DS-K1T680 Series Face Recognition Terminal User Manual
DS-K1T680 Series Face Recognition Terminal User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T680 Series Face Recognition Terminal User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T680 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T680 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T680 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T680 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T680 Series Face Recognition Terminal User Manual • Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions. • Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T680 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K1T680D-E1 DS-K1T680D DS-K1T680DW DS-K1T680DG DS-K1T680DG1 DS-K1T680DF-E1 DS-K1T680DF DS-K1T680DFW DS-K1T680DFG DS-K1T680DFG1 Use only power supplies listed in the user instructions: Model Manufacturer Standard ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PDE ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.
DS-K1T680 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation ........................................................................................................ 29 7.1 Login .................................................................................................................................... 29 7.1.1 Login by Administrator ................................................................................................ 29 7.1.2 Login by Activation Password .............
DS-K1T680 Series Face Recognition Terminal User Manual 7.9 Time and Attendance Status Settings .................................................................................. 50 7.9.1 Disable Attendance Mode via Device ......................................................................... 50 7.9.2 Set Manual Attendance via Device ............................................................................. 51 7.9.3 Set Auto Attendance via Device ........................................................
DS-K1T680 Series Face Recognition Terminal User Manual 8.5.12 Set Supplement Light Brightness .............................................................................. 70 8.5.13 Time and Attendance Settings .................................................................................. 71 8.5.14 Set Video Intercom Parameters ................................................................................ 73 8.5.15 Set Access Control and Authentication Parameters .....................................
DS-K1T680 Series Face Recognition Terminal User Manual 9.4.8 Collect Fingerprint via Access Control Device ............................................................. 99 9.4.9 Configure Access Control Information ........................................................................ 99 9.4.10 Customize Person Information ................................................................................ 101 9.4.11 Configure Resident Information ..............................................................
DS-K1T680 Series Face Recognition Terminal User Manual 9.8 Configure Linkage Actions for Access Control .................................................................... 131 9.8.1 Configure Client Actions for Access Event ................................................................. 131 9.8.2 Configure Device Actions for Access Event ............................................................... 132 9.8.3 Configure Device Actions for Card Swiping .....................................................
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features • • • • • • • • • • • • • • • • • • • • • • • 8-inch touch screen with bezel-less design Presents card on the screen to authenticate card permission.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No. 1 Description microUSB Interface Note USB to micro USB cable is included in the package.
DS-K1T680 Series Face Recognition Terminal User Manual No. Description Note • If the device supports PoE, the network interface supports power supply by PoE. • If the device supports power supply by PoE and the network interface is connected, do not wire the power input terminal.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment • Avoid backlight, direct sunlight, and indirect sunlight. • For better recognition, there should be light source in or near the installation environment. • If you have to install the device outdoors, you should install a protective shield (optional) for the device. Note For details about installation environment, see Tips for Installation Environment. 3.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 3-2 Secure the Decoration Plate on the Base Plate 3. Dig a hole (242 mm × 114 mm × 30.5 mm) on the wall. Place a gang box in the hole (a), and remove the 4 mounting ears with tool (b). Secure the combination and the gang box with 1 screw (c).
DS-K1T680 Series Face Recognition Terminal User Manual 3.3 Surface Mounting Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation. After the installation, the equipment, including any associated mounting plate, shall not be damaged. 1. According to the datum line on the mounting template, stick the mounting template on the wall or other surfaces, 1.4 meters higher than the ground.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 3-4 Mounting Template 2. Drill holes on the wall or other surface according to the Hole 1 and Hole 2 on the mounting template. 3. Remove the cable hole on the mounting plate with tools. 4. Align the holes to the mounting plate and secure the mounting plate on the wall with the 4 supplied screws (Pa4×25).
DS-K1T680 Series Face Recognition Terminal User Manual Figure 3-5 Install Mounting Plate 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding external devices' cables. 6. Align the device with the mounting plate and hang the device on the mounting plate. Figure 3-6 Hang Device 7. Use 2 supplied screw (KM3×6) to secure the device and the mounting plate.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 3-7 Secure Device 9
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, the exit button, the alarm output/input devices, the Wiegand card reader, the access controller, and the power supply. You can wire the peripherals according to the descriptions below.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 4-1 Terminal Diagram The descriptions of the terminals are as follows: Table 4-1 Terminal Descriptions Group Group A No.
DS-K1T680 Series Face Recognition Terminal User Manual Group Group C No.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 4-2 Device Wiring Note • You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. • For details about Wiegand direction settings, see Set Wiegand Parameters . • Do not wire the device to the electric supply directly. 4.
