DS-K5604A-3XF Series Face Recognition Terminal User Manual
DS-K5604A-3XF Series Face Recognition Terminal User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K5604A-3XF Series Face Recognition Terminal User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K5604A-3XF Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K5604A-3XF Series Face Recognition Terminal User Manual • The device cover for indoor use shall be kept from rain and moisture. • Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K5604A-3XF/V Use only power supplies listed in the user instructions: Model Manufacturer Standard C2000IC12.0-24P-DE MOSO Power Supply Technology Co., Ltd. CEE C2000IC12.0-24P-GB MOSO Power Supply Technology Co., Ltd. BS KPL-040F-VI Channel Well Technology Co Ltd.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.4.2 Add Face Picture ......................................................................................................... 20 6.4.3 Add Card ..................................................................................................................... 22 6.4.4 Add Password .............................................................................................................. 23 6.4.5 Set Authentication Mode ......................
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.12 View System Information ................................................................................................... 43 6.13 Video Intercom .................................................................................................................. 44 6.13.1 Call Client Software from Device ............................................................................... 44 6.13.2 Call Main Station from Device .......................
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.4.12 Import Person Information ....................................................................................... 67 7.4.13 Import Person Pictures ............................................................................................. 67 7.4.14 Export Person Information ........................................................................................ 68 7.4.15 Export Person Pictures ...............................................
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.9.2 Check Real-Time Access Records .............................................................................. 100 7.10 Event Center .................................................................................................................... 100 7.10.1 Enable Receiving Event from Devices ..................................................................... 101 7.10.2 View Real-Time Events ................................................
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.12.14 Configure Face Picture Parameters ....................................................................... 132 7.12.15 Configure Supplement Light Parameters .............................................................. 133 7.12.16 Set Device No. ....................................................................................................... 133 7.12.17 Configure Video and Audio Parameters ..............................................
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features • Plug & play Supports rapid deployment. Free of wiring, installation, or configuration.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment • Avoid backlight, direct sunlight, and indirect sunlight. • For better face recognition, there should be light source in or near the installation environment. • Sunlight, wind, hot/cool air from air conditioner and other external factors, which may affect surface temperature, will create the deviation of the temperature measurement.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 3-1 Install Device Note • The device should be installed on the concrete surface or other non-flammable surfaces. • The device supports plug & play. You can put the device on the ground and start operation after powering on.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, and the exit button. You can wire the peripherals according to the descriptions below. Note • If the cable size is 18 AWG, you should use a 12 V switched-mode power supply. And the distance between the power supply and the device should be no more than 20 m. • If the cable size is 15 AWG, you should use a 12 V switched-mode power supply.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 4.2 Wire Device Figure 4-2 Device Wiring Table 4-1 Wiring Terminal Description No.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 4-3 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. • After activation, you should select an application mode.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 7.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 6 Basic Operation 6.1 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-1 Welcome Page 2. Tap OK to save.
DS-K5604A-3XF Series Face Recognition Terminal User Manual • • • • Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-2 Home Page 6.2.2 Login by Administrator After you add the administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s to enter the admin login page.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-3 Admin Login 2. Authenticate the administrator's face or card to enter the home page.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-4 Home Page Note The device will be locked for 30 minutes after 5 failed face or card attempts. 3. Optional: Tap 4. Optional: Tap and you can enter the device activation password for login. and you can exit the admin login page. 6.3 Communication Settings You can set the network parameters, the RS-485 parameters, and the Wiegand parameters on the communication settings page.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.3.1 Set Network Parameters You can set the device network parameters, including the IP address, the subnet mask, and the gateway. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Network to enter the Network tab. Figure 6-5 Network Settings 3. Tap IP Address, Subnet Mask, or Gateway and input the parameters. 4. Tap OK to save the settings.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-6 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs. Note • Controller represents the access controller, Unit represents the secure door control unit and Reader represents the card reader. • If you select Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 4.
