Face Recognition Terminal User Manual
Face Recognition Terminal User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Face Recognition Terminal User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles.
Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
Face Recognition Terminal User Manual • The device cover for indoor use shall be kept from rain and moisture. • Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K1T671M DS-K1T671MF DS-K1T671TMW DS-K1T671TMFW Use only power supplies listed in the user instructions: Model Manufacturer Standard C2000IC12.0-24P-DE MOSO Power Supply Technology Co., Ltd. CEE C2000IC12.0-24P-GB MOSO Power Supply Technology Co., Ltd. BS KPL-040F-VI Channel Well Technology Co Ltd.
Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features ................................................................................................................................. 1 Chapter 2 Appearance ................
Face Recognition Terminal User Manual 7.2.1 Set Wired Network Parameters .................................................................................. 33 7.2.2 Set Wi-Fi Parameters ................................................................................................... 33 7.2.3 Set RS-485 Parameters ................................................................................................ 35 7.2.4 Set Wiegand Parameters ..................................................................
Face Recognition Terminal User Manual 7.11 Video Intercom .................................................................................................................. 58 7.11.1 Call Client Software from Device ............................................................................... 58 7.11.2 Call Center from Device ............................................................................................ 58 7.11.3 Call Device from Client Software ..............................................
Face Recognition Terminal User Manual 8.5.17 Time and Attendance Settings .................................................................................. 77 8.5.18 Set Video Intercom Parameters ................................................................................ 80 8.5.19 Access Control Settings ............................................................................................. 81 8.5.20 Set Biometric Parameters .......................................................................
Face Recognition Terminal User Manual 9.4.13 Import and Export Person Identify Information ...................................................... 116 9.4.14 Import Person Information ..................................................................................... 116 9.4.15 Import Person Pictures ........................................................................................... 117 9.4.16 Export Person Information ................................................................................
Face Recognition Terminal User Manual 9.9 Door Control ...................................................................................................................... 150 9.9.1 Control Door Status ................................................................................................... 150 9.9.2 Check Real-Time Access Records .............................................................................. 151 9.10 Event Center ..................................................................
Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command .....................................................
Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features Features of Normal Series • • • • • • • 7-inch LCD touch screen 2 MP wide-angle dual-lens Adjusts supplement light brightness manually Face recognition distance: 0.
Face Recognition Terminal User Manual Features of Advanced Series • • • • • • • 7-inch LCD touch screen 2 MP wide-angle dual-lens Adjusts supplement light brightness manually Face recognition distance: 0.3 m to 3 m Suggested height for face recognition: between 1.4 m and 1.9 m Deep learning algorithm 20,000 face capacity, 5,000 fingerprint capacity, and 100,000 event capacity Note Parts of the models support fingerprint module, refer to the actual products.
Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No. 1 Name Description Fingerprint Module For fingerprint recognition. Note Parts of models support fingerprint recognition function. 2 Card Swiping Area Swipe card within this area. 3 Display Screen 7-inch LCD touch screen.
Face Recognition Terminal User Manual No. Name Description 8 IR Light Supplement light for IR camera. 9 USB Interface Connect to USB flash drive. 10 TAMPER Tamper button. 11 Network Interface Connect to Ethernet. 12 SIM Card Slot Reserved 13 Debugging Port The debug terminal is used for debugging only. 14 Power Interface Connect to power supply.
Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment • Avoid backlight, direct sunlight, and indirect sunlight. • For better recognition, there should be light source in or near the installation environment. Note For details about installation environment, see Tips for Installation Environment. 3.2 Install with Gang Box Steps 1. According to the datum line on the mounting template, stick the mounting template on the wall or other surface, 1.
Face Recognition Terminal User Manual 2. Drill holes on the wall or other surface according to the mounting template and install the gang box. 3. Use two supplied screws (4_KA4 × 22-SUS) to secure the mounting plate on the gang box. 4. Use another four supplied screws to secure the mounting plate on the wall. Figure 3-2 Install Mounting Plate 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals. 6.
Face Recognition Terminal User Manual Figure 3-4 Insert Fingerprint Module 10. Align the device with the mounting plate and hang the device on the mounting plate.
Face Recognition Terminal User Manual 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device and the mounting plate. Figure 3-6 Secure Device Note • The installation height here is the recommended height. You can change it according to your actual needs. • For easy installation, drill holes on mounting surface according to the supplied mounting template. 3.3 Install without Gang Box Steps 1.
Face Recognition Terminal User Manual Figure 3-7 Mounting Template 2. Drill 6 holes on the wall or other surface according to Hole 1 and Hole 2 in the mounting template. 3. Insert the screw sockets of the setscrews in the drilled holes. Figure 3-8 Insert Screw Socket 4. Align the 6 holes to the mounting plate with the drilled holes.
Face Recognition Terminal User Manual Figure 3-9 Install Mounting Plate 5. Remove the two screws on the rear panel and remove the sheet to display the wiring terminals. 6. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 7. Install the sheet back to the device with the two screws. 8. Apply Silicone sealant among the cable wiring area to keep the raindrop from entering.
Face Recognition Terminal User Manual Figure 3-10 Apply Silicone Sealant 9. Insert the fingerprint module to the holes at the bottom of the main part. Figure 3-11 Install Fingerprint Module 10. Align the device with the mounting plate and hang the device on the mounting plate.
Face Recognition Terminal User Manual Figure 3-12 Install Device 11. Use two supplied screws (SC-M4 × 12TP10-SUS) to secure the device and the mounting plate.
Face Recognition Terminal User Manual Figure 3-13 Secure Device Note • The installation height here is the recommended height. You can change it according to your actual needs. • For easy installation, drill holes on mounting surface according to the supplied mounting template.
Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC and COM terminal with the door lock, connect the SENSOR terminal with the door contact, the BTN/GND terminal with the exit button, connect the alarm output and input terminal with the alarm output/ input devices, and connect the Wiegand terminal with the Wiegand card reader or the access controller.
Face Recognition Terminal User Manual Figure 4-1 Terminal Diagram The descriptions of the terminals are as follows: Table 4-1 Terminal Descriptions Group Group A No.
Face Recognition Terminal User Manual Group No.
Face Recognition Terminal User Manual Figure 4-2 Device Wiring • • • • • Note You should set the face recognition terminal's Wiegand direction to "Input" to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction to "Output" to transmit authentication information to the access controller. For details about Wiegand direction settings, see Setting Wiegand Parameters in Communication Settings. The suggested external power supply for door lock is 12 V, 1 A.
Face Recognition Terminal User Manual Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A.
Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 5.
Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Face Recognition Terminal User Manual • After activation, if you need to operate the device remotely via APP, you should scan the QR code to link to the APP. For details, see . • After activation, if you need to add administrator to manage the device parameters, you should set administrator. For details, see Add Administrator . 5.2 Activate via Web Browser You can activate the device via the web browser. Steps 1. Enter the device default IP address (192.0.0.
Face Recognition Terminal User Manual Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4.
Face Recognition Terminal User Manual 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6. Create a password in the password field, and confirm the password. Caution The password strength of the device can be automatically checked.
Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically.
Face Recognition Terminal User Manual 6.2 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-2 Welcome Page 2. Tap OK to save. Note • You can also change the settings in System Settings. • If you install the device indoors near the window or the face recognition function is not working well, select Others.
Face Recognition Terminal User Manual • If you do not configure the application mode and tap Next, the system will select Indoor by default. • If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.3 Set Administrator After device activation, you can add an administrator to manage the device parameters. Before You Start Activate the device and select an application mode. Steps 1. Optional: Tap Skip to skip adding administrator if required.
Face Recognition Terminal User Manual Figure 6-3 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. 4. Click OK. You will enter the authentication page.
Face Recognition Terminal User Manual Device is armed/not armed. / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . Scan QR code to authenticate. Note The QR code can be obtained from the visitor terminal. • Enter the device room No.
Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap 4. Optional: Tap and you can enter the device activation password for login. and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1.
Face Recognition Terminal User Manual 2. Tap the Password field and enter the device activation password. 3. Tap OK to enter the home page. Note The device will be locked for 30 minutes after 5 failed password attempts. Figure 7-3 Home Page 7.2 Communication Settings You can set the network parameters, the Wi-Fi parameter, the RS-485 parameters, and the Wiegand parameters on the communication settings page.
Face Recognition Terminal User Manual 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wired Network. Figure 7-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway.
Face Recognition Terminal User Manual Steps Note The function should be supported by the device. 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap. Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK.
Face Recognition Terminal User Manual - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. 7. Tap to save the network parameters. 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external access controller, secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2.
Face Recognition Terminal User Manual 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. • Output: A face recognition terminal can connect an external access controller.
Face Recognition Terminal User Manual 7.3 User Management On the user management interface, you can add, edit, delete and search the user. 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID. Note • The employee ID should be less than 32 characters.
Face Recognition Terminal User Manual Note • Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. • Up to 32 characters are allowed in the user name. 5. Optional: Add a face picture, fingerprints, or cards for the administrator. Note • For details about adding a face picture, see Add Face Picture . • Note For details about adding a fingerprint, see Add Fingerprint . • For details about adding a card, see Add Card . 6.
Face Recognition Terminal User Manual Note • Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. • The suggested user name should be within 32 characters. 5. Tap the Face Picture field to enter the face picture adding page. Figure 7-8 Add Face Picture 6. Look at the camera. Note • Make sure your face picture is in the face picture outline when adding the face picture. • Make sure the captured face picture is in good quality and is accurate.
Face Recognition Terminal User Manual After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page. 7. Tap Save to save the face picture. 8. Optional: Tap Try Again and adjust your face position to add the face picture again. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission.
Face Recognition Terminal User Manual Note • The same fingerprint cannot be repeatedly added. • Up to 10 fingerprints can be added for one user. • You can also use the client software or the fingerprint recorder to record fingerprints. For details about the instructions of scanning fingerprints, see Tips for Scanning Fingerprint . 7. Set the user role. Administrator The user is the administrator.
Face Recognition Terminal User Manual Note • The card No. cannot be empty. • Up to 20 characters are allowed in the card No. • The card No. cannot be duplicated. 8. Configure the card type. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10.
Face Recognition Terminal User Manual Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 7. Tap to save the settings. 7.3.
Face Recognition Terminal User Manual Note The employee ID cannot be edited. 7.4 Data Management You can delete data, import data, and export data. 7.4.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data or Face Data. 4. Enter the created password when you exported the data.
Face Recognition Terminal User Manual 7.4.3 Export Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Export Data . 3. Tap Event Data, User Data, or Face Data. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password. Note • The supported USB flash drive format is DB. • The system supports the USB flash drive with the storage of 1G to 32G. Make sure the free space of the USB flash drive is more than 512M.
Face Recognition Terminal User Manual Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. QR Code Put the QR code in front of the device camera to authenticate via QR code. Note Authentication via QR code should be supported by the device. Password Enter the password to authenticate via password. If authentication completed, a prompt "Authenticated" will pop up. 7.5.
Face Recognition Terminal User Manual Long tap on the initial page for 3 s and slide to the left/right by following the gesture and login the device home page. Tap Basic. Figure 7-9 Basic Settings Page shortcut key, voice, time, language, supplement light, community No., building No., and Unit No. Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function.
