Network Indoor Station Configuration Guide
Network Indoor Station Configuration Guide Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Network Indoor Station Configuration Guide CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Network Indoor Station Configuration Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Network Indoor Station Configuration Guide Contents 1 Local Operation .......................................................................................... 1 1.1 Activate Indoor Station ..................................................................................... 1 1.2 Configuration Settings ....................................................................................... 1 1.2.1 Set Indoor Station Network Parameters ................................................... 2 1.2.
Network Indoor Station Configuration Guide 2.2.2 Modify Network Information ................................................................. 19 2.3 System Configuration ...................................................................................... 20 2.4 Remote Configuration ..................................................................................... 20 2.4.1 System .................................................................................................... 20 2.4.
Network Indoor Station Configuration Guide 1 Local Operation 1.1 Activate Indoor Station You can only configure and operate the indoor station after creating a password for the device activation. Steps 1. Power on the device. It will enter the activation page automatically. Figure 1-1 Activation Page 2. Create a password and confirm it. 3. Tap OK to activate the indoor station.
Network Indoor Station Configuration Guide Configuration settings is required before starting using the indoor station. It is necessary to set the indoor station network, room No., linked devices, device time display, and so on. 1.2.1 Set Indoor Station Network Parameters Network connection is mandatory for the use of the indoor station. Set the network parameters after activating the indoor station.
Network Indoor Station Configuration Guide Linked network parameters refers to the network parameters of devices (like door station, doorphone, main station, center, etc.), to which the indoor station is linked. Linked devices for the indoor station refers to door station, center, main station, and doorphone. With the private SIP protocol, intercom can be realized only when all these devices are in the same network segment with the indoor station.
Network Indoor Station Configuration Guide Figure 1-4 Device Information Restore the door station via indoor station. Tap to restore the parameters of the door station. Modify the IP address of the linked door station. Tap to edit the IP address of door station. 5. Select the device to link. Edit the network parameters. 1.2.3 Set Indoor Station No. Indoor station No. and the indoor extension No.
Network Indoor Station Configuration Guide Figure 1-5 Set Indoor Station Information 3. Select Indoor Station Type from Indoor Station or Indoor Extension according to your actual needs. - Indoor Station: You can set the indoor station's room information, including the room name, community No., building No., Unit No., floor, and room No., the live view duration, the SIP register password, and the SIP parameters.
Network Indoor Station Configuration Guide 2) Enable Enable Standard SIP. 3) Tap VOIP Account Settings and configure the account information, including the user name, the phone number, the registered user name, the password, the domain, the port No,, and the expiration date. Note Up to 32 characters are allowed in the user name. 1.2.5 Add Camera Steps 1. Tap Settings → 2. Tap → Configuration , and enter admin (activation) password. to enter the device management page. 3. Tap + to pop up the dialog box.
Network Indoor Station Configuration Guide Figure 1-6 Zone Settings 2. Press a zone to pop up the zone editing dialogue box. 3. Set the zone type, alarm type, status of arming status, entering delay, and exiting delay. 4. Tap OK to save the settings. Note • 7 zone types are selectable: Panic Button, Door Magnetic, Smoke Detector, Active Infrared, Passive Infrared, Gas Detector, and Doorbell. • 3 alarm types are selectable: 24h Alarm, Instant Alarm, and Delay Alarm.
Network Indoor Station Configuration Guide Before You Start Tap Settings → → Shortcut Settings to enable Alarm. Steps Note On the home page, the arming status function and zone settings function are hidden by default. You should enable the alarm function first. 1. Back to the home page, tap Settings → mode settings page. → Scene Settings to enter the arming 2. Tap Stay Mode, Away Mode, Sleeping Mode, or Custom to enter the page. Figure 1-7 Arming Mode Settings 3. Arm the selected zone.
Network Indoor Station Configuration Guide You can create and edit the arm/disarm password, duress code and unlock password of the indoor station. Steps 1. Tap Settings → → Password to enter the password settings page. 2. Tap Arm/Disarm, Unlock or Duress Code to pop up the password settings dialog box. Arm/Disarm The password is for arming or disarming the zone for the indoor station. Note By default, the Arm/Disarm page is hidden. Tap Settings → → Shortcut Settings and enable Alarm.
Network Indoor Station Configuration Guide Figure 1-8 Time Synchronization 2. Enable Enable NTP. 3. Set the synchronizing interval, enter the IP address/domain of NTP server and port No., and select the time zone. Note • The default unit of synchronizing interval is minute. • The time zone can be configured as well if the NTP is not enabled. 1.5 Sound Settings Set the ringtone sound and the volume. 1.5.1 Call Settings You can set the ringtone, ring duration, call forwarding time on call settings page.
Network Indoor Station Configuration Guide Figure 1-9 Call Settings 2. Set corresponding parameters. Ringtone There are 3 ringtones by default, and you can custom and import at most 4 ringtones via Batch Configuration Tool or iVMS-4200 Client Software. Ringtone Duration: The maximum duration of indoor station when it is called without being accepted. Ringtone duration ranges from 30 s to 60 s.