DS-K5604A-3XF Series Face Recognition Terminal User Manual • Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or Wiegand 34. • Input: A face recognition terminal can connect a Wiegand card reader. 5. Tap to save the network parameters. Note If you change the external device, and after you save the device parameters, the device will reboot automatically. 6.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note For details about setting the authentication type, see Set Authentication Mode . 7. Enable the Administrator Permission function. Enable Administrator Permission The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. 8. Tap to save the settings. 6.4.2 Add Face Picture Add user's face picture to the device.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-8 Add Face Picture 6. Position your face looking at the camera. Note • Make sure your face picture is in the face picture outline when adding the face picture. • Make sure the captured face picture is in good quality and is accurate. • For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note The maximum duration for adding a face picture is 15s. You can check the remaining time for adding a face picture on the left of the page. 9. Enable or disable the Administrator Permission function. Enable Administrator Permission The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note • The card No. cannot be empty. • Up to 20 characters are allowed in the card No. • The card No. cannot be duplicated. 7. Optional: Enable the Duress Card function. The added card When the user authenticates by swiping this duress card, the device will upload an duress card event to the client software. 8. Enable or disable the Administrator Permission function. Enable Administrator Permission The user is the administrator.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note • Only numbers are allowed in the password. • Up to 8 characters are allowed in the password. 6. Enable or disable the Administrator Permission function. Enable Administrator Permission The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Disable Administrator Permission The User is the normal user.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow the steps in User Management to edit the user parameters. Tap to save the settings. Note The employee ID cannot be edited. 6.5 Temperature Measurement 6.5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Table 6-1 Temperature Measurement Parameters Descriptions Parameter Description Enable Temperature Detection When enabling the function, the device will authenticate the permissions and at the same time take the temperature. When disabling the device, the device will authenticate the permissions only. Over-Temperature Alarm Threshold(Max./Min.) Edit the threshold according to actual situation.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.5.2 Black Body Settings The black body can correct the measuring temperature. You should set the black body parameters if the black body temperature measurement scene is required. If no black bad is required, do not set the black body parameters, or the temperature may not correct.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-10 Black Body Settings Page 2. Enable black body correction function. 3. Put a black body in front of the camera. Make sure there are no other objects between the camera and the black body. 4. Set the distance between the black body and the camera (straight line), and the emissivity of the black body. Note The black body's temperature is fixed. 5. Tap the black body's position on the lower side of the page.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.6 Import and Export Data On the Transfer page, you can export the event, the user data, the user picture, and the captured picture to the USB flash drive. You can also import the user data and the user picture from the USB flash drive. 6.6.1 Export Data Steps 1. Tap Transfer on the Home page to enter the Transfer page. 2. On the Transfer page, tap Export Event, Export User Data, Export Profile Photo, and export captured picture. 3.
DS-K5604A-3XF Series Face Recognition Terminal User Manual • The employee ID should be less than 32 characters. It can be a combination of lower letters, upper letters, and numbers. It should not be duplicated, and should not start with 0. • Requirements of face picture should follow the rules below: It should be taken in full-face view, directly facing the camera. Do not wear a hat or head covering when taking the face picture. The format should be JPEG or JPG.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.7.2 Authenticate via Single Credential Set the user authentication type before authentication. For details, see Set Authentication Mode . Authenticate face, card or QR code. Face Face forward at the camera and start authentication via face. Card Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-11 Basic Parameters Table 6-2 Basic Parameters Parameter Description Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed Unit No. Voice Prompt Tap Voice Volume Adjust the voice volume. The larger the value, the louder the volume. Application Mode You can select either others or indoor according to actual environment.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-12 Face Picture Parameters Table 6-3 Face Picture Parameters Parameter Description 1:N (Security) Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. By default, the value is 84. 1:1 (Security) Level Set the matching threshold when authenticating via 1:1 matching mode.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Parameter Description Note You can enter the number from 1 to 10. Liveness Level (Liveness Security Level) After enabling Live Face Detection function, you can set the matching security level when performing live face authentication. WDR Level The device can auto enable the WDR function. The higher the level, the device can enter the WDR mode easier. 0 represents WDR is disabled.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Parameter Description ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. By default, the value is 75. Face with Mask&Face (1:N) (ECO) Matching threshold for face with mask 1: N in ECO mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The Max.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-14 Access Control Parameters The available parameters descriptions are as follows: Table 6-4 Access Control Parameters Descriptions Parameter Terminal Auth. Mode Description Select the face recognition terminal's authentication mode. You can also customize the authentication mode. Note • Biometric recognition products are not 100% applicable to anti-spoofing environments.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.10 Maintenance 6.10.1 Upgrade Firmware Plug in the USB flash drive. Tap Maint. (Maintenance) on the System Settings page and tap Upgrade. The device will automatically read the upgrading file in the USB flash drive and upgrade the firmware. Note • Do not power off during the device upgrade. • The upgrading file should be in the root directory. • The upgrading file name should be digicap.dav. Figure 6-15 Upgrade 6.10.