DS-K1T680 Series Face Recognition Terminal User Manual Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module 4.4.1 Wiring Diagram of Door Open When Powering Off Lock Type: Anode Lock, Magnetic Lock, and Electric Bolt (NO) Security Type: Door Open When Powering Off Scenario: Installed in Fire Engine Access Type 1 Note The fire system controls the power supply of the access control system.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 4-5 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 4-7 Wiring Secure Door Control Unit 4.4.2 Wiring Diagram of Door Locked When Powering Off Lock Type: Cathode Lock, Electric Lock, and Electric Bolt (NC) Security Type: Door Locked When Powering Off Scenario: Installed in Entrance/Exit with Fire Linkage Note • The Uninterpretable Power Supply (UPS) is required. • The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 4-8 Device Wiring Figure 4-9 Wiring Diagram 17
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 5.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T680 Series Face Recognition Terminal User Manual • After activation, if you need to operate the device remotely via APP, you should scan the QR code to link to the APP. For details, see Link to Mobile Client . • After activation, if you need to add administrator to manage the device parameters, you should set administrator. For details, see Add Administrator . 5.2 Activate via Web Browser You can activate the device via the web browser. Steps 1. Enter the device default IP address (192.0.0.
DS-K1T680 Series Face Recognition Terminal User Manual Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4.
DS-K1T680 Series Face Recognition Terminal User Manual 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6. Create a password in the password field, and confirm the password. Caution The password strength of the device can be automatically checked.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language 6.2 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 6-2 Welcome Page 2. Tap OK to save. • • • • Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. When you enter the Select Network page, tap Wired Network or Wi-Fi for your actual needs. Figure 6-3 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway.
DS-K1T680 Series Face Recognition Terminal User Manual Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.4 Link to Mobile Client After activation, selecting application mode, selecting networking, you can add the device to the mobile client. Download and install the mobile client. Use the scan QR code function of the mobile client and scan the QR code displayed on the device to link the device to the mobile client.
DS-K1T680 Series Face Recognition Terminal User Manual Before You Start Activate the device and select an application mode. Steps 1. Optional: Tap Skip to skip adding administrator if required. 2. Enter the administrator's name (optional) and tap Next. Figure 6-5 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm.
DS-K1T680 Series Face Recognition Terminal User Manual Status Icon Description / Device is armed/not armed. / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. 3G/4G is enabled. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . Scan QR code to authenticate.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page. Figure 7-1 Admin Login 2.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap 4. Optional: Tap and you can enter the device activation password for login. and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1.
DS-K1T680 Series Face Recognition Terminal User Manual Note The device will be locked for 30 minutes after 5 failed password attempts. Figure 7-3 Home Page 7.2 Communication Settings You can set the network parameters, the Wi-Fi parameter, the RS-485 parameters, the Wiegand parameters, and enable 3G/4G on the communication settings page. 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, and the gateway.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wired Network. Figure 7-4 Wired Network Settings 3. Set DHCP, IP Address, Subnet Mask, or Gateway. Note The device's IP address and the computer IP address should be in the same IP segment. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K1T680 Series Face Recognition Terminal User Manual 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external access controller, secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap RS-485 to enter the RS-485 tab. Figure 7-6 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. • Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 34.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID. Note • The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. • The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard.
DS-K1T680 Series Face Recognition Terminal User Manual Note • For details about adding a face picture, see Add Face Picture . • Note For details about adding a fingerprint, see Add Fingerprint . • For details about adding a card, see Add Card . • For details about adding a password, see View Password . 6. Optional: Set the administrator's authentication type. Note For details about setting the authentication type, see Set Authentication Mode . 7. Enable the Administrator Permission function.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-8 Add Face Picture 6. Look at the camera. Note • Make sure your face picture is in the face picture outline when adding the face picture. • Make sure the captured face picture is in good quality and is accurate. • For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page.
DS-K1T680 Series Face Recognition Terminal User Manual Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10. Tap to save the settings. 7.3.3 Add Fingerprint Add a fingerprint for the user and the user can authenticate via the added fingerprint. Steps Note • The function should be supported by the device. • Up to 10,000 fingerprints can be added. 1.
DS-K1T680 Series Face Recognition Terminal User Manual The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 8. Tap to save the settings. 7.3.4 Add Card Add a card for the user and the user can authenticate via the added card. Steps Note Up to 100,000 cards can be added. 1.
DS-K1T680 Series Face Recognition Terminal User Manual 8. Configure the card type. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10. Tap to save the settings. 7.3.
DS-K1T680 Series Face Recognition Terminal User Manual The User is the normal user. The user can only authenticate or take attendance on the initial page. 7. Tap to save the settings. 7.3.6 Set Authentication Mode After adding the user's face picture, password, or other credentials, you should set the authentication mode and the user can authenticate his/her identity via the configured authentication mode. Steps 1.
DS-K1T680 Series Face Recognition Terminal User Manual 7.4 Data Management You can delete data, import data, and export data. 7.4.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data or Face Data. 4. Enter the created password when you exported the data.