Face Recognition Terminal User Manual When you tap the call button on the authentication page, you can call the center directly. Call Specified Room No. You should set a room No. When you tap the call button on the authentication page, you can call the configured room directly without dialing. Voice Settings You can enable/disable the voice prompt function and adjust the voice volume. Note You can set the voice volume between 0 and 10. Time Settings Set the time zone, the device time and the DST.
Face Recognition Terminal User Manual 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance. The configurable parameters includes application mode, face liveness level, face recognition distance, face recognition interval, wide dynamic, face 1:N security level, face 1:1 security level, ECO settings, hard hat detection level, and face with mask detection. Long tap on the initial page for 3 s and login the home page. Tap Biometric.
Face Recognition Terminal User Manual Parameter Description ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode.
Face Recognition Terminal User Manual Figure 7-11 Access Control Parameters The available parameters descriptions are as follows: Table 7-2 Access Control Parameters Descriptions Parameter Description Terminal Auth. Mode (Terminal Select the face recognition terminal's authentication mode. You Authentication Mode) can also customize the authentication mode. Note • Only the device with the fingerprint module supports the fingerprint related function.
Face Recognition Terminal User Manual Parameter Description Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Available door locked time range: 1 to 255s. Authentication Interval Set the device authenticating interval. Available authentication interval range: 0 to 65535. 7.9 Time and Attendance Status Settings Set time and attendance status.
Face Recognition Terminal User Manual 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Manual. Figure 7-13 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status.
Face Recognition Terminal User Manual 7.9.3 Set Auto Attendance via Device Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 7-14 Auto Attendance Mode 3.
Face Recognition Terminal User Manual Note The attendance status will be valid within the configured schedule. Result When you authenticate on the initial page, the authentication will be marked as the configured attendance status according to the configured schedule. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.9.
Face Recognition Terminal User Manual Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap OK. 5) Repeat step 1 to 4 according to your actual needs.
Face Recognition Terminal User Manual Figure 7-16 Maintenance Page System Information You can view the device model, serial No., versions, address, production data, QR code, and open source code license. Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of, user, face picture, card, event and fingerprint. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details.
Face Recognition Terminal User Manual All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect. Restore to Factory Settings All parameters will be restored to the factory settings. The system will reboot to take effect. Reboot Reboot the device. 7.
Face Recognition Terminal User Manual 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the main station and the device to the client software. Note For details about adding device, see Add Device. 5. Set the main station's IP address and SIP address in the remote configuration page. Note For details about the operation, see the user manual of the main station. 6. Call the center.
Face Recognition Terminal User Manual 7.11.4 Call Room from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the indoor station and the device to the client software. Note For details about adding device, see Add Device. 5.
Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:". Enter the device user name and the password.
Face Recognition Terminal User Manual Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view. 8.
Face Recognition Terminal User Manual Add Face Picture Click User → Add to enter the Add Person page. Click + on the right to upload a face picture from the local PC. Note The picture format should be JPG, JPEG or PNG. The size should be less than 200K. Click OK to save the settings. Set Permission Time Click User → Add to enter the Add Person page. Set Start Time and End Time. Click OK to save the settings. Set Access Control Click User → Add to enter the Add Person page.
Face Recognition Terminal User Manual Figure 8-2 Search Page Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 8.5 Configuration 8.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path. Set Live View Parameters Click Configuration → Local to enter the Local page.
Face Recognition Terminal User Manual You can also click Open to open the file folder to view details. Set Captured Pictures Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 8.5.2 View Device Information View the device name, language, model, serial No., QR code, version, device capacity, etc.
Face Recognition Terminal User Manual 8.5.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-4 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 8.5.5 View Open Source Software License Go to Configuration → System → System Settings → About Device , and click View Licenses to view the device license. 8.5.6 Upgrade and Maintenance Reboot device, restore device parameters, and upgrade device version.
Face Recognition Terminal User Manual Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information. Unlink APP Account Unlink the Hik-Connect account from the platform. Import and Export Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Export Click Export to export the logs or device parameters.
Face Recognition Terminal User Manual 8.5.8 Security Mode Settings Set the security mode for logging in the client software. On the Device for Management page, click Configuration → System → Security → Security Service . Select a security mode from the drop-down list, and click Save. Security Mode High security level for user information verification when logging in the client software. Compatible Mode The user information verification is compatible with the old client software version when logging in.
Face Recognition Terminal User Manual 8. Import the signed certificate. 1) Select a certificate type in the Import Passwords area, and select a certificate from the local, and click Install. 2) Select a certificate type in the Import Communication Certificate area, and select a certificate from the local, and click Install. Install Other Authorized Certificate If you already has an authorized certificate (not created by the device), you can import it to the device directly. Steps 1.
Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Face Recognition Terminal User Manual DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, and the IPv4 default gateway automatically. NIC Type Select a NIC type from the drop-down list. By default, it is Auto. DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need.
Face Recognition Terminal User Manual Figure 8-7 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's name, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click TCP/IP Settings. 2) Set the IP address, subnet mask, and default gateway.
Face Recognition Terminal User Manual Steps 1. Click Configuration → Network → Advanced → Platform Access to enter the settings page. 2. Check the checkbox of Enable to enable the function. 3. Select the Platform Access Mode. Note Hik-Connect is an application for mobile devices. With the App, you can view live image of the device, receive alarm notification and so on. 4. Create a Stream Encryption/Encryption Key for the device. Note 6 to 12 letters (a to z, A to Z) or numbers (0 to 9), case sensitive.
Face Recognition Terminal User Manual Note The function should be supported by the device. Steps 1. Click Configuration → Network → Advanced → HTTP Listening . 2. Edit the destination IP or host name, URL and port. 3. Optional: Click Test to test whether the entered IP address or host name are valid. 4. Optional: Click Default to reset the destination IP or host name. 5. Click Save. 8.5.13 Set Video and Audio Parameters Set the image quality, resolution, and the device volume.