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Table 6-5 Data Descriptions Parameters Description Delete User Data Delete all user data in the device. Restore to Factory Restore the system to the factory settings. The device will reboot after the setting. Restore to Default Restore the system to the default settings. The system will save the communication settings and the remote user settings. Other parameters will be restored to default. The device will reboot after the settings. 6.10.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.11 Time and Attendance Status Settings Set time and attendance status. You can set the attendance mode as check in, check out, break out, break in, overtime in, and overtime out according to your actual situation. Note The function should be used cooperatively with time and attendance function on the client software. 6.11.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-18 Auto Attendance Mode 3. Select an attendance status and set its schedule. 1) Select Check In, Check Out, Break Out, Break In, Overtime In, or Overtime Out as the attendance status. 2) Tap Schedule. 3) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 4) Tap the select date and set the selected attendance status's start time. 5) Tap Confirm. 6) Repeat step 1 to 5 according to your actual needs.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Manual. Figure 6-19 Manual Attendance Mode 3. Enable the Attendance Status function. Result You should select the attendance status manually after authentication.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 6-20 Manual and Auto Mode 3. Select an attendance status and set its schedule. 1) Select Check In, Check Out, Break Out, Break In, Overtime In, or Overtime Out as the attendance status. 2) Tap Schedule. 3) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 4) Tap the select date and set the selected attendance status's start time. 5) Tap Confirm. 6) Repeat step 1 to 5 according to your actual needs.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.12 View System Information View device capacity, device information, and the open source software license. View Capacity You can view the added user's number, the face picture's number, the face with mask's number, the card's number, and the event's number. Tap Info. (System Information) → Capacity on the Home page to enter the Capacity page. Figure 6-21 Capacity View Device Information You can view the device information. Tap Info.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Open Source License View the Open Source License information. Tap Info. (System Information) → License to enter the Open Source Software Licenses page. View Device QR Code You can add the device to the mobile client by scanning the device QR code. Tap Info. (System Information) → QR Code to view the device QR code. 6.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.13.2 Call Main Station from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the main station and the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6.13.4 Call Indoor Station from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the indoor station and the device to the client software. Note For details about adding device, see Add Device. 5. 6. 7. 8.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Chapter 7 Client Software Configuration 7.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 7-1 Flow Diagram of Configuration on Client Software 7.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K5604A-3XF Series Face Recognition Terminal User Manual The searched online devices are displayed in the list. 4. Select multiple devices. Note For the inactive device, you need to create the password for it before you can add the device properly. For details, refer to . 5. Click Add to open the device adding window. 6. Enter the required information. User Name By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 3. Click Add to open the Add window, and then select IP/Domain as the adding mode. 4. Enter the required information. Name Create a descriptive name for the device. For example, you can use a nickname that can show the location or feature of the device. Address The IP address or domain name of the device. Port The devices to add share the same port number. The default value is 8000. User Name Enter the device user name.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Finish adding the device. - Click Add to add the device and back to the device list page. - Click Add and New to save the settings and continue to add other device. Add Devices by IP Segment If the devices share the same port No.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 6. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS (Transport Layer Security) protocol for security purpose . Note • This function should be supported by the device.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note This function should be supported by the device. 5. Optional: Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 6. Optional: Check Import to Group to create a group by the device name, and import all the channels of the device to the group. 7. Finish adding the device. - Click Add to add the device and go back to the device list.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K5604A-3XF Series Face Recognition Terminal User Manual - Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support. Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note The resources (such as alarm inputs/outputs, access points, etc.) of this device will be imported to the group by default. 7.3.2 Import Resources to Group You can import the device resources (such as alarm inputs/outputs, access points, etc.) to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.3.4 Remove Resources from Group You can remove the added resources from the group. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 7.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Show Persons in Sub Organization Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations. 7.4.2 Configure Basic Information You can add person to the client software one by one and configure the person's basic information such as name, gender, phone number, etc. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person. 3.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 7-2 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E.
DS-K5604A-3XF Series Face Recognition Terminal User Manual This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first. For details, refer to Configure Basic Information . 3. Click Add Face in the Basic Information area. 4. Select Take Photo to enter Take Photo window. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 7.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. 3. In the Access Control area, click to select access group(s) for the person. Note For details, refer to Set Access Group to Assign Access Authorization to Persons . Figure 7-4 Configure Access Control Information 4. Set a unique PIN code for the person which can be used for access authentication.
