DS-2CD2123G0D-IW2 Network Dome Camera Quick Start Guide C 0
Network Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT ©2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Dome Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Dome Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Dome Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Network Dome Camera·Quick Start Guide supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s).
Network Dome Camera·Quick Start Guide fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Network Dome Camera·Quick Start Guide Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Dome Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network Dome Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 2 Installation .................................................................................... 14 2.1 Camera Mounting ......................................................... 15 2.1.1 Wi-Fi Antenna Mounting .................................... 15 2.1.2 Ceiling Mounting ................................................ 15 2.1.
Network Dome Camera·Quick Start Guide 1 Appearance Description The overview of the camera is shown below.
Network Dome Camera·Quick Start Guide Table 1-1 Description No. Description 1 Bubble 2 Lens 3 IR LED 4 Wi-Fi Antenna 5 Black Liner 6 Safety Rope 7 Lens Adjusting Bracket 8 WPS (Wi-Fi Protected Setup)/Reset Button 9 Bottom Base 10 Mic 11 Power Interface 12 RJ45 Network Interface 13 Adapter Plate Note: ● Hold RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Dome Camera·Quick Start Guide Steps: 1) Press the WPS button on the router. 2) Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network. Note: The WPS button works as a reset button only when you press it when the camera is powering on. Press the WPS button on the camera, and then press the WPS button on the router will work as well, and the expire time of WPS connection on the camera is 120s.
Network Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC. Make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Dome Camera·Quick Start Guide 2.1 Camera Mounting 2.1.1 Wi-Fi Antenna Mounting Steps: 1. Screw up the Wi-Fi antenna as shown in the figure below. DC1 2 V I N Figure 2-1 Mount the Wi-Fi Antenna 2. Tighten the locking nut using the supplied wrench. 2.1.2 Ceiling Mounting Make sure the Wi-Fi antenna has been installed before the ceiling mounting. Steps: 1. Install the adapter plate to the ceiling with screws.
Network Dome Camera·Quick Start Guide Figure 2-2 Install the Adapter Plate to the Ceiling 2. If you need to route cables through the ceiling, cut a cable hole on the ceiling. Skip this step if you want to route the cables on the surface of the ceiling. 3. Route the cables of the camera. 4. Hold the bottom base and rotate the camera according to the marked direction on the adapter plate until it clicks into place.
Network Dome Camera·Quick Start Guide 5. Adjust the view angle. 1). Loosen the three base screws with the supplied wrench to remove the bubble. 2). Loosen the tilt adjusting screws. 3). Adjust the camera view angle in panning and tilting directions. The angle range of the pan direction is 0° to 355°, and the angle range of the tilt direction is 0° to 75°. 4). Tighten the tilt adjusting screws. 5). Tighten the base screws to replace the bubble.
Network Dome Camera·Quick Start Guide Steps: 1. Install the bracket to the ceiling with the self-tapping screws. Figure 2-5 Secure the Bracket 2. Secure the adapter to the bracket with screws. Figure 2-6 Secure the Adapter 3. If you need to route cables through the ceiling, cut a cable hole on the ceiling. Skip this step if you want to route the cables on the surface of the ceiling. 4. Route the cables of the camera. 5.
Network Dome Camera·Quick Start Guide Figure 2-7 Secure the Camera to the Adapter Plate 6. Adjust the view angle. For the detailed information, refer to step 6 in 2.1.2 Ceiling Mounting. 2.2 Installation of Network Cable Water-proof Jacket (Optional) Purpose: If the camera is installed outdoor, you can adapt the water-proof accessory for the network cable after the camera is secured on the installation surface.
Network Dome Camera·Quick Start Guide Table 2-1 Components No. Components 1 Camera’s Network Interface Socket 2 O-Type Gasket 3 Network Plug 4 Waterproof Endcap 5 Waterproof Rubber Gasket 6 Lock Nut 7 Network Cable from Router/Switch Steps: 1) Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (the rubber gasket inset ridge must face the waterproof endcap), and the waterproof endcap ④ in order.
Network Dome Camera·Quick Start Guide 5) Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. 6) Align the snap on the waterproof endcap ④ with the notch on the camera’s network interface socket ①, and then secure the waterproof endcap ④ to the camera’s network interface socket ① to finish installation. Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
Network Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: If the camera is used with a Wi-Fi NVR that can work as a wireless network router, the camera can connect to the NVR's Wi-Fi automatically after the camera is powered on. You can activate, add and configure the camera on the NVR. Make sure the NVR's Wi-Fi has been configured in advance. Refer to Quick Start Guide of Network Video Recorder for details.
Network Dome Camera·Quick Start Guide or or tw Ne e abl kC Ne tw 网络交换机 ork C abl e or Computer Network Camera 半球 Figure 3-2 Connecting via a Switch or a Router 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported.
Network Dome Camera·Quick Start Guide The default IP address of the camera is 192.168.1.64. The computer and the camera should belong to the same subnet. For the camera enables the DHCP by default, you need to use the SADP software to search the IP address. Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field.
Network Dome Camera·Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device.
Network Dome Camera·Quick Start Guide 3. Create and input the new password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Dome Camera·Quick Start Guide For IP address modification via client software, refer to the user manual of client software. Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Dome Camera·Quick Start Guide Figure 3-5 Modify the IP Address Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification.
Network Dome Camera·Quick Start Guide The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Dome Camera·Quick Start Guide The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6.
Network Dome Camera·Quick Start Guide For detailed instructions of further configuration, please refer to the User Manual of Network Camera.
Network Dome Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network Dome Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
Network Dome Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Dome Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching TM “Hik-Connect” in App Store or Google Play . 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1.
Network Dome Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Dome Camera·Quick Start Guide 5.4 Initializing the Memory Card Note: The memory card is only supported by certain models. See the actual device for details. Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD06205B 0
