Quick Start Guide
1
DS-KH8520-WTE1
Network Indoor Staon UD20187B
3
4
Screen
1
Screen Microphone
2
Debugging Port
3
TF Card Slot
4
Alarm Terminal
5
Power Terminal
6
Network Interface
7
Loudspeaker
8
Note:
The appearance of the device varies according to different models. Refers to the actual device for detailed
informaon.
The debugging port is used for debugging only.
Terminal and Wiring
2
There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485 pins, 5
reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.
Installaon
3
It supports wall mounng. There are two installaon modes.
ENGLISH
Diagram References
Appearance
1
Installaon Accessory Descripon
The wall mounng plate and juncon box are required to install the indoor staon onto
the wall.
The dimension of juncon box should be 75 mm (width) 75 mm (length) 50 mm × ×
(depth). The dimension of wall mounng plate is shown.
Wall Mounng with juncon Box
Make sure the device in the package is in good condion and all the assembly parts
are included.
The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
Make sure all related equipments are power-off during the installaon.
Check the product specificaon for the installaon environment.
Before You Start
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock catch
will be locked automacally.
11
3
Geng Started
4
You are required to acvate the device first by sengs a strong password before you
can use the device.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
Acvate Indoor Staon
1
Quick Configuraon
2
Refers to Video Intercom Network Indoor Staon Configuraon Guide (Scan the QR code) for details.
Refers to Video Intercom Network Indoor Staon Operaon Guide (Scan the QR code) for details.
5
6
7
8
1
2
Wall Mounng without juncon Box
1. Insert 2 expansion tubes into the wall.
2. Fix the wall mounng plate to the juncon box with 2 screws.
3. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock catch
will be locked automacally.
3
Rear Panel (without Interface)
Lock Catch Lock Catch
Lock Catch
Lock Catch
Hook
Hook
Hook
Hook
Screw
Wall Mounng Plate Wall
Rear Panel (without Interface)
Lock Catch Lock Catch
Lock Catch
Lock Catch
Hook
Hook
Hook
Hook
Screw
Wall Mounng Plate Juncon Box Wall
Scan the QR code to get the
Operaon Guide for detailed
informaon.
Scan the QR code to get the
Configuraon Guide for detailed
informaon.
122
Unit:mm
100
64.85
RS-485
Reserved
2
Relay Output
Alarm
Input
Device
RS-485+
RS-485-
RES
RES
RES
RES
RES
NO2
NO1
COM1
COM2
AIN7
AIN6
AIN5
AIN4
AIN3
AIN2
AIN1
GND
AIN8
Red
Red
Blue
Green
Yellow
Yellow
White
Black
Red
Black
Black
Black
Black
White
White
White
White
White
White
White
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon parameters.
- .Select Indoor Staon and tap Next to link main door staon.
a. Edit Floor and Room No.
b. Create and confirm SIP register password.
Note: If you want to add the indoor staon to the door staon, the SIP password of the indoor staon
should be the same as the registraon password of the door staon.
c. Tap Advanced Sengs to edit Community No, Building No. and Unit No.
d. Oponal: Enable Indoor Staon Sengs and select the indoor staon to link.
- . Select Indoor Extension and tap Next to link indoor staon.
a. Edit No., Room Name.
b. Create and confirm SIP register password.
4. Linked related devices and tap Next. If the device and the indoor staon are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the sengs icon to pop up the Network Sengs page.
b. Edit the network parameters of the door staon manually or enable DHCP to get
the network parameters automacally.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.