DS-K1T680 Series Face Recognition Terminal User Manual 7.4.3 Export Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Export Data . 3. Tap Event Data, User Data, or Face Data. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password. Note • The supported USB flash drive format is DB. • The system supports the USB flash drive with the storage of 1G to 32G.
DS-K1T680 Series Face Recognition Terminal User Manual Note The card can be normal IC card, or encrypted card. QR Code Put the QR code in front of the device camera to authenticate via QR code. Note Authentication via QR code should be supported by the device. Password Enter the password to authenticate via password. If authentication completed, a prompt "Authenticated" will pop up. 7.5.2 Authenticate via Multiple Credential Before You Start Set the user authentication type before authentication.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-9 Basic Settings Page shortcut key, voice, time, language, supplement light, community No., building No., and Unit No. Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function. Note You can select call type from Call Room, Call Center, and Call Specified Room No.
DS-K1T680 Series Face Recognition Terminal User Manual Note You can set the voice volume between 0 and 10. Time Settings Set the time zone, the device time and the DST. Language Select the language according to actual needs. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance.
DS-K1T680 Series Face Recognition Terminal User Manual Parameter Face Recognition Interval Description The time interval between two continuous face recognitions when authenticating. Note You can input the number from 1 to 10. Wide Dynamic It is suggested to enable the WDR function if installing the device outdoors.
DS-K1T680 Series Face Recognition Terminal User Manual Parameter Description If the person do not wear the hard hat when authenticating, the device prompts and the door keeps closed. 7.8 Set Access Control Parameters You can set the access control permissions, including the functions of authentication mode, enable NFC card, door contact, and door open time. On the Home page, tap ACS (Access Control Settings) to enter the Access Control Settings page. Edit the access control parameters on this page.
DS-K1T680 Series Face Recognition Terminal User Manual Parameter Description Note • Only the device with the fingerprint module supports the fingerprint related function. • Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. • If you adopt multiple authentication modes, you should authenticate other methods before authenticating face. Reader Auth.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-12 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode.
DS-K1T680 Series Face Recognition Terminal User Manual 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication. Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. 7.9.
DS-K1T680 Series Face Recognition Terminal User Manual The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap Confirm. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 7-15 Manual and Auto Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K1T680 Series Face Recognition Terminal User Manual 7.10 System Maintenance You can view the system information and the capacity. You can also upgrade the device, restore to factory settings, restore to default settings, and reboot the device. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and login the home page. Tap Maint.. Figure 7-16 Maintenance Page System Information You can view the device model, serial No.
DS-K1T680 Series Face Recognition Terminal User Manual Plug the USB flash drive in the device USB interface. Tap Upgrade, and the device will read the digicap.dav file in the USB flash drive to start upgrading. Unlink APP Account After unlinking APP account, you cannot operate via APP. Restore to Default Settings All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect.
DS-K1T680 Series Face Recognition Terminal User Manual 7.11.2 Call Center from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the main station and the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K1T680 Series Face Recognition Terminal User Manual Note For details about operations in the Live View page, see Live View in the user manual of the client software. 6. Right click the live view image to open the right-click menu. 7. Click Start Two-Way Audio to start two-way audio between the device and the client software. 7.11.4 Call Room from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K1T680 Series Face Recognition Terminal User Manual Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Unlock the linked door. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream.
DS-K1T680 Series Face Recognition Terminal User Manual Click Save to save the settings. Add Face Picture Click User → Add to enter the Add Person page. Click + on the right to upload a face picture from the local PC. Note The picture format should be JPEG and the size should be less than 200K. Click Save to save the settings. Add Authentication Mode Click User → Add to enter the Add Person page. Set the authentication mode. Click Save to save the settings. 8.
DS-K1T680 Series Face Recognition Terminal User Manual Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 8.5 Configuration 8.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path. Set Live View Parameters Click Configuration → Local to enter the Local page.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 8-3 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.5.4 Set DST Steps 1.
DS-K1T680 Series Face Recognition Terminal User Manual 8.5.6 Upgrade and Maintenance Reboot device, restore device parameters, and upgrade device version. Reboot Device Click Configuration → System → Maintenance → Upgrade & Maintenance . Figure 8-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings.
DS-K1T680 Series Face Recognition Terminal User Manual Click and select the file to import. Click Import to start import configuration file. Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. Note Do not power off during the upgrading. 8.5.7 Security Mode Settings Set the security mode for logging in the client software.
DS-K1T680 Series Face Recognition Terminal User Manual 8.5.9 Network Settings Set TCP/IP, port, Wi-Fi parameters, report strategy and platform access. Note Some device models do not support Wi-Fi settings. Refer to the actual products when configuration. Set Basic Network Parameters Click Configuration → Network → Basic Settings → TCP/IP . Figure 8-6 TCP/IP Settings Page Set the parameters and click Save to save the settings.