Face Recognition Terminal User Manual 8.5.14 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1. Click Configuration → Video/Audio → Audio Prompt . Figure 8-9 Customize Audio Content 2. set the appellation. 3. Enable the function. 4. Set the time duration when authentication succeeded. 1) Click Add. 2) Set the time duration and the language.
Face Recognition Terminal User Manual Note If authentication is failed in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 6. Click Save to save the settings. 8.5.15 Set Image Parameters Set the video standard, WDR, brightness, contrast, saturation, and sharpness. Steps 1. Click Configuration → Image Adjustment . Figure 8-10 Image Settings Page 2.
Face Recognition Terminal User Manual When there are both very bright and very dark areas simultaneously in the view, WDR balances the brightness level of the whole image and provide clear images with details. Brightness/Contrast/Saturation/Sharpness Drag the block or enter the value to adjust the live video's brightness, contrast, saturation, and sharpness. Start/end recording video. Capture the image. 3. Click Default to restore the parameters to the default settings. 8.5.
Face Recognition Terminal User Manual Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Disable. Result You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. Time Settings Steps 1. Click Configuration → Time Settings to enter the settings page. 2. Select Status Type. 3. Optional: Edit Schedule Name according to the actual needs. 4.
Face Recognition Terminal User Manual Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. Set Auto Attendance via Web Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1.
Face Recognition Terminal User Manual Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule. If you tap the edit icon on the result tab, you can select a status to take attendance manually, the authentication will be marked as the edited attendance status. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 8.5.
Face Recognition Terminal User Manual Unit No. Set the device installed unit No. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Community No. Set the device installed community No. If set the device type as Outer Door Station, you can set the period No., outer door station No., and community No. Period No. Set the device installed period No. Outer Door Station No.
Face Recognition Terminal User Manual Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters. If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list.
Face Recognition Terminal User Manual Recognition Interval If the interval between card presenting of the same card is less than the configured value, the card presenting is invalid. Authentication Interval You can set the authentication interval of the same person when authenticating. The same person can only authenticate once in the configured interval. A second authentication will be failed. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value.
Face Recognition Terminal User Manual Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed.
Face Recognition Terminal User Manual In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption Sector M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13.
Face Recognition Terminal User Manual Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, Access Controller, or Disable. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2.
Face Recognition Terminal User Manual Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. Set Privacy Parameters Set the event storage type, picture upload and storage parameters, and the picture clearing parameters. Go to Configuration → Access Control → Privacy Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting.
Face Recognition Terminal User Manual Clear All Pictures in Device Note All pictures cannot be restored once they are deleted. Clear Registered Face Pictures All registered pictures in the device will be deleted. Clear Captured Pictures All captured pictures in the device will be deleted. Set Card Authentication Parameters Set the card reading content when authenticate via card on the device. Go to Configuration → Access Control → Card Authentication Settings .
Face Recognition Terminal User Manual Figure 8-15 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
Face Recognition Terminal User Manual Application Mode Select either others or indoor according to actual environment. Face Recognition Mode Normal Mode Recognize face via the camera normally. Deep Mode The device can recognize a much wider people range than the normal mode. This mode is applicable to a more complicated environment. Continuous Face Recognition Interval Set the time interval between two continuous face recognitions when authenticating.
Face Recognition Terminal User Manual After enabling the hard hat detection, you can set the strategy. None The function is disabled. The device will not detect whether a person is wearing a hard hat or not. Reminder of Wearing Hard Hat If the person do not wear the hard hat when authenticating, the device will pop up a prompt and the door will open. Must Wear Hard Hat If the person do not wear the hard hat when authenticating, the device will pop up a prompt and the door will keep closed.
Face Recognition Terminal User Manual Figure 8-16 Notice Page Sleep Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time. Theme Management You can click + in the frame and upload the screen saver pictures from the local PC. Note By now, there is only one theme can be added. Play Schedule After you have created a theme, you can select the theme and draw a schedule on the time line. Select the drawn schedule and you can edit the exact start and end time.
Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
Face Recognition Terminal User Manual 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices.
Face Recognition Terminal User Manual Figure 9-3 Add Single Online Device Figure 9-4 Add Multiple Online Devices 4. Enter the required information. Name Enter a descriptive name for the device. IP Address Enter the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port You can customize the port number. The port number of the device is obtained automatically in this adding mode.
Face Recognition Terminal User Manual By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Face Recognition Terminal User Manual 2. Click Device tab on the top of the right panel. 3. Click Online Device to show the online device area at the bottom of the page. The searched online devices are displayed in the list. 4. Select multiple devices. Note For the inactive device, you need to create the password for it before you can add the device properly. For details, refer to . 5. Click Add to open the device adding window. 6. Enter the required information.
Face Recognition Terminal User Manual 2. Click Device tab on the top of the right panel. The added devices are displayed on the right panel. 3. Click Add to open the Add window, and then select IP/Domain as the adding mode. 4. Enter the required information. Name Create a descriptive name for the device. For example, you can use a nickname that can show the location or feature of the device. Address The IP address or domain name of the device. Port The devices to add share the same port number.
Face Recognition Terminal User Manual Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Finish adding the device. - Click Add to add the device and back to the device list page. - Click Add and New to save the settings and continue to add other device. Add Devices by IP Segment If the devices share the same port No.
Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 6. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS (Transport Layer Security) protocol for security purpose . Note • This function should be supported by the device.
Face Recognition Terminal User Manual Note This function should be supported by the device. 5. Optional: Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 6. Optional: Check Import to Group to create a group by the device name, and import all the channels of the device to the group. 7. Finish adding the device. - Click Add to add the device and go back to the device list.
Face Recognition Terminal User Manual Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
Face Recognition Terminal User Manual - Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support. Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked.
