 (Optional) Check the checkbox of Enable H.265 (For Initial Access) for the connected IP camera supporting H.265. Then the IP camera will be encoded with H.265. Enable H.265 option is only applicable to DS-7300/8100/9000HUHI-F/N series DVR.
Digital Video Recorder Quick Start Guide You can choose to custom add the IP camera by editing the parameters in the corresponding text field and then click the Add button to add it. For the –F series DVR, IP camera of 4K resolution can be added, such as 4K bullet camera and PanoVu series camera. 3.10 Live View Icons are provided on screen in Live View mode to indicate camera status.
Digital Video Recorder Quick Start Guide Figure 3-24 Start Recording from Right-click Menu Step 2 Click the Yes button in the pop-up Attention message box to confirm the settings. All the channels will start to record in the selected mode. 3.12 Playback The recorded video files and pictures on the hard disk can be played back in the following modes: instant playback, all-day playback for the specified channel, and playback by normal/event/smart/tag/system logs/sub-periods/external file search/picture.
Digital Video Recorder Quick Start Guide The POS overlay function is only supported by DS-7300/8100HQHI-F/N and DS-7300/8100/9000HUHI-F/N series DVR. When the POS is enabled in playback, the POS information will be overlaid on the video. For DS-7200HUHI-F/S series DVR, you can click to show the VCA information in the smart playback. Then the configured line or quadrilateral in VCA configuration and target frame(s) will be shown on the playback interface. Click to hide the VCA information.
Digital Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose You can get access to the device via web browser.
Digital Video Recorder Quick Start Guide If the device is already activated, enter the user name and password in the login interface, and click the Login button. Figure 4-2 Login Step 3 Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Digital Video Recorder Quick Start Guide 41
