Video Intercom Master Station User Manual UD02932B
Video Intercom Master Station·User Manual User Manual © 2016 Hangzhou Hikvision Digital Technology Co., Ltd. This user manual is intended for users of DS-KM8301 Video Intercom Master Station. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd.
Video Intercom Master Station·User Manual Support Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Master Station·User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Master Station·User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Video Intercom Master Station·User Manual Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Video Intercom Master Station·User Manual Contents 1 Overview ...................................................................................................... 2 1.1 Appearance of DS-KM8301 Model .......................................................................... 2 1.2 Typical Application ................................................................................................... 4 1.3 Terminals and Interfaces ..............................................................................
Video Intercom Master Station·User Manual 5.1 System Configuration............................................................................................. 42 5.2 Device Management.............................................................................................. 43 5.2.1 Adding Video Intercom Devices ...................................................................... 43 5.2.2 Modifying Network Information ..................................................................... 45 5.2.
Video Intercom Master Station·User Manual 1 Overview The DS-KM8301 master station is an intelligent terminal for video intercom system management. It responses and sends the residents call, receives alarm, and unlocks door remotely. It is normally installed on the management center, it can be operated with a capacitive touch screen, touch buttons and mechanical buttons.
Video Intercom Master Station·User Manual Table 1-1 Descriptions No.
Video Intercom Master Station·User Manual 1.
Video Intercom Master Station·User Manual Table 1-2 Descriptions of Terminals and Interfaces Name No.
Video Intercom Master Station·User Manual 2 Before You Start For the first time use of the device, you are required to activate the device and set the device password. You can activate the device locally or remotely via internet with Batch Configuration Tool, or with iVMS-4200 client software. To remotely activate the device with Batch Configuration Tool or iVMS-4200, refer to Chapter 4, and Chapter 5.
Video Intercom Master Station·User Manual 3 Local Operation 3.1 Activating Device Connect the power cable to power on the master station. You must create a password to activate the master station for your first time usage and when it is not activated. Only after activating the device, you can operate it both locally and remotely. The password created for the activation is only used when you add the station to the remote control software such as iVMS-4200.
Video Intercom Master Station·User Manual Figure 3-2 User Interface 3.3 Status Icon Definition Description Normal Status. The connection between master station and indoor/door stations is normal, and the master station has successfully registered to the SIP server. The master station is offline. Please check the network cable of the master station. Invalid SIP server IP address. Set the SIP server IP address. The master station has not registered to the SIP server.
Video Intercom Master Station·User Manual 3.4 Configuration Settings Purpose: You can set and view the local information, configure the network, manage devices, synchronize the device time, and restore the default settings. You can get to the configuration interface: Settings -> Configuration. 3.4.
Video Intercom Master Station·User Manual Figure 3-3 Local Information Settings 3.4.3 Setting Network Make sure the network cable is well-connected. Purpose: The connection of the network is mandatory for the use of the master station. Steps: 1. Get to the configuration interface: Settings -> Configuration, and enter the admin password (configuration password). 2. Press the Network tab to enter the network settings interface. Figure 3-4 Network Settings Interface 3.
Video Intercom Master Station·User Manual Figure 3-5 Setting Network 4. Enter a local IP address, subnet mask, and gateway. 5. Press the Save tab. Enable DHCP function to obtain an IP address automatically. 3.4.4 SIP (Session Initiation Protocol) Server Management The master station can work as a management center and SIP server simultaneously.
Video Intercom Master Station·User Manual Figure 3-6 SIP Server Adding 3. Enter the IP address of the SIP server. 4. Press the Save button to save the SIP server added. 3.4.5 Adding Devices Purpose: The master station never works alone. You can connect the door station, outer door station, IP camera, DVR, DVS, and NVR. Once connected, those devices can work together as a whole video intercom system.
Video Intercom Master Station·User Manual Figure 3-7 Device Management Adding the Door Station or Outer Door Station Steps: 1. Press the Add Device tab to pop up the Select Device Type dialogue box. Figure 3-8 Device Type Selecting 2. Select Door Station or Outer Door Station. 3. Enter the corresponding device information required on the pop-up device adding dialogue box.
