ECI-D14F2 • ECI-D14F4 • ECI-D14F6 Network Dome Camera Quick Start Guide
ECI-D14Fx Network Dome Camera Quick Start Guide Manual Illustrations and Features Graphics (screen shots, product pictures, etc.) in this document are for illustrative purposes only. Your actual product may differ in appearance. Your product might not support all features discussed in this document. Hikvision USA Inc., 18639 Railroad St.
ECI-D14Fx Network Dome Camera Quick Start Guide CONFORMS TO THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ECI-D14Fx Network Dome Camera Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
ECI-D14Fx Network Dome Camera Quick Start Guide ● Cautions Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright locations.
ECI-D14Fx Network Dome Camera Quick Start Guide Contents 1 Appearance 6 2 Installation 6 3 Network Camera LAN Configuration 9 3.1 Wiring ........................................................................................................................ 9 3.2 Activate the Camera ................................................................................................ 10 3.2.1 Activation via Web Browser............................................................................ 10 3.2.
ECI-D14Fx Network Dome Camera Quick Start Guide 1 Appearance The appearance of this network dome camera is shown in figure 1-1. 1 4 2 5 6 7 3 8 Figure 1-1 Camera Overview Table 1-1 Description of Camera No.
ECI-D14Fx Network Dome Camera Quick Start Guide ● The standard power supply is 12 VDC. Make sure your power supply matches that of your camera. ● Make sure that all of the related equipment is powered off during installation. ● Check product specifications for the installation environment. ● Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket.
ECI-D14Fx Network Dome Camera Quick Start Guide Figure 2-2 Remove the Bubble 4. Fix the mounting base onto the ceiling with the supplied screws. Figure 2-3 Fix the Mounting Base 5. Route the cables through the cable hole. Note: If required, you can route cables through the side opening on the side of the mounting base. Side Opening Figure 2-4 Side Opening 6. Connect the corresponding cables, such as the power and network cables. 7.
ECI-D14Fx Network Dome Camera Quick Start Guide P: 0° to 355° T: 0° to 75° Tilt Adjusting Screw Figure 2-5 Camera 2-Axis Adjustment 1) Loosen the tilt adjusting screw to adjust the tilt angle [0° to 75°]. 2) Hold the black liner to adjust the pan angle [0°to 355°]. 8. Reinstall the bubble and tighten the screws. Figure 2-6 Bubble Reinstallation 3 Network Camera LAN Configuration Note: The use of products with internet access carries inherent security risks.
ECI-D14Fx Network Dome Camera Quick Start Guide 3.2 Activate the Camera Activate the camera by setting a strong password. Activation via Web browser, activation via SADP, and activation via client software are supported. Activation via SADP software and Web browser will be used as examples to introduce camera activation. Note: Refer to the network camera user manual for activation via client software. 3.2.1 Activation via Web Browser Steps: 1. Power the camera on.
ECI-D14Fx Network Dome Camera Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting online devices, activating cameras, and resetting passwords. SADP can be obtained from the supplied disk or the official website, and installed by following the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device.
ECI-D14Fx Network Dome Camera Quick Start Guide 3.3 Modify the IP Address Purpose: To view and configure the camera via the LAN (Local Area Network), connect the network camera to the same subnet as your PC. Use the SADP software or client software to search and change the IP address of the device. IP Address modification via SADP software will be used as an example. In order to modify the IP address via client software, refer to the user manual of the client software. Steps: 1. Run SADP. 2.
ECI-D14Fx Network Dome Camera Quick Start Guide Web Browser: Internet Explorer 8.0 or higher, Apple Safari 5.0.2 or higher, Mozilla Firefox 5.0 or higher, or Google Chrome 18 or higher Steps: 1. Open the Web browser. 2. In the browser address bar, input the IP address of the network camera, and press the Enter key to display the login interface. Note: The default IP address is 192.168.1.64. It is suggested that you change the IP address to the same subnet as your computer. 3.
ECI-D14Fx Network Dome Camera Quick Start Guide 5 Hik-Connect Purpose: Hik-Connect is a mobile application to view live camera images, receive alarm notifications, etc. 5.1 Enable Hik-Connect for Use with Cameras Purpose: Enable Hik-Connect should on your camera before using the service. You can enable the service either via SADP software or a Web browser. 5.2 Enable Hik-Connect Service via SADP Software Steps: 1. Check the Enable Hik-Connect checkbox: 1).
ECI-D14Fx Network Dome Camera Quick Start Guide 5.2.1 Enable Hik-Connect via a Web Browser Before You Start: Activate the camera before enabling the service. Refer to Chapter 3.2. for more information. Steps: 1. Access the camera via the Web browser. Refer to Chapter 4. 2. Enter the platform access configuration interface, as follows: Configuration > Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Set the Platform Access Mode to Hik-Connect. 4.
ECI-D14Fx Network Dome Camera Quick Start Guide Figure 5-3 Connect a Router Note: After the camera connects to the network, wait one minute before using the camera with Hik-Connect. 2. Add the camera to the Hik-Connect app: • If Accessing the Camera through an NVR: Tap “+” on the upper-right corner and scan the QR code that appears in the NVR interface. • If Accessing the Camera through a Web Browser: Tap the camera’s serial number. icon and type in the 3. Input your camera’s verification code.
ECI-D14Fx Network Dome Camera Quick Start Guide QSG VE D14Fx 041118NA 17