Network Indoor Station Configuration Guide time duration. Within the configured time, this device will not be disturbed. Note Indoor extension does not support the ring duration settings, call forwarding settings, or auto-answer function. 1.5.2 Volume Settings Set the microphone volume, prompt sound volume, call volume, and enable touch sound. Steps 1. Tap Settings → → Volume Settings to enter the volume settings page. 2. Set the microphone volume, prompt sound volume, and the call volume.
Network Indoor Station Configuration Guide 4. Tap Restore All to restore all parameters and reboot the system. 1.8 System Maintenance You can format or install TF card, clear the screen, view the version information of the indoor station and reboot the system on the system maintenance page. Tap Settings → Password to enter the general settings page. Figure 1-11 General Settings Page Create the device unlock password and the duress code Unlock Create the indoor station's unlock password.
Network Indoor Station Configuration Guide Note • Make sure your device is connected with the network or the NTP function will not available. • For details, see Synchronize Time. System Language Tap System Language to change the system language. Note The indoor station supports 11 languages. Brightness Adjustment Tap + or - to adjust the screen brightness. Clean Screen Enable Clear Screen and the screen will be locked for 30s. And you can clear the screen within the time duration.
Network Indoor Station Configuration Guide Shortcut Settings Enable call elevator, alarm, call management center, or leave message and the icon will be displayed on the home page. Zone Settings Set the zone parameters. For details, see Zone Settings. Scene Settings Set the scene parameters, including the stay mode, the away mode, the sleeping mode, or customize the scene. For details, see Arming Mode Settings. 1.9 Device Information View the device information, including the version, model, serial No.
Network Indoor Station Configuration Guide 2 Remote Operation via the client software The Video Intercom module provides remote control and configuration on video intercom products via the iVMS-4200 client software. 2.1 Activate Device Remotely You can only configure and operate the indoor station after creating a password for the device activation. Before You Start Default parameters of indoor station are as follows: • Default IP Address: 192.0.0.64. • Default Port No.: 8000.
Network Indoor Station Configuration Guide Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 2.2.1 Add Video Intercom Devices Steps Note • You can add at most 512 indoor stations and main stations in total to the client, and add at most 16 door stations to the client.
Network Indoor Station Configuration Guide Figure 2-1 Add the Device 4. Optional: Click Online Device, the active online devices in the same local subnet with the client software will be displayed on the Online Device area. Note To add online devices to the software, you are required to change the device IP address to the same subnet with your computer first. 1) You can click Refresh Every 60s to refresh the information of the online devices. 2) Select the devices to be added from the list.
Network Indoor Station Configuration Guide Edit a name for the device as you want. Address Input the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port Input the device port No. The default value is 8000. User Name Input the device user name. By default, the user name is admin. Password Input the device password. By default, the password is 12345. 6. Optional: You can check the checkbox Export to Group to create a group by the device name.
Network Indoor Station Configuration Guide 2.3 System Configuration You can configure the video intercom parameters accordingly. Steps 1. Click Maintenance and Management → System Configuration → Acs and videoIntercom to enter the system configuration page. 2. Enter the required information. Ringtone Click ... and select the audio file from the local path for the ringtone of indoor station. Optionally, you can click for a testing of the audio file. Max.
Network Indoor Station Configuration Guide Device Information Click Device Information to enter device basic information page. You can view basic information (the device type, and serial No.), and version information of the device. Figure 2-2 Device Information General Click General to enter device general parameters settings page. You can view and edit the device name and device ID. Figure 2-3 General Time Click Time to enter the device time settings page.
Network Indoor Station Configuration Guide Figure 2-4 Synchronize Time Select Time Zone or Enable NTP. Click Save to save the time settings. • Time Zone • Select a time zone from the drop-down list menu. • Click Synchronization. • NTP • Check the checkbox of Enable NTP to enable NTP. • Enter the server address, NTP port, and synchronization interval. Note The default port No. is 123. System Maintenance Click System Maintenance to enter the page.
Network Indoor Station Configuration Guide Figure 2-5 System Maintenance • Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the system. • Click Restore Default Settings to restore the default parameters. • Click Restore All to restore all parameters of device and reset the device to inactive status. Note • Click Restore Default Settings, all default settings, excluding network parameters, will be restored.
Network Indoor Station Configuration Guide • Click ... to select the upgrade file and click Upgrade to remote upgrade the device. The process of remote upgrade will be displayed in the process bar. • Select a language, and click Save to change the device system language. Note • The device supports 11 languages: English, Russian, German, Italian, French, Portuguese, Spanish, Turkish, Arabic, Polish, and Vietnamese. • Rebooting the device is required after you change the system language.
Network Indoor Station Configuration Guide RS-485 Click RS485 to enter the RS-485 settings page. You can view and edit the RS-485 parameters of the device. Figure 2-7 RS-485 Settings Note For indoor station and main station, there are 3 choices for the working mode: transparent channel, disable, and custom. 2.4.
Network Indoor Station Configuration Guide Figure 2-8 ID Configuration 2. Select the device type from the drop-down list, and set the corresponding information. 3. Click Save to enable the device number configuration. Time Parameters Steps 1. Click Time Parameters to enter time parameters settings page. Figure 2-9 Time Parameters 2. Configure the maximum ring duration, maximum live view time, and call forwarding time. 3. Click Save.