Face Recognition Terminal User Manual Note The resources (such as alarm inputs/outputs, access points, etc.) of this device will be imported to the group by default. 9.3.2 Import Resources to Group You can import the device resources (such as alarm inputs/outputs, access points, etc.) to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3.
Face Recognition Terminal User Manual 9.3.4 Remove Resources from Group You can remove the added resources from the group. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 9.
Face Recognition Terminal User Manual Show Persons in Sub Organization Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations. 9.4.2 Configure Basic Information You can add person to the client one by one and configure the person's basic information such as name, gender, email, phone number, etc. Steps 1. Enter Person module.
Face Recognition Terminal User Manual - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 9.4.3 Issue a Card by Local Mode If a card enrollment station is available, you can issue a card by local mode. To read the card number, you should connect the card enrollment station to the PC running the client by USB interface or COM, and place the card on the card enrollment station. Steps 1. Enter Person module. 2.
Face Recognition Terminal User Manual Figure 9-6 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
Face Recognition Terminal User Manual This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add. The card will be issued to the person. 9.4.
Face Recognition Terminal User Manual Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first. For details, refer to Configure Basic Information . 3. Click Add Face in the Basic Information area. 4. Select Take Photo to enter Take Photo window. 5.
Face Recognition Terminal User Manual 9.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3.
Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Credential → Fingerprint panel, click +. 4. In the pop-up window, select the collection mode as Local. 5. Select the model of the connected fingerprint recorder.
Face Recognition Terminal User Manual 4. In the pop-up window, select the collection mode as Remote. 5. Select an added access control device or the enrollment station from the drop-down list. Note If you select the enrollment station, you should click Login, and set IP address, port No., user name and password of the device. 6. Collect the fingerprint. 1) Click Start. 2) Place and lift your fingerprint on the fingerprint scanner of the selected access control device to collect the fingerprint.
Face Recognition Terminal User Manual Note Persons' PIN codes cannot be repeated. - Click Generate to randomly generate an unrepeated PIN code of 6 digits. Note If there are repeated PIN codes, a prompt will pop up on the client. The admin can generate a new PIN code to replace the repeated PIN code and notify related persons. 5. Check the person's operation permissions.
Face Recognition Terminal User Manual 9.4.10 Customize Person Information You can customize the person properties which are not pre-defined in the client according to actual needs, e.g., place of birth. After customizing, when add a person, you can enter the custom information to make the person information complete. Steps 1. Enter Person module. 2. Set the fields of custom information. 1) Click Custom Property. 2) Click Add to add a new property. 3) Enter the property name. 4) Click OK. 3.
Face Recognition Terminal User Manual 5. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 9.4.12 Configure Additional Information When adding person, you can configure the additional information for the person, such as person's identity type, identity No., country, etc., according to actual needs. Steps 1. Enter Person module. 2.
Face Recognition Terminal User Manual Note • If the person has multiple cards, separate the card No. with semicolon. • Items with asterisk are required. • By default, the Hire Date is the current date. to select the CSV/Excel file with person information from local PC. 7. Click 8. Click Import to start importing. Note • If a person No. already exists in the client's database, delete the existing information before importing. • You can import information of no more than 2,000 persons. 9.4.
Face Recognition Terminal User Manual 9.4.16 Export Person Information You can export the added persons' information to local PC as a CSV/Excel file. Before You Start Make sure you have added persons to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' information will be exported if you do not select any organization. 3. 4. 5. 6. Click Export to open the Export panel. Check Person Information as the content to export.
Face Recognition Terminal User Manual Before You Start Make sure you have saved the structure data. Steps 1. Enter the Person module. 2. Optional: Select a person item in the list. 3. Click Delete Registered Picture to delete the registered picture. 9.4.
Face Recognition Terminal User Manual Before You Start • Make sure you have added at least two organizations. • Make sure you have imported person information. Steps 1. Enter Person module. 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5. Select the organization to move persons to. 6. Click OK. 9.4.
Face Recognition Terminal User Manual After reporting card loss, the access authorization of this card will be invalid and inactive. Other person who gets this card cannot access the doors by swiping this lost card. 4. Optional: If the lost card is found, you can click to cancel the loss. After cancelling card loss, the access authorization of the person will be valid and active. 5.
Face Recognition Terminal User Manual M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E. If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should enable this function and select the sector of the card to encrypt. Remote Mode: Issue Card by Card Reader Select an access control device added in the client and swipe the card on its card reader to read the card number. 9.
Face Recognition Terminal User Manual Note Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
Face Recognition Terminal User Manual Note Up to 8 time duration(s) can be set for each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
Face Recognition Terminal User Manual 2. Click Add to open the Add window. 3. In the Name text field, create a name for the access group as you want. 4. Select a template for the access group. Note You should configure the template before access group settings. Refer to Configure Schedule and Template for details. 5. In the left list of the Select Person field, select person(s) to assign access authority. 6.
Face Recognition Terminal User Manual 4) View the applying status in the Status column or click Applying Status to view all the applied access group(s). Note You can check Display Failure Only to filter the applying results. The selected persons in the applied access groups will have the authorization to enter/exit the selected doors/door stations with their linked card(s) or fingerprints. 9. Optional: Click to edit the access group if necessary.
Face Recognition Terminal User Manual 9.7.1 Configure Device Parameters After adding the access control device, you can configure the parameters of access control device, access control points. Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
Face Recognition Terminal User Manual If enable the function, the device can recognize the NFC card. You can present NFC card on the device. Enable M1 Card If enable the function, the device can recognize the M1 card. You can present M1 card on the device. Enable EM Card If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4.
Face Recognition Terminal User Manual Open Duration After swiping the normal card and relay action, the timer for locking the door starts working. Super Password The specific person can open the door by inputting the super password. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Click Advanced to configure more parameters.