DS-K1T680 Series Face Recognition Terminal User Manual It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. RTSP It refers to the port of real-time streaming protocol. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device.
DS-K1T680 Series Face Recognition Terminal User Manual 2) Set the IP address, subnet mask, and default gateway. Or check Enable DHCP and the system will allocate the IP address, subnet mask, and default gateway automatically. 5. Click Save. Report Strategy Settings You can set the center group for uploading the log via the ISUP protocol. Go to Configuration → Network → Basic Settings → Report Strategy . You can set the center group and the system will transfer logs via ISUP protocol.
DS-K1T680 Series Face Recognition Terminal User Manual 8.5.10 Set Video and Audio Parameters Set the image quality, resolution, and the device volume. Set Video Parameters Click Configuration → Video/Audio → Video . Figure 8-8 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, and the Max. bitrate. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio .
DS-K1T680 Series Face Recognition Terminal User Manual Figure 8-9 Image Settings Page 2. Configure the parameters to adjust the image. Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect. PAL 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc. NTSC 30 frames per second.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Click Configuration → Image → Supplement Light Parameters . Figure 8-10 Supplement Light Settings Page 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 8.5.
DS-K1T680 Series Face Recognition Terminal User Manual Note Set the schedule from Monday to Sunday according to the actual needs. 5. Optional: Select a timeline and click Delete. Or click Delete All to clear the settings. 6. Click Save. Set Manual Attendance via Web Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1.
DS-K1T680 Series Face Recognition Terminal User Manual Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule. Refers to Time Settings for details. Set Manual and Auto Attendance via Web Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 8-11 Device No. Settings Click Save to save the settings after the configuration. Device Type The device can be used as a door station or outer door station. Select a device type from the drop-down list. Note If you change the device type, you should reboot the device. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. Floor No.
DS-K1T680 Series Face Recognition Terminal User Manual 8.5.15 Set Access Control and Authentication Parameters Set the access control parameters and the authentication parameters. Set Authentication Parameters Click Configuration → Access Control → Authentication Settings . Figure 8-12 Authentication Parameters Settings Click Save to save the settings after the configuration. Authentication Select an authentication mode according to your actual needs from the drop-down list.
DS-K1T680 Series Face Recognition Terminal User Manual Open Timeout Alarm (Door Open Timeout Alarm) An alarm will be triggered if the door has not been closed within the configured time duration. 8.5.16 Set Card Security Click Configuration → Access Control → Card Security to enter the settings page. Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data.
DS-K1T680 Series Face Recognition Terminal User Manual Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, Access Controller, or Disable. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T680 Series Face Recognition Terminal User Manual Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 8.5.20 Set Biometric Parameters Set Basic Parameters Click Configuration → Smart → Smart . Figure 8-15 Smart Settings Page Click Save to save the settings after the configuration.
DS-K1T680 Series Face Recognition Terminal User Manual Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T680 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate Hard Hat Detection After enabling the hard hat detection, you can set the strategy.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 8-16 Notice Page Sleep Enable Sleep and the device will enter the sleep mode when no operation with the configured sleep time. Customize Screen Saver Enable the function, and you can upload the screen saver pictures from the local PC. You can also set the slide show interval for the screen saver.
DS-K1T680 Series Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T680 Series Face Recognition Terminal User Manual 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices.
DS-K1T680 Series Face Recognition Terminal User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T680 Series Face Recognition Terminal User Manual The searched online devices are displayed in the list. 4. Select multiple devices. Note For the inactive device, you need to create the password for it before you can add the device properly. For details, refer to . 5. Click Add to open the device adding window. 6. Enter the required information. User Name By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T680 Series Face Recognition Terminal User Manual 3. Click Add to open the Add window, and then select IP/Domain as the adding mode. 4. Enter the required information. Name Create a descriptive name for the device. For example, you can use a nickname that can show the location or feature of the device. Address The IP address or domain name of the device. Port The devices to add share the same port number. The default value is 8000. User Name Enter the device user name.
DS-K1T680 Series Face Recognition Terminal User Manual Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Finish adding the device. - Click Add to add the device and back to the device list page. - Click Add and New to save the settings and continue to add other device. Add Devices by IP Segment If the devices share the same port No.
DS-K1T680 Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 6. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS (Transport Layer Security) protocol for security purpose . Note • This function should be supported by the device.
DS-K1T680 Series Face Recognition Terminal User Manual Note This function should be supported by the device. 5. Optional: Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 6. Optional: Check Import to Group to create a group by the device name, and import all the channels of the device to the group. 7. Finish adding the device. - Click Add to add the device and go back to the device list.
DS-K1T680 Series Face Recognition Terminal User Manual Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T680 Series Face Recognition Terminal User Manual - Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support. Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked.
