DS-HD1 Wi-Fi Video Doorbell Quick Start Guide https://us.hikvision.
Copyright © 2018–2019 Hikvision USA Inc. and Hikvision Canada Inc. About this Manual The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the Hikvision Website (https://us.hikvision.com/en).
limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Quick Setup Power Kit Installation Doorbell Installation Doorbell Setup
What’s in the Box Mounting Plate (x3) Pick the one for best surveillance angle. Doorbell (x1) Faceplate (x3) Pick the one that best matches your home, from three faceplates. Screwdriver (x1) Plate Foam (x2) Stabilize the mounting plate when installing it on a rough surface.
• If you have a mechanical chime installed in your home, install the power kit and doorbell. • If you have an electronic chime installed in your home, refer to its manual to install the power kit, and install the doorbell. • If no chime is installed, skip power kit installation, install the doorbell, and follow Option B on page 5. Power Kit Installation 1 Shut off the electricity at the breaker that controls the doorbell’s circuit. 3 Remove the cover from your mechanical chime.
5 Connect the wire harness to the chime’s terminals named TRANS and FRONT. 6 Insert the existing chime wire and the other end of the wire harness into the wire connector, and twist it tightly. Repeat this step with the other chime wire. Wire Connector Chime Wire Wiring Overview REAR TRANS FRONT REAR TRANS FRONT DO NOT OIL Chime Wire Chime Wire 7 8 Mount the power kit to the side of the chime. 3 Replace the chime cover.
Doorbell Installation Recommended Installation Height: 1.2 m (4 ft) above the ground. 1 Shut off the electricity at the breaker that controls the 2 (Optional) If the wall is uneven, paste the plate foam to the mounting plate. doorbell’s circuit. 3 Insert the mini-level into the mounting plate, and 4 Drill holes according to the drill points, and insert anchors. mark the drill points when its bubble stays centered. Mini-Level Remove the mini-level when drill points are marked.
5 Affix the mounting plate to the wall. 6 Remove faceplate on your doorbell from bottom to top. Mounting Screw 7 If you have a chime installed, follow Option A; if not, follow Option B. Option A Connect doorbell to your existing doorbell wires. Fixing Screw U-Shaped Wire Option B Connect the fuse wire to your existing doorbell wire.
8 Fix the doorbell to the mounting plate by inserting the 9 doorbell screws. Restore the electricity at the breaker. Doorbell Screw • Doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity is off and check the wiring. If yes, proceed to doorbell setup. • For the first time use, please power on the doorbell and wait for 3 hours before using it, or the chime in your home may not work. Doorbell Setup 1 Add to the Hik-Connect app (v3.12.0+).
2 Replace the faceplate and insert two security screws into the bottom of the doorbell to secure the faceplate. Appendix Security Screw Basics MicroSD Card Slot Mounting Holes Terminals Reset Button Hold for 5s to reset and enter AP mode.
Use AP Mode for Wi-Fi Configuration -For AP hotspot configuration, press the Reset button for 5 seconds, and then you will hear a voice prompt. -Wait for a few seconds, until you see the LED indicator flashing blue. -Follow the voice prompt to connect Wi-Fi. Wi-Fi Name: softap_XXXXXXXXX (9-digit Serial No.) Default Password: softap_XXXXXX (Verification Code) eg. Default Password: softap_ABCDEF Serial No. and verification code are listed on the cover of this manual.
Connecting the Doorbell to an NVR The DS-HD1 Doorbell can be connected to a Hikvision NVR for viewing and recording. 1. Open the NVR interface (i.e., Web, local, or iVMS-4200 client). 2. Go to Camera Management Management.. NOTE: The Camera Management interface location varies by NVR model. 3. Click the Custom Add tab on the title bar to enter the Add IP Camera (Custom) interface. Add IP Camera (Custom) IP Camera Address Protocol 110.110.1.
