Network Cube Camera Quick Start Guide 0
Network Cube Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Cube Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Cube Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Cube Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Cube Camera·Quick Start Guide supplier or to a designated collection point. For more information see:www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s).
Network Cube Camera·Quick Start Guide gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Network Cube Camera·Quick Start Guide Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Cube Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network Cube Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 1.1 Type I, II ......................................................................... 11 1.2 Type III .......................................................................... 14 2 Notice ........................................................................................... 18 3 Installation .............................................................
Network Cube Camera·Quick Start Guide 1 Appearance Description There are three types of appearances for 24 series camera. Please refer to the figure below. And one appearance will be taken as an example in the chapter below. 1.
Network Cube Camera·Quick Start Guide 1 4 7 2 3 5 6 8 11 12 13 14 9 10 15 Overview 12
Network Cube Camera·Quick Start Guide Description No.
Network Cube Camera·Quick Start Guide No. Description 13 O: Alarm Output Interface 14 Power supply interface (12 VDC) 15 Speaker 1.
Network Cube Camera·Quick Start Guide 1 2 3 4 6 7 8 9 10 Type III Overview Description No.
Network Cube Camera·Quick Start Guide No.
Network Cube Camera·Quick Start Guide A wireless router with the WPS function is required to enable the WPS function of the camera. Refer the steps below. Steps: Press the WPS button on the router. Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network. Note: The WPS button works as a reset button only when you press it when the camera is powering on.
Network Cube Camera·Quick Start Guide 2 Notice Do not install the camera in the extreme whether condition. Do not touch the lens with your finger. Do not install the camera towards the strong light or in the unstable lightening condition. Do not subject the camera to vibration, shock or heavy pressure.
Network Cube Camera·Quick Start Guide High humidity may damage the camera hardware; put it in dry and well-ventilated place. Under no circumstances should you submerge the camera in any type of liquid. Electromagnetic radiation may affect the video data transmission and the image quality. Do not install the camera near electromagnetic radiation source.
Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Cube Camera·Quick Start Guide 3.1.1 Type I, II Steps: 1. Insert the memory card into the card slot on the side of the camera. 2. (Optional) Push the inserted memory card to get it sprung out. Memory Card Install Memory Card 3.1.2 Type III Steps: 1. Remove the memory card slot cover. 2. Insert the memory card into the slot. 3. (Optional) Push the inserted memory card to get it sprung out. 4. Replace the slot cover.
Network Cube Camera·Quick Start Guide Slot Cover Install Memory Card 3.2 Type I, II Camera Mounting 3.2.1 Stand Mounting Steps: 1. Take the bracket out from the package.
Network Cube Camera·Quick Start Guide 2. Align the camera body to the bracket, and rotate the camera body to fix it with the bracket. Install the Camera Body 3. Assemble the camera as the steps above, and put the camera on the flat surface. 3.2.2 Ceiling Mounting 1. Drill the screw holes according to the drill template.
Network Cube Camera·Quick Start Guide Drill Template 1 1 Screw hole All:for Mounting Base Drill Template 2. Disassemble the 3-axis bracket. Hold the base with one hand, and rotate the pole anticlockwise to disassemble the pole from the base.
Network Cube Camera·Quick Start Guide 3. Install the fixed tray to the ceiling with the supplied screws. 4. Install the base to the fixed plate. Install the Fixed Plate and Mounting Base 5. Install the camera to the bracket. Install the Camera 6. Adjust surveillance angel 1). Loosen the knob to adjust the panning position and tilting position. 2). After adjusting the angle of the camera to the desired position, fasten the knob.
Network Cube Camera·Quick Start Guide Knob 360° 90° Figure 3-9 Adjust the Camera 3.3 Type III Camera Mounting This type of camera supports ceiling mounting and wall mounting. The following describes the steps for the wall or ceiling mounting. Steps: 1. Install the adapter plate to the wall or ceiling with the supplied screws.
Network Cube Camera·Quick Start Guide 2. Buckle the camera base into the adapter plate. Note: You are recommended to push into two buckles 1 and 2 first and then the third buckle 3. Then the camera can be fastened firmly on the base. 3 1 2 2 1 3 Figure 3-11 Buckle the Camera into Adapter Plate 3. Adjust surveillance angel. 1). Loosen the adjusting knob 1 to adjust the panning position and tilting position. 2). Loosen the adjusting knob 2 to adjust the rotation position. 3).
Network Cube Camera·Quick Start Guide Adjusting Knob 1 Adjusting Knob 2 Rotation: 0° to 360° Panning: 0° to 360° Tilting: 0° to 90° Figure 3-12 Adjust the Camera 28
Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. Wiring Connect the camera to network according to the following figures.
Network Cube Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software.
Network Cube Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Cube Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password. SADP Interface Note: The SADP software supports activating the camera in batch.
Network Cube Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Cube Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
Network Cube Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 6.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Cube Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Cube Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Cube Camera·Quick Start Guide 6 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 6.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser.
Network Cube Camera·Quick Start Guide Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 4.2.
Network Cube Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 5. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera.
Network Cube Camera·Quick Start Guide 6.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 6.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 6.1. Steps: 1.
Network Cube Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 6-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network Cube Camera·Quick Start Guide 6.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD07738B-B 0