DS-K1T680 Series Face Recognition Terminal User Manual Note The resources (such as alarm inputs/outputs, access points, etc.) of this device will be imported to the group by default. 9.3.2 Import Resources to Group You can import the device resources (such as alarm inputs/outputs, access points, etc.) to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2.
DS-K1T680 Series Face Recognition Terminal User Manual 9.3.4 Remove Resources from Group You can remove the added resources from the group. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 9.
DS-K1T680 Series Face Recognition Terminal User Manual Show Persons in Sub Organization Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations. 9.4.2 Configure Basic Information You can add person to the client software one by one and configure the person's basic information such as name, gender, phone number, etc. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person. 3.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-2 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
DS-K1T680 Series Face Recognition Terminal User Manual This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. 4. 5. 6. Click Add Face in the Basic Information panel. Select Take Photo. Connect the face scanner to the PC running the client.
DS-K1T680 Series Face Recognition Terminal User Manual 3) Click OK to save the captured photo. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons . 9.4.7 Collect Fingerprint via Client Collecting fingerprints locally means you can collect the fingerprint via the fingerprint recorder connected directly to the PC running the client.
DS-K1T680 Series Face Recognition Terminal User Manual 9.4.8 Collect Fingerprint via Access Control Device When adding person, you can collect fingerprint information via the access control device's fingerprint module. The fingerprints recorded can be used as credentials of the persons to access the authorized doors. Before You Start Make sure fingerprint collection is supported by the access control device. Steps 1. Enter Person module. 2.
DS-K1T680 Series Face Recognition Terminal User Manual Note For details, refer to Set Access Group to Assign Access Authorization to Persons . Figure 9-3 Configure Access Control Information 4. Set a unique PIN code for the person which can be used for access authentication. - Manually enter a PIN code containing 4 to 8 digits. Note Persons' PIN codes cannot be repeated. - Click Generate to randomly generate an unrepeated PIN code of 6 digits.
DS-K1T680 Series Face Recognition Terminal User Manual Note The valid times for visit is between 1 and 100. You can also check No Limit, then there are no limited times for the visitor to access doors/floors. Device Operator For person with device operator role, he/she is authorized to operate on the access control devices. Note The Super User, Extended Door Open Time, Add to Blocklist, and Mark as Visitor functions cannot be enabled concurrently.
DS-K1T680 Series Face Recognition Terminal User Manual 9.4.11 Configure Resident Information If the person is resident, for video intercom purpose, you need to set the room number for her/him and bind an indoor station. After bound, you can call this person by calling the indoor station and perform video intercom with her/him. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first.
DS-K1T680 Series Face Recognition Terminal User Manual 9.4.13 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. 9.4.14 Import Person Information You can enter the information of multiple persons in a predefined template (a CSV file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2.
DS-K1T680 Series Face Recognition Terminal User Manual 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. 5. Click to select a face picture file. Note • The (folder of) face pictures should be in ZIP format.
DS-K1T680 Series Face Recognition Terminal User Manual Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. Note • The exported file is in ZIP format. • The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 9.4.
DS-K1T680 Series Face Recognition Terminal User Manual 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5. Select the organization to move persons to. 6. Click OK. 9.4.20 Issue Cards to Persons in Batch The client provides a convenient way to issue cards to multiple persons in a batch. Steps 1. Enter Person module. 2. Click Batch Issue Cards.
DS-K1T680 Series Face Recognition Terminal User Manual 5. If the lost card is added in one access group and the access group is applied to the device already, after reporting card loss or cancelling card loss, a window will pop up to notify you to apply the changes to the device. After applying to device, these changes can take effect on the device. 9.4.
DS-K1T680 Series Face Recognition Terminal User Manual Remote Mode: Issue Card by Card Reader Select an access control device added in the client and swipe the card on its card reader to read the card number. 9.5 Configure Schedule and Template You can configure the template including holiday and week schedule. After setting the template, you can adopt the configured template to access groups when setting the access groups, so that the access group will take effect in the time durations of the template.
DS-K1T680 Series Face Recognition Terminal User Manual • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog. • Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to .
DS-K1T680 Series Face Recognition Terminal User Manual • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog. • Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to . 4) Repeat the two steps above to draw more time durations on the other days of the week. 6.
DS-K1T680 Series Face Recognition Terminal User Manual Note You should configure the template before access group settings. Refer to Configure Schedule and Template for details. 5. In the left list of the Select Person field, select person(s) to assign access authority. 6. In the left list of the Select Access Point field, select door(s), door station(s) or floor(s) for the selected persons to access. 7. Click Save.
DS-K1T680 Series Face Recognition Terminal User Manual Note You can check Display Failure Only to filter the applying results. The selected persons in the applied access groups will have the authorization to enter/exit the selected doors/door stations with their linked card(s) or fingerprints. 9. Optional: Click to edit the access group if necessary.
