Wi-Fi Kit DS-2CV1021G0-IDW1/NF Quick Start Guide 0
Wi-Fi Kit·Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Wi-Fi Kit·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Wi-Fi Kit·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Wi-Fi Kit·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Wi-Fi Kit·Quick Start Guide supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s).
Wi-Fi Kit·Quick Start Guide fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Wi-Fi Kit·Quick Start Guide Warnings For Network Camera: ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Wi-Fi Kit·Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100~240 VAC, 48 VDC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
Wi-Fi Kit·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Wi-Fi Kit·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Wi-Fi Kit·Quick Start Guide only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Power Supply Instructions for NVR Device: Use only power supplies listed in the user instructions. Standard Power Supply Models Manufacturer MSA-C2000IC 12.0-24P-DE MOSO POWER SUPPLY TECHNOLOGY CO.,LTD ADS-26FSG-1 2 12024EPG SHENZHEN HONOR ELECTRONIC CO.,LTD MSA-C2000IC 12.0-24P-GB MOSO POWER SUPPLY TECHNOLOGY CO.,LTD ADS-26FSG-1 2 12024EPB SHENZHEN HONOR ELECTRONIC CO.
Wi-Fi Kit·Quick Start Guide Table of Contents 1 Introduction .................................................................................. 13 1.1 Application .................................................................... 13 1.2 NVR Appearance ........................................................... 14 1.2.1 Front Panel ......................................................... 14 1.2.2 Rear Panel .......................................................... 15 1.3 Camera Appearance ..............
Wi-Fi Kit·Quick Start Guide 1 Introduction 1.1 Application The Wi-Fi kit includes four network cameras and a NVR device. The NVR works as a wireless network router, and the camera connects to the NVR's Wi-Fi automatically after the camera is powered on. Monitor Wi-Fi Camera VGA/HDMI NVR Note: If you want to access the NVR via Internet, connect your NVR with the router.
Wi-Fi Kit·Quick Start Guide 1.2 NVR Appearance 1.2.1 Front Panel Front Panel Description No. Icon Description 1 Indicator turns red when NVR is powered up. 2 Indicator lights in red when there is data transmission. 3 Indicator blinks blue when network connection is functioning properly.
Wi-Fi Kit·Quick Start Guide 1.2.2 Rear Panel Rear Panel Description No. Icon Description 1 Wi-Fi Antenna Wi-Fi antenna interface. 2 Power supply 12 VDC power supply. 3 Audio out One audio output. 4 VGA VGA interface 5 HDMI HDMI video output connector. 6 LAN One RJ-45 10M/100M self-adaptive Ethernet interface 7 Wi-Fi Antenna Wi-Fi antenna interface.
Wi-Fi Kit·Quick Start Guide No. Icon Description 8 USB Two USB 2.0 interface. 9 Ground Ground (needs to be connected when device starts up). 1.3 Camera Appearance 7 6 2 8 1 4 3 5 Overview Description No.
Wi-Fi Kit·Quick Start Guide No. Description Status Indicator ● Flashing Blue: Normal Wi-Fi connection. ● Solid Red: The camera is during startup. ● Flashing red and blue: The camera has started and starts Wi-Fi configuration. ● Flashing Red: 4 Fast Flashing: The network connection failed. Slow Flashing: Memory card error or other problems.
Wi-Fi Kit·Quick Start Guide 2 NVR Installation 2.1 Precautions During installation of the NVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables is no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the NVR is grounded. Environmental temperature should be within the range of -10 to +55º C, +14 to +131º F.
Wi-Fi Kit·Quick Start Guide Steps: 1. Remove the cover from device by unfastening the screws on panels. Remove Cover 2. Connect the data cable and power cable. a) Connect one end of data cable to the device motherboard. b) Connect the other end of data cable to HDD. c) Connect one end of power cable to HDD. d) Connect the other end of power cable to the device motherboard.
Wi-Fi Kit·Quick Start Guide Connect Cables 3. Set the device up, match HDD screw threads with the reserved holes on the device bottom, and fix HDD with screws. Fix HDD to Device Bottom 4. (Optional) Repeat the steps above to install other HDDs. 5. Reinstall the device cover and fasten screws.
Wi-Fi Kit·Quick Start Guide 3 Camera Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC. Make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Wi-Fi Kit·Quick Start Guide 3-Φ4 Φ55 Screw Hole Φ68 Φ18 Screw Hole Screw Hole template Side Outlet Drill the Holes 2. If you need to route cables through the wall or ceiling, cut a cable hole according to the drill template. Skip this step if you want to route the cables on the surface of the wall or ceiling. 3. Route the cables of the camera. 4. Install the camera to the wall or ceiling with screws.
Wi-Fi Kit·Quick Start Guide Install the Camera 5. Adjust the view angle of the camera. 1). Loosen the fixing ring to adjust the pan angle. 2). Loosen the adjusting screw 1 ring to adjust the tilt angle. 3). Loosen the adjusting screw 2 to adjust the rotation angle. 4). Tighten the fixing ring and the adjusting screws.
Wi-Fi Kit·Quick Start Guide 3.2 (Optional) Installation of Network Cable Waterproof Jacket Purpose: If the camera is installed outdoor, you can use the waterproof accessory for the network cable after the camera is secured on the installation surface. ① ② ③ ④ ⑤ ⑥ ⑦ Figure 3-4 Waterproof Accessory Components Components No.
Wi-Fi Kit·Quick Start Guide Steps: Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (the rubber gasket inset ridge must face the waterproof endcap), and the waterproof endcap ④ in order. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. Insert the network plug ③ into the camera’s network interface socket ①.
Wi-Fi Kit·Quick Start Guide Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
Wi-Fi Kit·Quick Start Guide 4 Menu Operation 4.1 Startup and Shutdown To start your NVR: Steps: 1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power button on the front panel should be red, indicating the device is receiving the power. 2. Press the power switch on the panel. The Power LED should turn blue. The unit will begin to start.
Wi-Fi Kit·Quick Start Guide For the first-time access, you need to activate the NVR by setting an admin password. No operation is allowed before activation. You can also activate the NVR via Web Browser, SADP or client software. 1. Input the same password in the text field of Create New Password and Confirm New Password.
Wi-Fi Kit·Quick Start Guide 4.4 Add IP Cameras 4.4.1 Wi-Fi Kit Cameras The supplied Wi-Fi kit cameras can connect to the NVR automatically after it is powered on. 4.4.2 Other Camers For the other cameras, follow the steps below to configure the Wi-Fi parameters and add the cameras. 1. Go to Menu > Configuration > WiFi. 2. Configure wireless network parameters, including Network Bridging, SSID, Security Mode, and Key. 3. Access the Web of the camera. 4.
Wi-Fi Kit·Quick Start Guide Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 4. Use a network cable to connect the NVR with a router. 5. In the Hik-Connect app, tap “+” on the upper-right corner and then scan the QR code of the NVR to add the NVR. 6. After the adding, you can get the live view, play back the videos in the app.
UD11327B 0
