iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Legal Information © 2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Symbol Danger Caution Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important points of the main text.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Environment • Make sure the running environment meets the requirement of the device. The operating temperature shall be -30° to 60° C (-22° to 140° F), and the operating humidity shall be 95% or less, non-condensing. • When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out. • Do not expose the device to high electromagnetic radiation or dusty environments.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Contents Symbol Conventions.......................................................................................................................................... 2 Safety Instruction ............................................................................................................................................. 3 Contents .....................................................................................................................
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Audio Output .................................................................................................................................. 25 Environmental Noise Filter ............................................................................................................ 25 Two-Way Audio ...........................................................................................................................................
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Draw Area ....................................................................................................................................... 52 Set Size Filter ................................................................................................................................. 52 Chapter 7 Network Settings ............................................................................................................................
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Synchronize Time Manually ........................................................................................................... 75 Set NTP Server ................................................................................................................................ 75 Synchronize Time by Satellite ....................................................................................................... 75 Set DST .............................
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual View Face Counting Result ........................................................................................................... 94 Queue Management .................................................................................................................................... 94 Set Regional People Queuing-Up.................................................................................................. 95 Set Waiting Time Detection .........
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 1 System Requirements Your computer should meet the requirements for proper visiting and operating the product. • Operating System: Microsoft Windows XP SP1 and above version • CPU: 2.0 GHz or higher • RAM: 1 GB or more • Display: 1024×768 resolution or higher • Web Browser: Internet Explorer 8.0 or above version, Mozilla Firefox 30.0 to 51, or Google Chrome 31 to 51.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 2 Device Activation and Accessing To protect the security and privacy of the user account and data, you should set a login password to activate the device when access the device via network. See the software client user manual for details about the client software activation. Activate the Device via SADP Search and activate the online devices via SADP software. Before You Start Access www.hikvision.com to get SADP software to install. Steps 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 3. Input 192.168.1.64 in the browser. 4. Set device activation password. STRONG PASSWORD RECOMMENDED − We highly recommend that you create a strong password of your own choosing (using a minimum of eight characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. We also recommend that you reset your password regularly.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Admin Password Recovery If you forget the admin password, you can reset the password by clicking Forget Password on the login page after completing the account security settings. You can reset the password by setting the security question or e-mail. When you need to reset the password, make sure that the device and the PC are on the same network segment.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 3 Live View Introduction to live view parameters, function icons, and transmission parameters settings. Live View Parameters The supported functions vary by model. Enable and Disable Live View This function is used to quickly enable or disable live view of all channels. • Click to start live view of all channels. • Click to stop live view of all channels. Adjust Aspect Ratio Steps 1. Click Live View. 2. Click to select the aspect ratio.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Window Division • : 1 × 1 window division • : 2 × 2 window division • : 3 × 3 window division • : 4 × 4 window division Light Click to turn on or turn off the illuminator. Count Pixel Use to get the height and width pixel of the selected region in the live view image. Steps 1. Click to enable the function. 2. Drag the mouse on the image to select a desired rectangle area.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Lens initialization is used on devices equipped with a motorized lens. The function can reset the lens when long time zoom or focus results in blurred image. This function varies by model. • Manual Lens Initialization: Click • Auto Lens Initialization: Go to Configuration → System → Maintenance → Lens Correction to enable this function.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual When the image is too dark, click When the image is too bright, click to enlarge the iris. to stop down the iris. Conduct 3D Positioning 3D positioning relocates the selected area to the image center. Steps 1. Click to enable the function. 