DS-K1T680 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T680 Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Enable CPU Card Reserved. If enable the function, the device can recognize the CPU card. You can present CPU card on the device. Enable ID Card Reserved. If enable the function, the device can recognize the ID card. You can present ID card on the device. 4. Click OK. 5.
DS-K1T680 Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event.
DS-K1T680 Series Face Recognition Terminal User Manual Name Edit the card reader name as desired. Minimum Card Swiping Interval If the interval between card swiping of the same card is less than the set value, the card swiping is invalid. You can set it as 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only.
DS-K1T680 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate when authentication. Application Mode You can select indoor or others application modes according to actual environment.
DS-K1T680 Series Face Recognition Terminal User Manual • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog. • Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to . 4) Click Save.
DS-K1T680 Series Face Recognition Terminal User Manual Before You Start Set access group and apply the access group to the access control device. For details, refer to Set Access Group to Assign Access Authorization to Persons . Perform this task when you want to set authentications for multiple cards of one access control point (door). Steps 1. Click Access Control → Advanced Function → Multi-Factor Auth . 2. Select an access control device in device list on the left panel. 3.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-7 Remotely Open Door Note You can check Offline Authentication to enable the super password authentication when the access control device is disconnected with the client. Local Authentication and Super Password Authentication by the access control device and by the super password. 4) Select the added person/card group in the left list below and it will be added to the Selected list on the right as the authentication group.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Click Access Control → Advanced Function → Authentication to enter the authentication mode configuration page. 2. Select a card reader on the left to configure. 3. Set card reader authentication mode. 1) Click Configuration. Figure 9-8 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information .
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-9 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 9.7.5 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K1T680 Series Face Recognition Terminal User Manual Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Note You can authenticate by the first person again to disable the first person mode. 4. Click Add on the First Person List panel. 5.
DS-K1T680 Series Face Recognition Terminal User Manual Note Up to four afterward card readers can be added for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save at the upper-right corner of Anti-Passback page to save the settings and take effect. Note Super credentials, such as super card, super password, super fingerprint, and so on, have the privilege of not following the anti-passback rules.
DS-K1T680 Series Face Recognition Terminal User Manual 5. Click OK to add the selected access control point(s) for interlocking. The configured multi-door interlocking combination will list on the Multi-door Interlocking List panel. 6. Optional: Select an added multi-door interlocking combination from the list and click Delete to delete the combination. 7. Click Apply to apply the settings to the access control device. 9.7.
DS-K1T680 Series Face Recognition Terminal User Manual Steps Note Make sure the device is not added by ISUP. 1. 2. 3. 4. 5. 6. Enter the Access Control module. On the navigation bar on the left, enter Advanced Function → More Parameters . Select an access control device in the device list and enter Network → Uploading Mode . Select the center group from the drop-down list. Check Enable to enable to set the uploading mode. Select the uploading mode from the drop-down list.
DS-K1T680 Series Face Recognition Terminal User Manual Set Device Capture Parameters You can configure the capture parameters of the access control device, including manual capture and event triggered capture. Note • The capture function should be supported by the device. • Before setting the capture parameters, you should set the picture storage first to define where the event triggered pictures are saved. For details, refer to Set Picture Storage in the user manual of the client software. .
DS-K1T680 Series Face Recognition Terminal User Manual Before You Start Before setting the capture parameters, you should set the saving path first to define where the captured pictures are saved. For details, refer to Set Picture Storage in the user manual of the client software. Steps Note This function should be supported by the device 1. 2. 3. 4. 5. Enter the Access Control module. On the navigation bar on the left, enter Advanced Function → More Parameters → Capture .
DS-K1T680 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode Threshold When enabling the ECO mode, you can set the ECO mode's threshold.
DS-K1T680 Series Face Recognition Terminal User Manual Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. After setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand communication. Steps Note This function should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3.
DS-K1T680 Series Face Recognition Terminal User Manual Note • The sector ID ranges from 1 to 100. • By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 9.8 Configure Linkage Actions for Access Control You can configure different linkage actions for the event detected by the access control device. After that, linkage actions will be triggered once the event happens.
DS-K1T680 Series Face Recognition Terminal User Manual The client software gives an audible warning when alarm is triggered. You can select the alarm sound for audible warning. Note For setting the alarm sound, please refer to Set Alarm Sound in the user manual of client software.. Send Email Send an email notification of the alarm information to one or more receivers. For details about setting email parameters, refer to Set Email Parameters in the user manual of client software.. 2) Click OK. 5.
DS-K1T680 Series Face Recognition Terminal User Manual Note The target door and the source door cannot be the same one. 7. Click Save. 8. Optional: After adding the device linkage, you can do one or more of the following: Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. 9.8.
DS-K1T680 Series Face Recognition Terminal User Manual Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 9.8.4 Configure Device Actions for Person ID You can set the access control device's linkage actions for the specified person ID. When access control device detects the specified person ID, it can trigger buzzer on card reader, and other actions.
