DS-K1F600-D6E Series Enrollment Station User Manual UD16571B-A
Legal Information User Manual ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website ( https://www.
A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.
Available Model Product Name Model Description DS-K1F600-D6E Supports enroll face and card No. DS-K1F600-D6E-F Supports enroll face, fingerprint, and card No.
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Cautions: Follow these precautions to prevent potential injury or material damage. Dangers: Follow these safeguards to prevent serious injury or death.
equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). • Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. • The device cover for indoor use shall be kept from rain and moisture.
Contents 1 Overview .................................................................. 1 2 Appearance .............................................................. 1 3 Activation ................................................................. 2 3.1 Activate via Device ................................................ 2 3.2 Activate via SADP .................................................. 3 4 Enroll Administrator's Face ....................................... 4 5 Enroll via Device ......................
7.6.1 Import User ............................................... 20 7.6.2 Export Enrolled Data .................................. 21 7.6.3 Clear Enrolled Data .................................... 21 7.7 System Maintenance .......................................... 22 A. Tips When Collecting/Comparing Face Picture ....... 24 B. Tips for Scanning Fingerprint ................................. 25 C. Communication Matrix and Device Command .......
1 Overview Introduction Figure 1-1 Product Appearance The enrollment station can realize multiple user information's enrollment on one device. It supports enrolling face picture, fingerprint (parts of the device model support), 13.56 MHz IC card No., and 125KHz ID card No. Features • 3.97-inch LCD touch screen for face recognition, parameters configuration, live view, etc. • 2 MP wide-angle dual-lens • Face anti-spoofing • Face recognition distance: 0.
Table 2-1 Appearance Description No. Description 1 PSAM3 Card Slot (Reserved) 2 PSAM4 Card Slot (Reserved) 3 Screen 4 Camera 5 Supplement Light 6 Camera 7 USB Interface 8 Network Interface 9 Power Interface 10 PSAM Card Slot (Reserved) 11 PSAM Card Slot (Reserved) 12 Debugging Port 13 Fingerprint Module 14 Card Presenting Area 15 Indicator 3 Activation You should activate the device before the first login.
Figure 3-1 Activation Page Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 4 Enroll Administrator's Face After activation, you should enroll an administrator's face for further operation.
Before You Start • Power on and activate the device. For details about the activation, see Activation. • Enable Face Required in Set Enrollment Rule after logging in the device backend. Steps 1. Tap on the initial page. 2. Optional: If you have added an administrator's face in Add Administrator and enabled Verify by Administrator in Set Enrollment Rule, you should verify the administrator's permission.
Steps 1. Tap on the initial page. 2. Optional: If you have added an administrator's face in Add Administrator and enabled Verify by Administrator in Set Enrollment Rule, you should verify the administrator's permission. Figure 5-2 Authenticate Administrator Page - Make sure the face is in the face recognition frame when authentication. Note For details about face recognition, see Tips When Collecting/Comparing Face Picture. - Tap on the right side and enter the administrator's name and password. 3.
Figure 5-3 Authenticate Administrator Page - Make sure the face is in the face recognition frame when authentication. Note For details about face recognition, see Tips When Collecting/Comparing Face Picture. - Tap on the right side and enter the administrator's name and password. 3. Enroll card. - Present card on the card presenting area and tap OK in the dialogue box. Create an employee ID and tap Next. - Create an employee ID in the input box, and tap Add to enter the User Enrollment page.
Figure 6-2 Add Organization 3) Create an organization name. Note Up to 10 levels of organizations can be added. The added organizations will be displayed in the list on the left of the page. 5. Add person. 1) Select an organization from the list on the left. 2) Click Add on right panel. 3) Set the person's basic information, including the person's name, gender, email, tel, effective period, and remark.
6) Click OK. 7) Face the enrollment station's camera and capture a picture according to the instructions on the enrollment station. 8) Click to capture again. 9) Click OK. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 6.2 Enroll Fingerprint via Client Software Before You Start • Download and install the client software on your computer before enrollment.
Note Up to 10 levels of organizations can be added. The added organizations will be displayed in the list on the left of the page. 5. Add person. 1) Select an organization from the list on the left. 2) Click Add on right panel. 3) Set the person's basic information, including the person's name, gender, email, tel, effective period, and remark.