2. Select a target area in live image. • Left click on a point on live image: the point is relocated to the center of the live image with no zooming in or out effect.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual HTTP is suitable for situations in which a third-party needs to get the stream from the device. • Play Performance Shortest Delay The device takes the real-time video image as the priority over the video fluency. Balanced The device ensures both the real-time video image and the fluency. Fluent The device takes the video fluency as the priority over real-time.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Error Correction: The resolution and bitrate stay the same as the set values on Video page. The mode is used to correct the data error during transmission to ensure the image quality. You can set the Error Correction Proportion within range of 0–100. When the proportion is 0, the data error will be corrected by data retransmission.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 4 Video and Audio This part introduces the configuration of video and audio related parameters. Video Settings This section introduces video parameter settings such as stream type, video encoding, and resolution. 1. Go to setting page: Configuration → Video/Audio → Video. Stream Type For devices that support more than one stream, you can specify parameters for each stream type.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Video: Only video content is contained in the stream. • Video & Audio: Video content and audio content are contained in the composite stream. Resolution Select video resolution according to actual needs. Higher resolution requires more bandwidth and storage. Bitrate Type and Max. Bitrate • Constant Bitrate: The stream is compressed and transmitted at a comparatively fixed bitrate. The compression speed is fast, but mosaic may occur on the image.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • H.265+: H.265+ is an improved compression coding technology based on H.265. By enabling H.265+, you can estimate the HDD consumption by its maximum average bitrate. Compared to H.265, H.265+ reduces storage by up to 50% with the same maximum bitrate in most scenes. When H.265+ is enabled, Max. Average Bitrate is configurable. The device gives a recommended max. average bitrate by default.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set ROI ROI (Region of Interest) encoding helps to assigns more encoding resource to the region of interest, thus to increase the quality of the ROI whereas the background information is less focused. Before You Start Please check the video coding type. ROI is supported when the video coding type is H.264 or H.265. Steps 1. Go to Configuration → Video/Audio → ROI. 2. Check Enable. 3. Select Stream Type. 4. Select Region No.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set Target Tracking ROI The moving target is clearer than other areas in live image or recordings after enabling the function. Before You Start Go to Configuration → PTZ → Smart Tracking to complete the smart tracking settings. Steps 1. Go to Configuration → Video/Audio → ROI. 2. Check Enable Target Tracking. 3. Set ROI Level for target tracking. The higher the value, the clearer the target. 4. Click Save.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Audio Settings This function sets audio parameters such as audio encoding and environment noise filtering. Go to the audio settings page: Configuration → Video/Audio → Audio. Audio Encoding Select the audio encoding compression of the audio. Audio Input Connect the audio input device as required. The audio input display varies by model.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4. Click , disable the two-way audio function. Display Settings This offers the parameter settings to adjust image features. Go to Configuration → Image → Display Settings. Click Default to restore settings. Scene Mode There are several sets of image parameters predefined for different installation environments. Select a scene according to the actual installation environment to speed up the display settings.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Day/Night Switch Day/Night Switch function can provide color images in te day mode and black/white images in night mode. Switch mode is configurable. Day: The image is always in color. Night: The image is always black/white. Auto: The camera automatically switches between day mode and the night mode according to the illumination. • Scheduled-Switch: Set the Start Time and the End Time to define the duration for day mode.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • DNR: Digital Noise Reduction is used to reduce the image noise and improve the image quality. Normal and Expert modes are selectable. Normal: Set the DNR level to control the noise reduction. Use a higher level for more reduction. Expert: Set the DNR level for both space DNR and time DNR to control the noise reduction degree. A higher level means stronger reduction degree.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual OSD You can customize OSD (On-screen Display) information such as device name, time/date, font, color, and text overlay displayed on video stream. Go to OSD setting page: Configuration → Image → OSD Settings. Set the corresponding parameters, and click Save to take effect. • Character Set: Select character set for displayed information. If Korean is required to displayed on screen, select EUC-KR. Otherwise, select GBK.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to picture overlay setting page: Configuration → Image → Picture Overlay. 2. Click Browse to select a picture, and click Upload. The picture with a red rectangle will appear in live view after successfully uploading. 3. Check Enable Picture Overlay. 4. Drag the picture to adjust its position. 5. Click Save.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 5 Video Recording and Picture Capture This section introduces capturing video clips and snapshots, playback, and downloading captured files. Storage Settings This part introduces the configuration of several common storage paths. Set Memory Card To store files to memory card, make sure you insert and format the memory card in advance. Before You Start Insert the memory card to the camera.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 3. Click R/W Lock to set the reading and writing authority of the memory card. 1) Add a LockSelect the Lock Switch as ON. 2) Enter the password. 