DS-K1T680 Series Face Recognition Terminal User Manual Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 9.9 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device. You can also control the doors such as open/close the door, or remain the door open/closed via the client remotely.
DS-K1T680 Series Face Recognition Terminal User Manual Remain Closed The door will be closed and locked. No person can access the door even if he/she has the authorized credentials, except the super users. Capture Capture a picture manually. Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in the user manual of the client software.
DS-K1T680 Series Face Recognition Terminal User Manual 9.10 Event Center The event information (for example, device offline) received by the client displays. In the Event Center, you can check the detailed information of the real-time and historical events, view the event linked video, handle the events, and so on. Before the client can receive the event information from the device, you need to enable the events of the resource and arm the device first.
DS-K1T680 Series Face Recognition Terminal User Manual Steps 1. Click Event Center → Real-time Event to enter the real-time event page and you can view the real-time events received by the client. Event Time For encoding device, event time is the client time when it receives the event. For other device types, event time is the time when the event is triggered. Priority Priority represents the emergency degree of the event. 2. Filter the events.
DS-K1T680 Series Face Recognition Terminal User Manual Enlarge Video or Picture • Double click the video image to view video in a larger window. • Put the cursor on the picture, and click to view picture in a larger window. Download Captured Picture Hover the cursor on the captured picture, and click the download icon on the lower right corner of the picture to download it to the local PC.
DS-K1T680 Series Face Recognition Terminal User Manual Device: Search the events occurred on the selected device. Device Type The type of device that occurred the event. All All the device types, and you can set the following filter conditions: group, priority, and status. Video Intercom For the events of video intercom, you need to select searching scope: All Record and Only Unlocking.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-12 Customize Event Related Items to be Displayed 5. Optional: Handle the event(s). - Handle single event: Select one event that need to be processed, and then click Handle in the event information details page, and enter the processing suggestion. - Handle events in a batch: Select the events which need to be processed, and then click Handle in Batch, and enter the processing suggestion.
DS-K1T680 Series Face Recognition Terminal User Manual 9.11 Time and Attendance The Time and Attendance module provides multiple functionalities to track and monitor when employees start and stop work, and full control of employees working hours such as late arrivals, early departures, time taken on breaks and absenteeism. Note In this section, we introduce the configurations before you can getting the attendance reports.
DS-K1T680 Series Face Recognition Terminal User Manual When you work for a certain period after end-work time on workday, you will reach different overtime level: overtime level 1, overtime level 2 and overtime level 3. You can set different work hour rate for three overtime levels, respectively. Work Hour Rate Work Hour Rate is used to calculate work hours by multiplying it by overtime. When you work for a certain period after end-work time on workday, you will reach different overtime level.
DS-K1T680 Series Face Recognition Terminal User Manual Add Regular Holiday You can configure a holiday which will take effect annually on regular days during the effective period, such as New Year's Day, Independence Day, Christmas Day, etc. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Holiday to enter the Holiday Settings page. 3. Check Regular Holiday as holiday type. 4. Custom a name for the holiday. 5. Set the first day of the holiday. 6.
DS-K1T680 Series Face Recognition Terminal User Manual The added holiday will display in the holiday list and calendar. If the date is selected as different holidays, it will be recorded as the first-added holiday. 11. Optional: After adding the holiday, perform one of the following operations. Edit Holiday Click to edit the holiday information. Delete Holiday Select one or more added holidays, and click Delete to delete the holiday(s) from the holiday list.
DS-K1T680 Series Face Recognition Terminal User Manual Note If you select MySql, you should import the configuration file (libmysql.dll) from local PC. 5. Set the other required parameters of the third-party database, including server IP address, database name, user name and password. 6. Set table parameters of database according to the actual configuration. 1) Enter the table name of the third-party database. 2) Set the mapped table fields between the client software and the third-party database. 7.
DS-K1T680 Series Face Recognition Terminal User Manual The fixed break duration will be excluded from work hours. Must Check The break duration will be calculated and excluded from work hours according to actual check-in and check-out time. Note If you select Must Check as calculation method, you need to set attendance status for late or early returning from break. 6. Click Save to save the settings. 7. Optional: Click Add to continue adding break time.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-13 Add Timetable 3. Create a name for the timetable. Note You can click the color icon beside the name to customize the color for the valid timetable on the time bar in the Configuration Result area. 4. Select the timetable type as general. 5. Select calculation method. First In & Last Out The first check-in time is recorded as start work time and the last check-out time is recorded as the end-work time.
DS-K1T680 Series Face Recognition Terminal User Manual Note This function should be supported by the device. 7. Set the related attendance time parameters as the following: Start/End-Work Time Set the start-work time and end-work-time. Valid Check-in/out Time On the time bar, adjust the yellow bar to set the timetable during which the check-in or check-out is valid. Calculated as Set the duration calculated as the actual work duration. Late/Early Leave Allowable Set the timetable for late or early leave. 8.