Face Recognition Terminal User Manual Note • The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. • Some of the following parameters are not listed in the Basic Information page, click Advanced to edit the parameters. Basic Information Name Edit the card reader name as desired.
Face Recognition Terminal User Manual Select the fingerprint recognition level in the drop-down list. Face 1:N Matching Threshold Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate when authentication. Face Recognition Interval The time interval between two continuous face recognitions when authenticating. Face Anti-Spoofing Enable or disable the live face detection function.
Face Recognition Terminal User Manual 2. In the device list on the left, click to expand the door, select an alarm input and you can edit the alarm input's parameters on the right. 3. Set the alarm output parameters. Name Edit the card reader name as desired. Alarm Output Active Time How long the alarm output will last after triggered. 4. Click OK. 5. Optional: Set the switch on the upper right corner to ON to trigger the alarm output. 9.7.
Face Recognition Terminal User Manual Delete Selected Select one duration on the time bar, click Delete Selected to delete this duration. Clear Click Clear to clear all the duration settings in the week schedule. 4. To set the door status during the holiday, click the Holiday and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Click Add. 3) Enter the start date and end date.
Face Recognition Terminal User Manual 2) Create a name for the group as desired. 3) Specify the start time and end time of the effective period for the person/card group. 4) Select members(s) and card(s) in the Available list, and the selected member(s) and card(s) will be added to the Selected list. Note Make sure you have issue card to the person. Make sure you have set access group and apply the access group to the access control device successfully. 5) Click Save.
Face Recognition Terminal User Manual Note You can check Offline Authentication to enable the super password authentication when the access control device is disconnected with the client. Local Authentication and Super Password Authentication by the access control device and by the super password. 4) Select the added person/card group in the left list below and it will be added to the Selected list on the right as the authentication group.
Face Recognition Terminal User Manual Figure 9-13 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4.
Face Recognition Terminal User Manual Figure 9-14 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 9.7.5 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
Face Recognition Terminal User Manual Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Note You can authenticate by the first person again to disable the first person mode. 4. Click Add on the First Person List panel. 5.
Face Recognition Terminal User Manual Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect. Example Set Card Swiping Path: If you select Reader In_01 as the beginning, and select Reader In_02, Reader Out_04 as the linked card readers.
Face Recognition Terminal User Manual Set Network Parameters After adding the access control device, you can set the device log uploading mode, and create ISUP account via wired network. Set Log Uploading Mode You can set the mode for the device to upload logs via ISUP protocol. Steps 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and enter Network → Uploading Mode . 4.
Face Recognition Terminal User Manual Note If set the ISUP version as 5.0, you should create an ISUP key for the ISUP account. 9. Set an account name for the network center. 10. Click Save. Set Device Capture Parameters You can configure the capture parameters of the access control device, including manual capture and event triggered capture. Note • The capture function should be supported by the device.
Face Recognition Terminal User Manual Set Manual Capture Parameters In Status Monitoring module, you can capture a picture manually the access control device's camera by clicking a button. Before that, you need to set the parameters for the capture such as picture quality. Before You Start Before setting the capture parameters, you should set the saving path first to define where the captured pictures are saved. For details, refer to Set Picture Storage in the user manual of the client software.
Face Recognition Terminal User Manual If enabled, the captured face picture when authenticating will be saved on the device. ECO Mode After enabling the ECO mode, the device can authenticate faces in the low light or dark environment. And you can set he ECO mode threshold, ECO mode (1:N), and ECO mode (1:1). ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
Face Recognition Terminal User Manual Note • The sector ID ranges from 1 to 100. • By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. Set RS-485 Parameters You can set the access control device's RS-485 parameters including the baud rate, data bit, the stop bit, parity type, flow control type, communication mode, work mode, and connection mode. Steps Note The RS-485 Settings should be supported by the device. 1. Enter the Access Control module.
Face Recognition Terminal User Manual 5. Select the Wiegand channel No. and the communication mode from the drop-down list. Note If you set Communication Direction as Sending, you are required to set the Wiegand Mode as Wiegand 26 or Wiegand 34. 6. Check Enable Wiegand to enable the Wiegand function. 7. Click Save. • The configured parameters will be applied to the device automatically. • After changing the communication direction, the device will reboot automatically. 9.
Face Recognition Terminal User Manual 4. Set the linkage actions of the event. 1) Select the event(s) and click Edit Linkage to set the client actions when the events triggered. Audible Warning The client software gives an audible warning when alarm is triggered. You can select the alarm sound for audible warning. Note For setting the alarm sound, please refer to Set Alarm Sound in the user manual of client software.. Send Email Send an email notification of the alarm information to one or more receivers.
Face Recognition Terminal User Manual An event-related picture will be captured when the selected event happens. Note The device should support recording. Buzzer on Reader The audible warning of card reader will be triggered. Alarm Output The alarm output will be triggered for notification when the selected event happens Alarm Input Arm or disarm the alarm input. Note The device should support alarm input function. Access Point The door status of open, close, remain open, or remain close will be triggered.
Face Recognition Terminal User Manual 1. 2. 3. 4. 5. 6. 7. Click Access Control → Linkage Configuration . Select the access control device from the list on the left. Click Add to add a new linkage. Select Card Linkage as the event source. Enter the card number or select the card from the drop-down list. Select the card reader where the card swipes. In the Linkage Target area, set the property target to enable this action. Buzzer on Controller The audible warning of access control device will be triggered.
Face Recognition Terminal User Manual Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 9.8.4 Configure Device Actions for Person ID You can set the access control device's linkage actions for the specified person ID.
Face Recognition Terminal User Manual Access Point The door status of open, close, remain open, or remain closed will be triggered. Audio Play The audio prompt will be triggered. And the select audio index related audio content will be played according to the configured play mode. 8. Click Save. 9. Optional: After adding the device linkage, you can do one or more of the followings: Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it.