3) Click Save. Unlock • If you use the memory card on the camera that locks it, unlocking will be done automatically and no unlocking procedures are required on the part of users.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • User Name and Password: The FTP user should have the permission to upload pictures. If the FTP server supports picture uploading by anonymous users, you can check Anonymous to hide your device information during uploading. • Directory Structure: The saving path of snapshots in the FTP server. • Picture Filing Interval: For better picture management, you can set the picture filing interval from 1 day to 30 days.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Click Save. eMMC Protection If you enable eMMC protection, the lifespan of the eMMC is displayed. Set Cloud Storage It helps to upload the captured pictures and data to the cloud. The platform requests picture directly from the cloud for picture and analysis. The function is supported only by certain models. Steps CAUTION! If cloud storage is enabled, the pictures are preferentially stored in the cloud storage server. 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to Configuration → Storage → Schedule Settings → Record Schedule. 2. Check Enable. 3. Select a record type. The record types vary by model. • Continuous: The video will be recorded continuously according to the schedule. • Motion: When motion detection is enabled and trigger recording is selected as linkage method, object movement is recorded.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Set the Record File Size and saving path to for recorded files. 3. Click Save. 4. Click to start recording. Click to stop recording. Set Lite Storage After lite storage is enabled, the video stream frame rate and bitrate can be reduced to lengthen the storage time of the memory card when there is no moving object in the monitoring scenario. Steps 1. Go to Configuration → Storage → Storage Management → Lite Storage. 2.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2) Select the video files and then click Download. Go to Configuration → Local, click Save downloaded files to to change the saving path of downloaded video files. Capture Configuration The device can capture the pictures manually or automatically and save them in configured saving path. You can view and download the snapshots. Capture Automatically This function can capture pictures automatically during configured time periods.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual View and Download Pictures You can search, view, and download the pictures stored in the local storage or network storage. Steps 1. Click Picture. 2. Set search condition and click Search. Matching pictures show in the file list. 3. Select the pictures then click Download to download them. Go to Configuration → Local, click Save snapshots when playback to change the saving path of pictures.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 6 Events and Alarms This section introduces configuring events. The device takes certain responses to triggered alarms. Basic Event Set Motion Detection Motion detection detects moving objects in the detection region and triggers linked actions. Steps 1. Go to Configuration → Event → Basic Event → Motion Detection. 2. Check Enable Motion Detection. 3. Optional: Highlight to display the moving object in the image in green.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual It switches to day mode during the set periods and switches to night mode during the other periods. • Sensitivity: The higher the sensitivity value, the more sensitive the motion detection. If the sensitivity is set to 0, motion detection and dynamic analysis do not take effect. • Proportion: The proportion that a moving object occupies in the drawn area. When the size of the object exceeds the set proportion, motion detection is triggered. 3.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Figure 6-2 Set Rules 4. Optional: You can set the parameters of multiple areas by repeating the above steps. Set Video Tampering Alarm When the configured area is covered and cannot be monitored normally, the alarm is triggered and the device takes certain alarm response actions. Steps 1. Go to Configuration → Event → Basic Event → Video Tampering. 2. Check Enable. 3. Set the Sensitivity. The higher the value is, the easier to detect the area covering.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Figure 6-3 Set Video Tampering Area 5. Refer to Set Arming Schedule for setting scheduled time. Refer to Linkage Method Settings for setting linkage method. 6. Click Save. Set PIR Alarm A PIR (Passive Infrared) alarm is triggered when an intruder moves within the detector’s field of view. The heat energy dissipated by a person or any other warm blooded creature such as a dog, cat, etc. can be detected. Steps Only certain models support PIR alarm. 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 1. Go to Configuration → Event → Basic Event → Exception. 2. Select Exception Type. • HDD Full: The HDD storage is full. • HDD Error: Error occurred in HDD. • Network Disconnected: The device is offline. • IP Address Conflicted: The current device’s IP address is same as that of another device in the network. • Illegal Login: Incorrect user name or password entered. 3. Refer to Linkage Method Settings for setting linkage method. 4. Click Save.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to Configuration → Event → Basic Event → Video Quality Diagnosis. 2. Select Diagnosis Type. 3. Set the corresponding parameters. • Alarm Detection Interval: The time interval to detect the exception. • Sensitivity: The higher the value is, the more easily the exception will be detected, and the higher possibility of misinformation would be. • Alarm Delay Times: The device uploads the alarm when the alarm reaches the set number of times. 4.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Detect Audio Exception Audio exception detection function detects the abnormal sound in the surveillance scene such as the sudden increase/decrease of the sound intensity, and certain actions can be taken in response. Steps 1. Go to Configuration → Event → Smart Event → Audio Exception Detection. 2. Select one or several audio exception detection types. • Audio Loss Detection: Detect sudden loss of audio track.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Detect Scene Change This detects change of the surveillance scene. Certain actions can be taken when the alarm is triggered. Steps 1. Go to Configuration → Event → Smart Event → Scene Change Detection. 