DS-K5604A-3XF Series Face Recognition Terminal User Manual If the person is a visitor, you should set the her/his valid times for visit. Note The valid times for visit is between 1 and 100. You can also check No Limit, then there are no limited times for the visitor to access doors/floors. Device Operator For person with device operator role, he/she is authorized to operate on the access control devices.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.4.9 Configure Resident Information If the person is resident, for video intercom purpose, you need to set the room number for her/him and bind an indoor station. After bound, you can call this person by calling the indoor station and perform video intercom with her/him. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.4.11 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. 7.4.12 Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. 5. Click to select a face picture file. Note • The (folder of) face pictures should be in ZIP format.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. Note • The exported file is in ZIP format. • The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 7.4.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.4.17 Move Persons to Another Organization You can move the added persons to another organization if you need. Before You Start • Make sure you have added at least two organizations. • Make sure you have imported person information. Steps 1. Enter Person module. 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 2. Select the person you want to report card loss for and click Edit to open the Edit Person window. 3. In the Credential → Card panel, click on the added card to set this card as lost card. After reporting card loss, the access authorization of this card will be invalid and inactive. Other person who gets this card cannot access the doors by swiping this lost card. 4. Optional: If the lost card is found, you can click to cancel the loss.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E. If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should enable this function and select the sector of the card to encrypt.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note Up to 8 time duration(s) can be set for each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note You should configure the template before access group settings. Refer to Configure Schedule and Template for details. 5. In the left list of the Select Person field, select person(s) to assign access authority. 6. In the left list of the Select Access Point field, select door(s), door station(s) or floor(s) for the selected persons to access. 7. Click Save.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note You can check Display Failure Only to filter the applying results. The selected persons in the applied access groups will have the authorization to enter/exit the selected doors/door stations with their linked card(s). 9. Optional: Click to edit the access group if necessary. Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K5604A-3XF Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Enable CPU Card Reserved. If enable the function, the device can recognize the CPU card. You can present CPU card on the device. Enable ID Card Reserved. If enable the function, the device can recognize the ID card. You can present ID card on the device. 4. Click OK. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Name Edit the card reader name as desired. Minimum Card Swiping Interval If the interval between card swiping of the same card is less than the set value, the card swiping is invalid. You can set it as 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate when authentication. Application Mode You can select indoor or others application modes according to actual environment.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.7.2 Configure Remaining Open/Closed You can set the status of the door as open or closed. For example, you can set the door remaining closed in the holiday, and set the door remaining open in the specified period of the work day. Before You Start Add the access control devices to the system. Steps 1. Click Access Control → Advanced Function → Remain Open/Closed to enter the Remain Open/ Closed page. 2.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note Up to 8 time durations can be set to one holiday period. 5) Perform the following operations to edit the time durations. • Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to . • Click the time duration and directly edit the start/end time in the appeared dialog.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7) Optional: Select the person/card group(s), and then click Apply to re-apply access group that failed to be applied previously to the access control device. 4. Select an access control point (door) of selected device on the left panel. 5. Enter the maximum interval when entering password. 6. Add an authentication group for the selected access control point. 1) Click Add on the Authentication Groups panel.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note • The authentication times should be larger than 0 and smaller than the added personnel quantity in the personnel group. • The maximum value of authentication times is 16. 6) Click Save. Note • For each access control point (door), up to four authentication groups can be added. • For the authentication group of which authentication type is Local Authentication, up to 8 person/card groups can be added to the authentication group.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 7-9 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 7-10 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 7.7.5 Configure First Person In You can set multiple first persons for one access control point.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Note You can authenticate by the first person again to disable the first person mode. 4. Click Add on the First Person List panel. 5.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect. Example Set Card Swiping Path If you select Reader In_01 as the beginning, and select Reader In_02, Reader Out_04 as the linked card readers. Then you can only get through the access control point by swiping the card in the order as Reader In_01, Reader In_02 and Reader Out_04. 7.7.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Set Log Uploading Mode You can set the mode for the device to upload logs via ISUP protocol. Steps 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and enter Network → Uploading Mode . 4. Select the center group from the drop-down list. 5. Check Enable to enable to set the uploading mode. 6.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Set Device Capture Parameters You can configure the capture parameters of the access control device, including manual capture and event triggered capture. Note • The capture function should be supported by the device. • Before setting the capture parameters, you should set the picture storage first to define where the event triggered pictures are saved. For details, refer to Set Picture Storage in the user manual of the client software. .