Face Recognition Terminal User Manual Open Door When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Close Door When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials. Remain Open The door will be unlocked (no matter closed or open). All the persons can access the door with no credentials required.
Face Recognition Terminal User Manual 4. Optional: Click the event to view the accessed person details, including person pictures (captured picture and profile), person No., person name, organization, phone, contact address, etc. Note You can double click the captured picture to enlarge it to view the details. 5. Optional: Right click on the column name of the access event table to show or hide the column according to actual needs. 9.
Face Recognition Terminal User Manual Figure 9-15 Arm Device After turned on, the device(s) will be armed. And notifications about the events triggered by the armed device(s) will be automatically sent to the client software in real-time. 9.10.2 View Real-Time Events The real-time event information received by the client of the connected resources are displayed. You can check the real-time event information, including event source, event time, priority, etc.
Face Recognition Terminal User Manual 3. Optional: Right-click the table header of the event list to customize the event related items to be displayed in the event list. 4. Select an event in the event list to view the event details. 5. Optional: Perform the following operations if necessary. Handle Single Event Click Handle to enter the processing suggestion, and then click OK. Note After an event is handled, the Handle button will become Add Remark.
Face Recognition Terminal User Manual 9.10.3 Search Historical Events You can search and view historical events by setting search conditions such as time, device type, and priority in the client. For the searched events, you can handle and export them. Before You Start Enable receiving events from devices before the client can receive event information from the device,see Enable Receiving Event from Devices for details. Steps 1. Click Event Center → Event Search to enter the event search page. 2.
Face Recognition Terminal User Manual Enter a key word (supports fuzzy search) to quickly search the target historical event(s). For example, you can enter a person's name to search the events related with this person. 3. Click Search to search the events according the conditions you set. Figure 9-16 Search Historical Events Note If you have selected Access Control as device type in Step 2, you can view extra information such as card No.
Face Recognition Terminal User Manual 5. Select an event in the event list to view the event details. 6. Optional: Perform one of the following operations. Handle Single Event Handle single event: Select one event that needs to be handled, and then click Handle in the event information details page, and enter the handling suggestion. Note After an event is handled, the Handle button will become Add Remark, click Add Remark to add more remarks for this handled event.
Face Recognition Terminal User Manual 9.11 Time and Attendance The Time and Attendance module provides multiple functionalities to track and monitor when employees start and stop work, and full control of employees working hours such as late arrivals, early departures, time taken on breaks and absenteeism. Note In this section, we introduce the configurations before you can getting the attendance reports. The access records recorded after these configurations will be calculated in the statistics. 9.11.
Face Recognition Terminal User Manual When you work for a certain period after end-work time on workday, you will reach different overtime level: overtime level 1, overtime level 2 and overtime level 3. You can set different work hour rate for three overtime levels, respectively. Work Hour Rate Work Hour Rate is used to calculate work hours by multiplying it by overtime. When you work for a certain period after end-work time on workday, you will reach different overtime level.
Face Recognition Terminal User Manual Attendance status will be calculated as Check in/out according to the actual attendance status on the device. 6. Click Set as Check Point. The configured attendance check point(s) are displayed on the right list. 7. Optional: After setting attendance check points, and perform the following operations. Edit Check Point Check one attendance check point, click Edit to edit its information including name, check point function, etc.
Face Recognition Terminal User Manual Add Irregular Holiday You can configure a holiday which will take effect annually on irregular days during the effective period, such as Bank Holiday. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Holiday to enter the Holiday Settings page. 3. Click Add to open the Add Holiday page. 4. Check Irregular Holiday as holiday type. 5. Custom a name for the holiday. 6. Set the start date of the holiday.
Face Recognition Terminal User Manual 5. Click Add on the right to add a minor leave type. 6. Optional: Perform one of the following operations for minor leave type. Edit Move the cursor over the minor leave type and click type. to edit the minor leave Delete Select one or multiple major leave types and click Delete on the right to delete the selected minor leave type(s).
Face Recognition Terminal User Manual Configure Break Time You can add break time and set start time, end time, duration, calculation mode and other parameters for the break. The added break time can also be edited or deleted. Steps 1. Click Time & Attendance → Timetable → Break Time . The added break time is displayed in the list. 2. Click Break Time Settings to enter Break Time Settings window. 3. Click Add. 4. Enter a name for the break time. 5. Set related parameters for the break time.
Face Recognition Terminal User Manual Set Enable T&A Status switch to on to calculate the actual break time according to attendance status on the device. Note This function should be supported by the device. Valid Authentication Interval During the valid authentication interval, person swiping card for several times will only be calculated as once when calculating attendance data. 6. Click Save to save the settings. 7. Optional: Click Add to continue adding break time.
Face Recognition Terminal User Manual Figure 9-18 Add Timetable 3. Create a name for the timetable. Note You can click the color icon beside the name to customize the color for the valid timetable on the time bar in the Configuration Result area. 4. Select the timetable type as general. 5. Select calculation method. First In & Last Out The first check-in time is recorded as start work time and the last check-out time is recorded as the end-work time.
Face Recognition Terminal User Manual Note This function should be supported by the device. 7. Optional: Enable Calculate Break Time into Attended Duration. Note When enabled, break time will be calculated into the overall attendance duration. That is, the actual attendance duration equals to the overall attendance duration (includes break time). 8. Set the related attendance time parameters as the following: Start/End-Work Time Set the start-work time and end-work-time.
Face Recognition Terminal User Manual 9.11.3 Add Shift You can add shift for employees including setting shift period (day, week, month) and the effective attendance time. According to the actual requirements, you can adding multiple timetables in one shift for employees, which requires them to check in and check out for each timetable. Before You Start Add a timetable first. See Add General Timetable for details. Steps 1. Click Time & Attendance → Shift to enter shift settings page. 2.