DS-K1T680 Series Face Recognition Terminal User Manual Before You Start Add a timetable first. See Add General Timetable for details. Steps 1. Click Time & Attendance → Shift to enter shift settings page. 2. Click Add to enter Add Shift page. 3. Enter the name for shift. 4. Select the shift period from the drop-down list. 5. Select the added timetable and click on the time bar to apply the timetable. Figure 9-14 Add Shift Note You can select more than one timetables.
DS-K1T680 Series Face Recognition Terminal User Manual Figure 9-15 Add Multiple Timetables 6. Click Save. The added shift lists on the left panel of the page. At most 64 shifts can be added. 7. Optional: Assign the shift to organization or person for a quick shift schedule. 1) Click Assign. 2) Select Organization or Person tab and check the desired organization(s) or person(s) box. The selected organizations or persons will list on the right page. 3) Set the Expire Date for the shift schedule.
DS-K1T680 Series Face Recognition Terminal User Manual 9.11.4 Manage Shift Schedule Shift work is an employment practice designed to make use of all 24 hours of the clock each day of the week. The practice typically sees the day divided into shifts, set periods of time during which different shifts perform their duties. You can set department schedule, person schedule, and temporary schedule.
DS-K1T680 Series Face Recognition Terminal User Manual Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work. Scheduled on Holidays On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule. Effective for Overtime The persons' overtime will be recorded for this schedule. 8. Click Save.
DS-K1T680 Series Face Recognition Terminal User Manual Check-in Not Required Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work. Scheduled on Holidays On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule. Effective for Overtime The persons' overtime will be recorded for this schedule. 8. Click Save.
DS-K1T680 Series Face Recognition Terminal User Manual effective in any of the three timetables. If the person checks in at 07:50, it will apply the nearest timetable 08:00 to 15:00 to the person's attendance. Rule Set other rule for the schedule, such as Check-in Not Required, andCheck-out Not Required. 6. Click Save. Check Shift Schedule You can check the shift schedule in calendar or list mode. You ca also edit or delete the shift schedule. Steps 1.
DS-K1T680 Series Face Recognition Terminal User Manual Note You can click supported. to add multiple check in/out items. At most 8 check-in/out items can be 6. Optional: Enter the remark information as desired. 7. Click Save. 8. Optional: After adding the check-in/out correction, perform one of the following operations. View Click or mode.
DS-K1T680 Series Face Recognition Terminal User Manual 6. 7. 8. 9. Set the time for leave. Optional: Enter the remark information as desired. Click Save. Optional: After adding the leave and business trip, perform one of the following operations. View Click or mode. to view the added attendance handling information in calendar or list Note In calendar mode, you need to click Calculate to get the attendance status of the person in one month.
DS-K1T680 Series Face Recognition Terminal User Manual The client will calculate the attendance data of the previous day from the time you have configured. Manually Calculate Attendance Data You can calculate the attendance data manually by setting the data range. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Calculation . 3. Set the start time and end time to define the attendance data range. 4.
DS-K1T680 Series Face Recognition Terminal User Manual Note • The client will automatically calculate the previous day's attendance data at 1:00 am on the next day. • Keep the client running at 1:00 am or it cannot calculate the previous day's attendance data automatically. If not calculated automatically, you can calculate the attendance data manually. For details, refer to Manually Calculate Attendance Data . Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Attendance Record .
DS-K1T680 Series Face Recognition Terminal User Manual 5. Set the start time and end time during which the attendance data will be displayed in the report. 6. Click Report to generate the statistics report and open it. Custom Attendance Report The client supports multiple report types and you can pre-define the report content and it can send the report automatically to the email address you configured. Steps Note Set the email parameters before you want to enable auto-sending email functions.
DS-K1T680 Series Face Recognition Terminal User Manual Note Make sure the attendance records are calculated before the sending time. You can calculate the attendance data manually, or set the schedule so that the client can calculate the data automatically every day. For details, refer to Calculate Attendance Data . 5) Enter the receiver email address(es). Note You can click + to add a new email address. Up to 5 email addresses are allowed. 6) Optional: Click Preview to view the email details. 6. Click OK.
DS-K1T680 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T680 Series Face Recognition Terminal User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
DS-K1T680 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. • Do not make your hair cover your eyes, ears, etc.
DS-K1T680 Series Face Recognition Terminal User Manual 165
DS-K1T680 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K1T680 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T680 Series Face Recognition Terminal User Manual Figure D-2 Dimension with Bracket 168
DS-K1T680 Series Face Recognition Terminal User Manual Appendix E.
DS-K1T680 Series Face Recognition Terminal User Manual Appendix F. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure F-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD21056B-B