10. Confirm to add the person. -Click Add to add the person and close the Add Person window. -Click Add and New to add the person and continue to add other persons. 6.3 Enroll Card via Client Software Before You Start • Download and install the client software on your computer before enrollment. • Power on and activate the device. For details about the activation, see Activation. Follow the steps below to enroll face. Figure 6-8 Flow Diagram of Enrolling Card Steps 1. Connect the device to the network. 2.
Figure 6-10 Add Person Note Once the person information is expired, the credentials and access control settings of the person will be invalid and the person will have no authorization to access the doors. 6. On the Add window, click Credential → Card . 7. Add the card No. 1) Click + → Settings . 2) Set the mode as Remote and select the card enrollment station from the drop-down list. 3) Set the enrollment station's IP address, port No., user name and password. 4) Set the RF card type.
-Click Add and New to add the person and continue to add other persons. 6.4 Get Person Information from Enrollment Station You can get the person information from the device for further operations. Steps Note • If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. • The gender of the persons will be Male by default.
The edited basic information will be imported to the client software. What to do next After the basic information is imported to the client software, you should enroll other information such as the face, fingerprint, etc. For details, see Enroll via Client Software. 7 Basic Operation 7.1 Login by Administrator Login the device backend to set the device basic parameters. If an administrator is added to the device, you can login by verifying the administrator's permission.
Figure 7-3 Administrator Page 3. Set the administrator's parameters. - Edit the super administrator's parameters: Tap admin and edit the super administrator's face and password. - Add a new administrator: Tap and set the administrator's type, add face and password. Figure 7-4 Administrator Information Page Super Administrator Contains all management and operation permissions. Normal Administrator Supports enrollment management and communication management.
Figure 7-5 Set Wired Network Set the device IP address, subnet mask, and gateway. Set Wireless Network Parameters The device can connect to the Ethernet via wireless connection. Long tap on the initial page for 3 s and login the home page. Tap Comm. → Wi-Fi . Figure 7-6 Wi-Fi Page After enabling WLAN, you should select a Wi-Fi for connection. Select a Wi-Fi and enable DHCP and enter the Wi-Fi's password to connect. Tap to connect the Wi-Fi.
Note Only parts of the device models support fingerprint recognition function. Refer to the actual page for details. Search Enter a person's employee ID and tap the search icon, or present a card on the card presenting area. The system will enter the User Information page. 7.5 Basic Settings 7.5.1 Set Time You can set the device time format and the current time. Long tap on the initial page for 3 s and login the device home page. Tap Basic → Time .
Figure 7-10 Enrollment Rules Page The configurable rules and descriptions are as follows: Verify by Administrator If enabling the function, you should verify the administrator's permission before enrollment. Employee ID Length Set the employee ID's length when enrolling a person's information. Employee ID Required You must enroll the employee ID when enrolling a person's information. Name Required You must enroll the person's name when enrolling a person's information.
Figure 7-11 Basic Settings Page White Light Brightness Set the supplement white light's brightness. The brightness range is from 1 to 100. 0 refers to turning off the light. 1 refers to the darkest, and 100 refers to the brightest. IR Light Brightness Set the IR light brightness when the IR light is enabled. The brightness range is from 1 to 100. 0 refers to turning off the light. 1 refers to the darkest, and 100 refers to the brightest.
Parameter Description Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Liveness Security Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Pitch Angle The maximum pitch angle when starting face authentication. By default, the angle is 30°.
Figure 7-13 Data Management Page 3. Tap Export Template. The template will be exported to the USB flash drive. 4. Edit the exported table and enroll the user information. Note Make sure the edited file is saved in the folder named "DSK1F600" in the root directory of the USB flash drive. 5. Tap Import User. Note Up to 2000 users can be imported. Result The system will read the user information in the USB flash drive automatically and import the data to the device. 7.6.
Long tap on the initial page for 3 s and login the home page. Tap Data. Figure 7-15 Data Management Page Tap Clear Enrolled Data to delete all enrolled data in the device, including all face pictures, fingerprints, card, etc. 7.7 System Maintenance You can view the device system information and capacity. You can also restore the system to factory settings, default settings, and reboot the system. Long tap on the initial page for 3 s and login the home page. Tap Maint..
Plug the USB flash drive in the device USB interface. Tap Upgrade → OK , and the device will read the digicap.dav file in the USB flash drive to start upgrading. Reboot The device will reboot after the confirmation.
A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.
B. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center. Incorrect Scanning The figures of scanning fingerprint displayed below are incorrect: Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain.
C. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure C-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all commonly used serial ports commands for all Hikvision access control and video intercom devices.