Face Recognition Terminal User Manual Figure 9-20 Add Multiple Timetables 6. Click Save. The added shift lists on the left panel of the page. At most 64 shifts can be added. 7. Optional: Assign the shift to organization or person for a quick shift schedule. 1) Click Assign. 2) Select Organization or Person tab and check the desired organization(s) or person(s) box. The selected organizations or persons will list on the right page. 3) Set the Expire Date for the shift schedule.
Face Recognition Terminal User Manual 9.11.4 Manage Shift Schedule Shift work is an employment practice designed to make use of all 24 hours of the clock each day of the week. The practice typically sees the day divided into shifts, set periods of time during which different shifts perform their duties. You can set department schedule, person schedule, and temporary schedule.
Face Recognition Terminal User Manual Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work. Scheduled on Holidays On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule. Effective for Overtime The persons' overtime will be recorded for this schedule.
Face Recognition Terminal User Manual 6. Set the start date and end date. 7. Set other parameters for the schedule. Check-in Not Required Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work. Scheduled on Holidays On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule.
Face Recognition Terminal User Manual It contains more than one timetables. The person can check in/out in any of the timetables and the attendance will be effective. If the multiple shift schedules contains three timetables: 00:00 to 07:00, 08:00 to 15:00 and 16:00 to 23:00. The attendance of the person adopting this multiple shift schedules will be effective in any of the three timetables. If the person checks in at 07:50, it will apply the nearest timetable 08:00 to 15:00 to the person's attendance.
Face Recognition Terminal User Manual 5. Select the correction type as Check-in, Check-out, Break-in, Break-out, etc,. and set the correct time. Note You can click to add multiple correction items. At most 8 check-in/out items can be added. 6. Optional: Enter the remark information as desired. 7. Click Save to save the above settings. 8. Optional: After adding the check-in/out correction, perform one of the following operations. View Click or mode.
Face Recognition Terminal User Manual 5. Select the major leave type and minor leave type from the drop-down list. Note You can set the leave type in Attendance Settings. For details, refer to Configure Leave Type . 6. 7. 8. 9. Set the time for leave. Optional: Enter the remark information as desired. Click Save. Optional: After adding the leave and business trip, perform one of the following operations. View Click or mode.
Face Recognition Terminal User Manual 3. In the Auto-Calculate Attendance area, set the time that you want the client to calculate the data. 4. Click Save. The client will calculate the attendance data of the previous day from the time you have configured. Manually Calculate Attendance Data You can manually calculate attendance data by setting conditions including attendance time, department, attendance status, etc. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Calculation .
Face Recognition Terminal User Manual 9.11.8 Attendance Statistics You can check the original attendance record, generate and export the attendance report based on the calculated attendance data. Get an Overview of Employees' Attendance Data You can search and view the employee's attendance data on the client, including attendance time, attendance status, check point, etc. Before You Start • You should add organizations and persons in Person module and the persons have swiped cards.
Face Recognition Terminal User Manual Check two or more incorrect records, click Edit Attendance Status on the upper left corner and select from the drop-down list to batch edit multiple pieces of attendance status. Generate Report Click Report to generate the attendance report. Export Report Click Export and select saving path to export the attendance report (CVS file) to the local PC. Custom Export Click Custom Report and set conditions to export attendance records according to actual needs.
Face Recognition Terminal User Manual Report Name Enter a name for the report. Report Type Select one report type and this report will be generated. Report Time The time to be selected may vary for different report type. Person Select the added person(s) whose attendance records will be generated for the report. Note You can view the selected person(s) in the right side of the Person area. 5. Set the schedule to send the report to the email address(es) automatically.
Face Recognition Terminal User Manual Generate Report Select one added report and click Report to generate the report instantly and you can view the report details. 9.12 System Configuration 9.12.1 Set General Parameters You can configure the frequently-used parameters, including log expired time, network performance, etc. Steps 1. Enter the System Configuration module. 2. Click General tab to enter the General Settings page. 3. Configure the general parameters.
Face Recognition Terminal User Manual Automatically synchronize the time of the added devices with the time of the PC running the client at a specified time point. Auto-Upgrade Device Set the upgrading mode after the new version of device are detected. Disable After enabled, the client will not download the firmware package and upgrade even if the client detects a new version of the client.
Face Recognition Terminal User Manual 9.12.3 Set Alarm Sound When the event is triggered, the client can give an audible warning to notify the security personnel. You can set the sound of the audible warning in this section. Steps 1. Open the System Configuration page. 2. Click Alarm Sound tab to enter the Alarm Sound Settings page. 3. Optional: Click and select the audio files from the local path for different events. 4. Optional: Add customized alarm sound. 1) Click Add to add customized alarm sound.
Face Recognition Terminal User Manual Max. Speaking Duration with Access Control Device Specify the seconds that the call with access control device will last for at most. The maximum speaking duration between access control device and the client can be set from 90s to 120s. 4. Click Save. 9.12.5 Set File Saving Path The pictures captured in Status Monitoring module are stored on the local PC. The saving path of these files can be set. Steps 1. Open the System Configuration page. 2.
Face Recognition Terminal User Manual Enter the user name of the sender email address if Server Authentication is checked. Password Enter the password of the sender Email address if Server Authentication is checked. Receiver 1 to 3 Enter the email address of the receiver. Up to 3 receivers can be set. 4. Optional: Click Send Test Email to send an email to the receiver for test. 5. Click Save. 9.
Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
Face Recognition Terminal User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc.
Face Recognition Terminal User Manual 187
Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
Face Recognition Terminal User Manual Appendix D.
Face Recognition Terminal User Manual Device without Fingerprint Module Figure D-2 Device without Fingerprint Module 190
Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD15654B-C