Video Intercom Master Station·User Manual Figure 3-9 Door Station Adding 4. Press the Figure 3-10 Outer Door Station Adding tab on the upper left corner of the dialogue box. When the door station being added, the device name, IP address, project number, community number, building number, and serial number need to be entered. When the outer door station being added, the device name, IP address, project number, and serial number need to be entered.
Video Intercom Master Station·User Manual The default Port No. is 554, the default user name is admin. The port No. should be consistent with the RTSP (Real Time Streaming Protocol) port No. of the IP camera. When the IP camera added successfully, you can get the live view of IP camera on the live view interface. Adding DVR/DVS/NVR Steps: 1. Press the Add Device tab to pop up the Select Device Type dialogue box. 2. Select DVR/DVS/NVR. 3.
Video Intercom Master Station·User Manual 4. Set the synchronizing interval, enter the IP address of NTP server and port No., and select the time zone. The unit of synchronizing interval is minute, and the default port No. is 123. Figure 3-13 Time Synchronizing 3.4.7 Restoring Default Settings Steps: 1. Get to the configuration interface: Settings -> Configuration, and enter the admin password (configuration password). 2. Press the Restore tab. 3.
Video Intercom Master Station·User Manual 3.5 Video Call Settings 3.5.1 Callling Resident Steps: 1. Press the tab on the touch screen to enter the residents calling interface. 2. Enter the corresponding residents’ Room No.. 3. Press the tab to start a video intercom call. 4. Press the tab to stop the video intercom call. The room No. format should be like 1-1-1-102 as Community 1, Building 1, Unit 1, and Room 102. The community No. can be omitted.
Video Intercom Master Station·User Manual 3. Press the tab to start a video intercom call. 4. Press the tab to stop the video intercom call. The master station No. format should be like 1-51 as Community 1, No. 51. The community No. can be omitted. Switch to on the upper right corner to enable the camera function. Figure 3-16 Calling Master Station Interface 3.5.3 Adding Resident Information Steps: 1. Press the tab on the touch screen to enter the contact list interface. 2.
Video Intercom Master Station·User Manual Figure 3-17 Call Log Interface Hold down a piece of call log to open the call log handling menu. Press the Call tab to call back. Press the Delete tab to delete the piece of call log. Press the Clear tab to delete all pieces of call logs. When there is any missed call, the number of missed call will display on the tab as a prompt, e.g. the icon means there is 1 missed call. 3.
Video Intercom Master Station·User Manual Press the New Message tab on the user interface to view alarm messages of indoor/door stations. Figure 3-18 Alarm Log Interface Hold down a piece of alarm message to open the alarm message handling menu. Press the Ignore tab to ignore the piece of alarm message. Press the Live View tab to enter the live view interface. Press the Delete tab to delete the piece of alarm message. Press the Clear tab to delete all pieces of alarm messages.
Video Intercom Master Station·User Manual 1. Press the interface. tab on the touch screen to enter the Live View Figure 3-19 Live View Interface 2. Press the Door Station tab and press the door station device to view the live view of the corresponding door station. Figure 3-20 Live View of Door Station 3. Press the IP Camera tab and press the IPC device to view the live view of the corresponding IPC.
Video Intercom Master Station·User Manual Figure 3-21 Live View of IPC 22
Video Intercom Master Station·User Manual 4 Remote Configuration via Batch Configuration Tool You can configure and operate the video intercom devices via Batch Configuration Tool. Default parameters of master station are as follows: Default IP Address: 192.0.0.64. Default Port No.: 8000. Default User Name: admin. 4.1 Activating Device Remotely Purpose You are required to activate the device first by setting a strong password for it before you can use the device.
Video Intercom Master Station·User Manual 3. Create a password, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
Video Intercom Master Station·User Manual Figure 4-4 Editing Network Parameters The default port No. is 8000. The default IP address of the master station is 192.0.0.64. After editing the network parameters of device, you should add the devices to the device list again. Enable DHCP, and the software can obtain network parameters for the device automatically. 4.3 Adding Device Before you start: Make sure the device to be added has been activated.
Video Intercom Master Station·User Manual Figure 4-5 Online Devices Interface 2. Click the button to pop up the login dialog box. Figure 4-6 Login Dialog Box 3. Enter the user name and password. 4. Click the OK button to save the settings. Only devices successfully logged in will be added to the device list for configuration. If you add devices in batch, please make sure selected devices have the same user name and password. 4.3.