DS-K5604A-3XF Series Face Recognition Terminal User Manual Before You Start Before setting the capture parameters, you should set the saving path first to define where the captured pictures are saved. For details, refer to Set Picture Storage in the user manual of the client software. Steps Note This function should be supported by the device 1. 2. 3. 4. 5. Enter the Access Control module. On the navigation bar on the left, enter Advanced Function → More Parameters → Capture .
DS-K5604A-3XF Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode (1:N) Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. ECO Mode Threshold When enabling the ECO mode, you can set the ECO mode's threshold.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Steps 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click RS-485 to enter the RS-485 Settings page. 4. Select the serial port number from the drop-down list to set the RS-485 parameters. 5. Set the baud rate, data bit, the stop bit, parity type, communication mode, working mode, and connection mode in the drop-down list.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.8 Configure Linkage Actions for Access Control You can configure different linkage actions for the event detected by the access control device. After that, linkage actions will be triggered once the event happens. This mechanism is used for notifying the security personnel the event, or triggering automatic access control in real time.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Send Email Send an email notification of the alarm information to one or more receivers. For details about setting email parameters, refer to Set Email Parameters in the user manual of client software.. 2) Click OK. 5. Enable the event so that when the event is detected, en event will be sent to the client and the linkage actions will be triggered. 6. Optional: Click Copy to...
DS-K5604A-3XF Series Face Recognition Terminal User Manual Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. 7.8.3 Configure Device Actions for Card Swiping You can set the access control device's linkage actions for the specified card swiping. When you swipe the specified card, it can trigger the host buzzer, and other actions on the same device. Steps Note It should be supported by the device. 1. 2. 3. 4. 5. 6. 7.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.8.4 Configure Device Actions for Person ID You can set the access control device's linkage actions for the specified person ID. When access control device detects the specified person ID, it can trigger buzzer on card reader, and other actions. Steps Note It should be supported by the device. 1. 2. 3. 4. 5. 6. 7. Click Access Control → Linkage Configuration . Select the access control device from the list on the left.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.9 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device. You can also control the doors such as open/close the door, or remain the door open/closed via the client remotely. The real-time access event are displayed in this module. You can view the access details and person details.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Capture Capture a picture manually. Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in the user manual of the client software. Result The icon of the doors will change in real-time according to the operation if the operation is succeeded. 7.9.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Before the client can receive the event information from the device, you need to enable the events of the resource and arm the device first. For details, refer to and Enable Receiving Event from Devices . 7.10.1 Enable Receiving Event from Devices Before the client software can receive event notifications from the device, you need to arm the device first. Steps 1. Click → Tool → Device Arming Control to open Device Arming Control page.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Priority Priority represents the emergency degree of the event. 2. Filter the events. Filter by Device Type and (or) Priority Select device type(s) and (or) priorities to filter events. Filter by Keywords Enter the keywords to filter the events. 3. Optional: Right-click the table header of the event list to customize the event related items to be displayed in the event list. 4. View the event details. 1) Select an event in the event list.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.10.3 Search Historical Events In the Event Search module of the event center page, you can search the historical events via time, device type, and other conditions according to the specified device type, and then process the events. Before You Start Enable receiving events from devices before the client can receive event information from the device,see Enable Receiving Event from Devices for details. Steps 1.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 7-12 Search Historical Events 4. Optional: Right click the table header of the event list to customize the event related items to be displayed in the event list. 5. Optional: Perform one of the following operations. Handle a Single Event Handle single event: Select one event that need to be processed, and then click Handle in the event information details page, and enter the processing suggestion.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Download Event Related Picture Hover the cursor on the related picture, and then click the download icon on the upper-right corner of the picture to download it to the local PC. You can set the saving path manually. 