Quick Start Guide

DS-KD8003-IME1
Video Intercom Module Door Staon
UD20199B-A
ENGLISH
Diagram References
1
Microphone
2
Built-in Camera
3
Loudspeaker
4
5
Nametag
6
TAMPER
7
Network Interface
8
Note: The module-connecng interface is used to connect other funcon module, such as nametag module,
keypad module, card reader module, etc. All these modules are known as sub module.
Appearance
1
Module-Connecng Interface
9
1
Low Illuminaon IR Supplement Light
Set Screw
10
Call Buon
Terminal
2
A1
A2
A3
A4
A5
A6
A7
A8
NC1: Door Lock Relay Output (NC)
NO1: Door Lock Relay Output (NO)
COM: Common Interface
NC2: Door Lock Relay Output (NC)
NO2: Door Lock Relay Output (NO)
GND: Grounding
12 VDC: Power Input
GND: Grounding
B1
B2
B3
B4
B5
B6
B7
B8
AIN2: For the access of Door Contact 2
AIN1: For the access of Door Contact 1
AIN3: For the access of Exit Buon 1
AIN4: For the access of Exit Buon 2
485-: Module-connecng Interface
485+: Module-connecng Interface
12V OUT: Module-connecng Interface
GND: Module-connecng Interface
C
PoE Network Interface (Supports IEEE 802.af/at-Compliant Devices)
Installaon
3
Note: Video intercom module door staon support one-module installaon, two-module installaon, three-
module installaon and more-than-three-module installaon. Here takes three-module installaon as an
example.
Tools that you need to prepare for installaon: Drill(6), cross screw driver (PH1*150
mm), and gradienter.
Make sure all the related equipment is power-off during the installaon.
Make sure you have configured the sub module address before installaon. Valid sub
module address range is 1 to 8. The No. should be unique for sub modules that
connected to the same main unit. The sub module address and corresponding switch
status is shown as the figure.
Before You Start
Three-Module Flush Mounng
1. Cave the installaon hole, and pull the cable out.
Note: The suggested dimension of the installaon hole is 321.8(W) × 108(H) × 45.5(D) mm. The suggested
length of the cables le outside is 270 mm.
2. Select a cable entry and remove the plasc sheet. Route the cables through the gang
box hole. Insert the gang box into the installaon hole. Mark the gang box screw holes’
posion with a marker, and take out the gang box.
3. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into
the screw holes. Fix the gang box with 4 expansion bolts.
4. Fill the gap between the gang box and wall with concrete or Silicone sealant. Remove
the mounng ears with tool aer concrete is dry.
5. Connect cables and insert the modules.
a.Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main
unit, then insert the main unit into the upper grid.
b.Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect
one end of Sub Module 1 and insert it into the middle grid.
c.Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it
into the boom grid.
6. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench.
Surface Mounng with Protecve Shield
1. Paste the installaon scker 1 onto the wall. Make sure the scker is placed
horizontally via measuring with the gradienter. Drill 4 holes according to the screw holes
on the scker.
Note: The suggested size of hole is 6(diameter) × 25(depth) mm. The suggested length of the cables le
outside is 270 mm.
2. Remove the scker and insert the expansion sleeves into the screw holes. Fix the
mounng frame
onto the wall with 4 expansion bolts.
3. Thread the module-connecng line across the thread holes of the frame. Pass the
main unit
connecng line across the thread hole to the top grid and connect the cables.
a.Connect the lines and module-connecng line 1 to the corresponding interfaces of
the main unit,
then place the main unit into the upper grid.
b.Connect the other end of the module-connecng line 1 to the input interface of the
sub modules via module-connecng line 2.
c.Organize the cables with cable e in the package.
4. Insert the modules into the frame aer wiring. The main unit must be placed in the
top grid.
5. Use the hexagon wrench in the package to fix the cover onto the frame.
Gang Box
1 2 3 4 5 6
13
1
2 3 4 5
Expansion Bolt
Mounng Ear
Main Unit
Sub Module 1
Sub Module 2
Hexagonal
Screw
1
2
2
2
1
3
3
3
Module-Connecng
Line1
Module-Connecng
Line2
Thread Hole
Cables Connected
to Main Module
Main Unit
Sub Module
Mounng Frame
Hexagonal
Screw
Cover
Hexagon Wrench
13
1
2
3
4
5
6
7
8
9 10
2
A1 A8 B8B1 C
LAN
GND 12V OUT 485+ 485-
AIN4
AIN3
AIN1
AIN2
GND GND 12V DC NC1 NC2 NO2 NO1 COM
RS485
ALARM IN
DOOR