Video Intercom Master Station·User Manual Figure 4-8 Adding by IP Address 4. Click the OK button to add the device to the device list. You cannot add the device(s) to the device list if the user name and password are not identical. When you add devices by IP Address, or IP Segment, the devices should be online devices. 4.3.3 Adding by IP Segment Purpose: You can add many devices at once whose IP addresses are among the IP segment. Steps: 1. Click the button to pop up the adding devices dialog box.
Video Intercom Master Station·User Manual Figure 4-10 Adding by IP Segment 5. Click the OK button to search and add the devices whose IP addresses are within the range of the defined IP segment to the device list. 4.4 Configuring Devices Remotely In the device list area, select a device and click the remote configuration interface. or to enter Figure 4-11 Remote Configuration 4.4.
Video Intercom Master Station·User Manual General Click the General button to enter device general parameters settings interface. You can view and edit the device name and device ID. Figure 4-13 General Time Steps: 1. Click the Time button to enter the device time settings interface. Figure 4-14 Time Settings 2. Select Time Zone or Enable NTP. Time Zone 1) Select a time zone from the drop-down list menu. 2) Click the Synchronization button. NTP 1) Check the checkbox of Enable NTP to enable NTP.
Video Intercom Master Station·User Manual The default port No. is 123. System Maintenance Purpose: You can operate the system management and remote upgrading on the system maintenance interface. Steps: 1. Click the System Maintenance button to enter the system maintenance interface. Figure 4-15 System Maintenance 2. Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the system. 3. Click Restore Default Settings to restore the default parameters. 4.
Video Intercom Master Station·User Manual Figure 4-16 Import File 6. Click Export Configuration File and the export file window pops up. Select the saving path of remote configuration files and click Save to export the configuration file. Figure 4-17 Export File 7. Click to select the upgrade file and click Upgrade to remote upgrade the device. The process of remote upgrade will be displayed in the process bar.
Video Intercom Master Station·User Manual Click Restore Default Settings button, all default settings, excluding network parameters, will be restored. Click Restore All button, all default settings, including network parameters, will be restored. The device will be reset to inactivated status. User Purpose: You can edit the password for logging in the device. Steps: 1. Click the User button to enter the user information editing interface. Figure 4-19 Select User Name 2.
Video Intercom Master Station·User Manual After editing the password of device, click button from the device list, the added device will not be there. You should add the device again with new password to operate the remote configuration. RS485 Click the RS485 button to enter the RS485 setting interface. You can view and edit the RS485 parameters of the device. Figure 4-21 RS-485 For indoor station and master station, there are 3 choices for the working mode: transparent channel, disable, and custom. 4.
Video Intercom Master Station·User Manual Time Parameters 1. Click the Time Parameters button to enter time parameters settings interface. 2. Configure the maximum ring duration, maximum live view time, and maximum speaking time. 3. Click the Apply button. Figure 4-23 Time Parameters Maximum ring duration is the maximum duration of master station when it is called without being received. The range of maximum ring duration varies from 30s to 60s.
Video Intercom Master Station·User Manual Figure 4-25 Volume Configuration IP Camera Information Purpose: You can add, delete and modify devices that can be added to the master station, such as IP cameras, door stations, outer door stations, and DVR/NVR/DVS. By exporting and importing the added device information, you can edit added devices parameters in batch. Adding IP Camera, DVR/NVR/DVS, Door Station and Outer door Station Steps: 1.
Video Intercom Master Station·User Manual 1. Click the Export button to export the added device information file. Figure 4-28 Export Information 2. Edit parameters of added devices in batch in the exported file. 3. Click the Import button to pop up importing box, and open the edited added device information file. Figure 4-29 Import Information 4.4.3 Network Local Network Configuration Steps: 1. Click the Local Network Configuration button to enter local network configuration interface.
Video Intercom Master Station·User Manual Figure 4-30 Local Network Parameters 2. Enter the local IP address, subnet mask, gateway address, and port No.. 3. Click the Save button to enable the settings. The default port No. is 8000. After editing the local network parameters of device, you should add the devices to the device list again.