Network Indoor Station Configuration Guide • Call forwarding time refers to the ring duration limit beyond which the call is automatically forwarded to the mobile phone designated by the resident. The range of call forwarding time varies from 0s to 20s. • For indoor extension, it only requires setting the maximum live view time. Permission Password Click Permission Password to enter password changing page. Figure 2-10 Permission Password For indoor station, you can change the arm/disarm password.
Network Indoor Station Configuration Guide Figure 2-11 Zone Alarm 2. Select Zone No. 3. Select Zone Type. 4. Select Alarm Type. 5. Set the NO/NC status. 6. Set Entering Delay and Exiting Delay. 7. Select triggers. 8. Click Save to enable zone settings. Note • 7 zone types are supported: Emergency Switch, Door Magnetic Switch, Smoke Detector, Active IR Detector, Passive IR Detector, Combustible Gas Detector, and DoorBell Switch.
Network Indoor Station Configuration Guide • When the zone type is set to be Delay Alarm, only under arming mode, the indoor station will receive alarm message when the detector is triggered. Under disarming mode, it will not receive alarm message when the detector is triggered.
Network Indoor Station Configuration Guide Steps 1. Click Export to export the added device information file. 2. Edit parameters of added devices in batch in the exported file. 3. Click Import to pop up importing box, and open the edited added device information file. Figure 2-13 Import Added Device Information Volume Input and Output Steps 1. Click Volume Input/Output to enter the volume input and output page. Figure 2-14 Volume Input and Output 2.
Network Indoor Station Configuration Guide Ring Import Steps 1. Click Ring Import to enter the ring configuration page. Figure 2-15 Ring Import 2. Click + to add the ring, and click x to delete the imported ring. Note • The ring to be imported should be in the wav format, and the size of the ring cannot be larger than 300k. • Up to 4 rings can be added. Deploy Info Click Deploy Info, you can get the deploy informations. Figure 2-16 Deploy Info Incoming Call Linkage Steps 1.
Network Indoor Station Configuration Guide Figure 2-17 Incoming Call Linkage 2. Enable and select triggers. When the calling incoming, the alarm you linked will be triggered. Relay Click Relay. Select a relay and click " time. Click Save to save the settings. " and set the relay name and output delay 2.4.3 Network Local Network Configuration Steps 1. Click Local Network Configuration to enter local network configuration page. Figure 2-18 Local Network Configuration 2.
Network Indoor Station Configuration Guide Note • The default port No. is 8000. • After editing the local network parameters of device, you should add the devices to the device list again. Linked Devices Network Configuration In the linked devices network configuration page, you can configure the network parameters of main stations, SIP servers and management centers of the same LAN. The devices can be linked to the door station and realize the linkage between these devices. Steps 1.
Network Indoor Station Configuration Guide Click Advanced Settings to enter DNS address settings page. Edit the IP address and click Save. Figure 2-19 DNS Settings Configure Mobile Client Connection Configure Hik-Connect server parameters before viewing videos via mobile client. Before You Start Make sure the indoor station connects to the network. Steps 1. Click Hik-Connect to enter configuration page. 2. Enable Enable Hik-Connect Access. 3. Enable Custom and edit Service Address 4.
Network Indoor Station Configuration Guide Figure 2-20 Personal Management Application The page is divided into two parts: Organization Management and Person Management. Organization Management You can add, edit, or delete the organization as desired. Person Management After adding the organization, you can add the person to the organization and issue card to persons for further management. 2.5.
Network Indoor Station Configuration Guide Note Up to 10 levels of organizations can be created. Modify and Delete Organization You can select the added organization and click to modify its name. You can select an organization, and click X button to delete it. Note • The lower-level organizations will be deleted as well if you delete an organization. • Make sure there is no person added under the organization, or the organization cannot be deleted. 2.5.
Network Indoor Station Configuration Guide 2) Optional: Click Add Face to upload the photo. Note The picture should be in *.jpg format. Click Upload Select the person picture from the local PC to upload it to the client. Click Take Phone Take the person's photo with the PC camera. Click Remote Collection Take the person's photo with the collection device. 3. Issue the card for the person. 1) Click Credential → Card . 2) Click + to pop up the Add Card dialog. 3) Select Normal Card as Card Type.
Network Indoor Station Configuration Guide 4) Click OK to start exporting. 2. Importing Person: You can import the Excel file with persons information in batch from the local PC. 1) Click Import Person. 2) You can click Download Template for Importing Person to download the template first. 3) Input the person information to the downloaded template. 4) Click ... to select the Excel file with person information. 5) Click OK to start importing.
Network Indoor Station Configuration Guide Select the person and click Edit to open the editing person dialog. To delete the person, select a person and click Delete to delete it. Note If a card is issued to the current person, the linkage will be invalid after the person is deleted. Change Person to Other Organization You can move the person to another organization if needed. Steps 1. Select the person in the list and click Change Organization. 2. Select the organization to move the person to. 3.
Network Indoor Station Configuration Guide A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD20191B