7.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Steps 1. Click Time & Attendance → Attendance Settings → Overtime . 2. Set required information. Overtime Level for Workday When you work for a certain period after end-work time on workday, you will reach different overtime level: overtime level 1, overtime level 2 and overtime level 3. You can set different work hour rate for three overtime levels, respectively.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Configure Holiday You can add the holiday during which the check-in or check-out will not be recorded. Add Regular Holiday You can configure a holiday which will take effect annually on regular days during the effective period, such as New Year's Day, Independence Day, Christmas Day, etc. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Holiday to enter the Holiday Settings page. 3. Check Regular Holiday as holiday type.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Example If you want to set the forth Thursday in November, 2019 as the Thanksgiving Day holiday, you should select 2019, November, 4th, and Thursday from the four drop-down lists. 7. Enter the number of the holiday days. 8. Set the attendance status if the employee works on holiday. 9. Optional: Check Repeat Annually to make this holiday setting effective every year 10. Click OK. The added holiday will display in the holiday list and calendar.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Synchronize Authentication Record to Third-Party Database The attendance data recorded in client software can be used by other system for calculation or some other operations. You can enable synchronization function to apply the authentication record from client software to the third-party database automatically. Steps 1. Enter Time & Attendance module. 2. Click Attendance Settings → Third-Party Database . 3.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Set the time when the break starts and ends. No Earlier Than / No Later Than Set the earliest swiping time for starting break and the latest swiping time for ending break. Break Duration The duration from start time to end time of the break. Calculation Auto Deduct The fixed break duration will be excluded from work hours. Must Check The break duration will be calculated and excluded from work hours according to actual check-in and check-out time.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.11.2 Add General Timetable On the timetable page, you can add general timetable for employees, which requires the fixed start-work time and end-work time. Also, you can set valid check-in/out time, allowable timetable for being late and leaving early. Steps 1. Click Time and Attendance → Timetable to enter the timetable settings page. 2. Click Add to enter add timetable page. Figure 7-13 Add Timetable 3. Create a name for the timetable.
DS-K5604A-3XF Series Face Recognition Terminal User Manual The first check-in time is recorded as start work time and the last check-out time is recorded as the end-work time. Each Check-In/Out Each check-in time and check-out time is valid and the sum of all periods between adjacent check-in and check-out time will be recorded as the valid working duration. You need to set Valid Authentication Interval for this calculation method.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 10. Optional: Perform one or more following operations after adding timetable. Edit Timetable Select a timetable from the list to edit related information. Delete Timetable Select a timetable from the list and click Delete to delete it. 7.11.3 Add Shift You can add shift for employees including setting shift period (day, week, month) and the effective attendance time.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note You can select more than one timetables. The start and end work time and the valid check-in and out time in different time tables can not be overlapped. Figure 7-15 Add Multiple Timetables 6. Click Save. The added shift lists on the left panel of the page. At most 64 shifts can be added. 7. Optional: Assign the shift to organization or person for a quick shift schedule. 1) Click Assign.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Effective for Overtime The persons' overtime will be recorded for this schedule. 5) Click Save to save the quick shift schedule. 7.11.4 Manage Shift Schedule Shift work is an employment practice designed to make use of all 24 hours of the clock each day of the week. The practice typically sees the day divided into shifts, set periods of time during which different shifts perform their duties.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 6. Set the start date and end date. 7. Set other parameters for the schedule. Check-in Not Required Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work. Scheduled on Holidays On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule.
DS-K5604A-3XF Series Face Recognition Terminal User Manual effective in any of the three timetables. If the person checks in at 07:50, it will apply the nearest timetable 08:00 to 15:00 to the person's attendance. 6. Set the start date and end date. 7. Set other parameters for the schedule. Check-in Not Required Persons in this schedule do not need to check-in when they come to work. Check-out Not Required Persons in this schedule do not need to check-out when they end work.
