DS-K1100 Series Card Reader User Manual
DS-K1100 Series Card Reader User Manual © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
DS-K1100 Series Card Reader rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
DS-K1100 Series Card Reader Regulatory Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
DS-K1100 Series Card Reader 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
DS-K1100 Series Card Reader Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage.
DS-K1100 Series Card Reader vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20℃ to 65℃. The device cover for indoor use shall be kept from rain and moisture.
DS-K1100 Series Card Reader reader, you must use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield. If you need to install several card readers, the distance among them must over 30cm. To reduce the noise in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal.
DS-K1100 Series Card Reader Content Chapter 1 Introduction ........................................................ 1 1.1 Front View ..................................................................... 1 1.2 Rear View ...................................................................... 3 1.3 Slide View...................................................................... 5 Chapter 2 Installation.......................................................... 7 2.1 Installing PSAM Card .................
DS-K1100 Series Card Reader Chapter 1 Introduction DS-K1100 series card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a build-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment. 1.
DS-K1100 Series Card Reader The front view of DS-K1102 series card reader is shown below: Figure 1-3 DS-K1102MK/DS-K1102CK Figure 1-4 DS-K1102M/DS-K1102C The front view of DS-K1103 series card reader is shown below: Figure 1-5 DS-K1103MK/DS-K1103CK 2 Figure 1-6 DS-K1103M/DS-K1103C
DS-K1100 Series Card Reader The front view of DS-K1104 series card reader is shown below: Figure 1-7 DS-K1104MK/DS-K1104CK Figure 1-8 DS-K1104M/DS-K1104C 1.
DS-K1100 Series Card Reader 3 1 4 5 Figure 1-10 Rear View of DS-K1102 Series 1 4 3 5 Figure 1-11 Rear View of DS-K1103 Series 4
DS-K1100 Series Card Reader 4 3 5 1 Figure 1-12 Rear View of DS-K1104 Series Table 1-1 Description of Rear View No. Name 1 Cable Interface of RS-485, Power, LED Control, etc. 2 Buzzer 3 Tamper-proof Module 4 DIP Switch 5 PSAM Card Slot (available for CPU card reader) 1.
DS-K1100 Series Card Reader Figure 1-13 DS-K1101 Series Figure 1-14 DS-K1102 Series Figure 1-15 DS-K1103 Series Figure 1-16 DS-K1104 Series 6
DS-K1100 Series Card Reader Chapter 2 Installation 2.1 Installing PSAM Card PSAM card slot is only available for CPU card reader. Insert the PSAM card into the slot according to the direction shown below. Figure 2-1 PSAM Card Slot 2.2 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8.
DS-K1100 Series Card Reader Figure 2-3 DIP Switch Module Table 2-2 Description of DIP Switch No. 1~4 Description DIP Switch Status 1: 1 0: 0 Address of RS-485 Read card No. or file in card. (Only available for CPU card reader.) Wiegand protocol or RS-485 protocol. 5 6 7 Wiegand Protocol (available when No. 6 is 1) 8 Matched Resistance (available for RS-485 protocol) 1: read card No; 0: read file in card. 1: Wiegand protocol; 0: RS-485 protocol.
DS-K1100 Series Card Reader Color Purple Gray Green White Black Orange Red Description Beep Control (available for Wiegand Protocol) Case Sensor (available for Wiegand Protocol) Wiegand W0 (available for Wiegand Protocol) Wiegand W1 (available for Wiegand Protocol) GND Red LED Control (available for Wiegand Protocol) PWR (DC +12V) 2.4 Wiring Cables Purpose: Wire the cables between controller and card reader, thus to establish the communication between them. Steps for RS-485 communication mode: 1.
DS-K1100 Series Card Reader Black Red Black Blue Yellow Controller Card Reader Figure 2-4 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode: 1. Set the DIP switch of No. 6 as 1. 2. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, please refer to 2.2 Introduction for DIP Switch. 3. Wiring the cable between controller and card reader as shown below.
DS-K1100 Series Card Reader Brown Purple Orange White Red Green Black Controller Card Reader Figure 2-5 Wiring for Wiegand Communication Mode 2.5 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 2.2 Introduction for DIP Switch.
DS-K1100 Series Card Reader 1. Fix the gang box on the wall or other place. 2. Connect the cables between controller and card reader. For details, refer to 2.4 Wiring Cables. Push the card reader to match the fixed gang box. Fasten the screw to keep the components together. Fix the side cover onto the card reader, press the cover to make it tightly fit the reader. 3. 4. 5.
DS-K1100 Series Card Reader Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn blue and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. During using the card reader, it will send out different sounds prompt and the LED indicator on it have different statuses. You can refer to tables below for detailed information.
DS-K1100 Series Card Reader LED Indicator Status Solid red Red and blinking Red and Keeping rapidly blinking Description card is valid. The operation of pressing keys or swiping card is invalid. For RS-485 protocol: Registering failed or card reader is offline. Failed to get key files of PSAM card; Failed to detect the PSAM card. Available for reading file mode of CPU card: PSAM is not inserted or undetected.
DS-K1100 Series Card Reader UD05659B-A 15