Video Intercom Master Station·User Manual Figure 4-32 Batch Upgrading 4.5.1 Adding Devices for Upgrading You should add the device to the batch upgrading tool first before upgrading the device. There are 2 ways to add the device: adding online device, and adding by IP address/IP segment. Adding Online Device Steps: 1. In the batch upgrading interface, click the window.
Video Intercom Master Station·User Manual Figure 4-33 Login 2. Select a device, enter the user name and password, and click the Login Device button. 3. Click the Add Device button, and the device is added to the batch upgrading tool.
Video Intercom Master Station·User Manual Adding by IP Address/IP Segment Steps: 1. Click the Manual button to open the device adding window. 2. Enter the corresponding information (IP address, user name, password, start IP address, end IP address). 3. Click the Add button. Figure 4-35 Adding by IP Address/IP Segment 4.5.2 Upgrading Devices There are 2 upgrading modes available: upgrading by file, and online upgrading.
Video Intercom Master Station·User Manual Figure 4-36 Upgrade by File 3. Open the upgrading file, and click the Upgrade button. Online Upgrading Online Upgrading: The batch upgrading tool will search the latest upgrading file for the device automatically. You upgrade the device or devices via the local upgrade files. Steps: 1. Select a device or multiple devices, and select “Online Upgrading” as the upgrading mode. 2. Click the Download button.
Video Intercom Master Station·User Manual 5 Remote Operation via iVMS-4200 5.1 System Configuration Purpose: You can configure the video intercom parameters accordingly. Steps: 1. Open the System Configuration page. Path: Control Panel -> Maintenance and Management -> System Configuration -> Video Intercom. 2. Click the Video Intercom tab to enter the Video Intercom Settings interface. 3. Input the required information.
Video Intercom Master Station·User Manual 5.2 Device Management Purpose: Device management includes device activation, adding device, editing device, and deleting device, and so on. After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 5.2.1 Adding Video Intercom Devices You can add at most 512 indoor stations and master stations in total to the iVMS-4200, and add at most 16 door stations to the iVMS-4200.
Video Intercom Master Station·User Manual 2) In the Server tab, Video Intercom Device will display, select Video Intercom Device and add indoor station and master station. To add door station: In the Server tab, select Encoding Device/Outdoor Device and add door station. 3. The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click the Refresh Every 60s button to refresh the information of the online devices.
Video Intercom Master Station·User Manual Figure 5-4 Adding Device by IP/Domain Add Multiple Online Devices If you want to add multiple online devices to the client software, click and hold Ctrl key to select multiple devices, and click Add to Client to open the device adding dialog box. In the pop-up message box, enter the user name and password for the devices to be added.
Video Intercom Master Station·User Manual Figure 5-5 Modifying Network Information You should enter the admin password of the device in the Password field of the pop-up window to modify the parameters. 5.2.3 Resetting Password According to the different video intercom devices, the software provides two different methods for restoring the default password or resetting the password. Select the device from the online device list, click Reset Password.
Video Intercom Master Station·User Manual Figure 5-6 Resetting Password (Option 1) 1. Click Export to save the device file on your computer. 2. Send the file to our technical engineers. 3. Our technical engineer will send a file to you. After receiving a file from the technical engineer, select Import File from Key Importing Mode drop-down list and click import the file. 4. Input new password in text fields of Password and Confirm Password. 5. Click OK to reset the password.
Video Intercom Master Station·User Manual Figure 5-7 Resetting Password (Option 2) 1. Click Export to save the device file on your computer. 2. Send the file to our technical engineers. 3. Click Import and select the file received from the technical engineer. 4. Input new password in text fields of Password and Confirm Password. 5. Click OK to reset the password.
Video Intercom Master Station·User Manual Figure 5-8 Tool Menu 2. Set the arming status of the device as armed, and the alarm information will be auto uploaded to the client software when alarm occurs. Figure 5-9 Device Arming Control Figure 5-10 Alarm Events After adding the device to the client software, it will be armed automatically.
Video Intercom Master Station·User Manual Appendix Wiring Cables Cables Specification Power Cable RVV 2*1.0 Network Cable Cat5e Warning To avoid echo and whistles, set the wire distance longer than 8 meters.
Video Intercom Master Station·User Manual 51