DS-K5604A-3XF Series Face Recognition Terminal User Manual It contains more than one timetables. The person can check in/out in any of the timetables and the attendance will be effective. If the multiple shift schedules contains three timetables: 00:00 to 07:00, 08:00 to 15:00 and 16:00 to 23:00. The attendance of the person adopting this multiple shift schedules will be effective in any of the three timetables.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 5. Set the check-in/out correction parameters. - Select Check-in and set the actual start-work time. - Select Check-out and set the actual end-work time. Note You can click supported. to add multiple check in/out items. At most 8 check-in/out items can be 6. Optional: Enter the remark information as desired. 7. Click Save. 8. Optional: After adding the check-in/out correction, perform one of the following operations. View Click or mode.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note You can set the leave type in Attendance Settings. For details, refer to Configure Leave Type . 6. 7. 8. 9. Set the time for leave. Optional: Enter the remark information as desired. Click Save. Optional: After adding the leave and business trip, perform one of the following operations. View Click or mode.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 3. In the Auto-Calculate Attendance area, set the time that you want the client to calculate the data. 4. Click Save. The client will calculate the attendance data of the previous day from the time you have configured. Manually Calculate Attendance Data You can calculate the attendance data manually by setting the data range. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Calculation . 3.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Before You Start • You should add organizations and persons in Person module and the persons have swiped cards. For details, refer to Person Management . • Calculate the attendance data. Note • The client will automatically calculate the previous day's attendance data at 1:00 am on the next day. • Keep the client running at 1:00 am or it cannot calculate the previous day's attendance data automatically.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 2. 3. 4. 5. Click Attendance Statistics → Report . Select a report type. Select the department or person to view the attendance report. Set the start time and end time during which the attendance data will be displayed in the report. 6. Click Report to generate the statistics report and open it.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Note Make sure the attendance records are calculated before the sending time. You can calculate the attendance data manually, or set the schedule so that the client can calculate the data automatically every day. For details, refer to Calculate Attendance Data . 5) Enter the receiver email address(es). Note You can click + to add a new email address. Up to 5 email addresses are allowed. 6) Optional: Click Preview to view the email details. 6.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Figure 7-16 View Device Information You can set the device name, view the device type, serial No., version, relay number, and lock number. Click Save to save the settings. 7.12.2 Change Device Password You can change the device password. Before You Start Make sure the device is activated. For details, see Activation. Steps 1. On the Device for Management page, click → System → User to enter the User tab. 2.
DS-K5604A-3XF Series Face Recognition Terminal User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 4.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.12.4 System Maintenance You can reboot the device remotely, restore the device to default settings, import configuration file, upgrade the device, etc. Reboot On the Device for Management page, click → System → System Maintenance to enter the System Maintenance tab. Click Reboot and the device starts rebooting.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Select a device type from the drop-down list, click Browse and select an upgrade file from the local computer, and click Upgrade. Note • If you select Card reader as the device type, you should also select a card reader No. from the drop-down list. • The upgrade will lasts for about 2 min. Do not power off during the upgrading. After upgrading, the device will reboot automatically. 7.12.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.12.7 Network Parameters Settings Set device network parameters, including the NIC type, DHCP, and HTTP. On the Device for Management page, click → Network → Network Parameters to enter the Network Parameters Settings tab. NIC Type Select a NIC type from the drop-down list. You can select either Self-adaptive, 10M, or 100M.
DS-K5604A-3XF Series Face Recognition Terminal User Manual After enabling the function, you can set the center's address type, IP address/domain name, port No., EHome user name, etc. Click Save. 7.12.10 Configure SIP Parameters Set the main station's IP address and the SIP server's IP address. After setting the parameters, you can communicate among the access control device, door station, indoor station, main station, and the platform.
DS-K5604A-3XF Series Face Recognition Terminal User Manual If you enable this function, the captured pictures will be saved. Temperature Measurement Only When enabling the function, the device will not authenticate the permissions, but only take the temperature. When disabling the function, the device will authenticate the permissions and at the same time take the temperature.
DS-K5604A-3XF Series Face Recognition Terminal User Manual ECO Mode After enabling the ECO mode, the device will use the IR camera to authenticate faces in the low light or dark environment. And you can set he ECO mode threshold, ECO mode (1:N), and ECO mode (1:1). ECO Mode (1:1) Set the matching threshold when authenticating via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Margin (Bottom) The distance percentage from the face bottom side to the bottom margin in the recognition area. The actual distance percentage should be larger than the configured value when face picture authentication. Other percentages, distances, and angles should also meet their conditions. Pupillary Distance The minimum resolution between two pupils when face recognition. The actual resolution should be larger than the configured value.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 7.12.17 Configure Video and Audio Parameters You can set the device camera's image quality, resolution and other parameters. Steps 1. Click Maintenance and Management → Device to enter the device list. 2. Click to enter the remote configuration page. 3. Click Image → Video & Audio to enter the settings page. 4.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. • Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function.
DS-K5604A-3XF Series Face Recognition Terminal User Manual 136
DS-K5604A-3XF Series Face Recognition Terminal User Manual Appendix B. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K5604A-3XF Series Face Recognition Terminal User Manual Appendix C.
UD19356B-B