2. Click Enable. 3. Set the Sensitivity. The higher the value, the more easily the change of scene can be detected. But detection accuracy is reduced. 4. Refer to Set Arming Schedule for setting scheduled time.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 3. See Set Arming Schedule for setting scheduled time. See Linkage Method Settings for setting linkage method. 4. Click Save. Set Intrusion Detection Detects objects entering and loitering in a pre-defined virtual region, after which the device can take linkage actions. Steps 1. Go to Configuration → Event → Smart Event → Intrusion Detection. 2. Check Enable. 3. Select a Region. For the detection region settings, refer to Draw Area. 4. Set rules.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set Line Crossing Detection Detects objects crossing a pre-defined virtual line. If it occurs, the device can take linkage actions. Steps 1. Go to Configuration → Event → Smart Event → Line Crossing Detection. 2. Check Enable. 3. Select one Line and set the size filter. For the size filter settings, refer to Set Size Filter. 4. Click Draw Area and a line with an arrow appears in the live video. Drag the line to the location on the live video as desired.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 8. Click Save. Set Region Entrance Detection Use to detect objects entering a pre-defined virtual region. If it occurs, the device can take linkage actions. Steps 1. Go to Configuration → Event → Smart Event → Region Entrance Detection. 2. Check Enable. 3. Select one Region. For the region settings, refer to Draw Area. 4. Select the detection target. Human and Vehicle are available.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4. Select the detection target. Human and Vehicle are available. If the detection target is not selected, all detected targets will be reported, including humans and vehicles. Figure 6-7 Set Rule 5. Optional: You can set the parameters of multiple areas by repeating the above steps. 6. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 7. Click Save.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Figure 6-8 Set Rule 5. Optional: You can set the parameters of multiple areas by repeating the above steps. 6. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 7. Click Save. Set Object Removal Detection Detects whether objects are removed from a pre-defined detection region such as exhibits on display.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Figure 6-9 Set Rule 5. Optional: Repeat the above steps to set more regions. 6. For the arming schedule settings, see Set Arming Schedule. For the linkage method settings, see Linkage Method Settings. 7. Click Save. The function is supported only by certain models. The actual display varies by model. Draw Area This section introduces the configuration of area. Steps 1. Click Draw Area. 2.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 7 Network Settings TCP/IP TCP/IP settings must be properly configured before you operate the device over a network. IPv4 and IPv6 are both supported. Both versions can be configured simultaneously without conflicting with each other. 1. Go to Configuration → Basic Configuration → Network → TCP/IP for parameter settings. • NIC Type: Select a NIC (Network Interface Card) type according to your network. • IPv4: Two IPv4 modes are available.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • IP Address: Address of multicast host • Stream Type: Stream type of the multicast source • Video Port: Video port of the selected stream • Audio Port: Audio port of the selected stream • FEC Port: FEC port of the selected stream • FEC Ratio: Ratio of forward error correction Multicast Discovery Check the Enable Multicast Discovery, and then the online network camera can be automatically detected by client software via private multicast protocol in the
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Select Server Certificate. 3. Select Encrypted Algorithm. 4. Click Save. Only certain device models support this function. If the function is abnormal, check if the selected certificate is abnormal in certificate management. Port Mapping By setting port mapping, you can access devices through the specified port.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual What To Do Next Go to the router port mapping settings interface and set the port number and IP address to be the same as those on the device. For more information, see the router user manual. Set Port Mapping on Router The following settings are for a specific router. Settings vary by router. Steps 1. Select the WAN Connection Type. 2. Set the IP Address, Subnet Mask and other network parameters of the router. 3.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • HTTP Port: Port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.168.1.64:81 in the browser for login. • HTTPS Port: Port through which the browser accesses the device with certificate. Certificate verification is required to ensure secure access. • RTSP Port: Real-time streaming protocol port. • SRTP Port: Secure real-time transport protocol port.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • By Browser: Enter the domain name in the browser address bar to access the device. • By Client Software: Add domain name to the client software. Refer to the client manual for specific adding methods. Access to Device via PPPoE Dial Up Connection This device supports the PPPoE auto dial-up function. The device gets a public IP address by ADSL dial-up after the device is connected to a modem. You need to configure the PPPoE parameters of the device.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set Wireless Dial The built-in wireless module offers dial-up access to the Internet for the device. Before You Start Get a SIM card, and activate 3G/4G services. Insert the SIM card into the corresponding slot. Steps 1. Go to Configuration → Network → Advanced Settings → Wireless Dial. 2. Check to enable the function. 3. Click Dial Parameters to configure and save the parameters. 4. Click Dial Plan. See Set Arming Schedule for detailed information. 5.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4) Click Save. 5) Optional: Repeat the steps above to set multiple recipients. • : Modify the white list parameters. • : Delete the white list that already set. • Send Test SMS: Send a message to the mobile phone for test. 4. Click Save. Wi-Fi Connect the device to a wireless network by setting Wi-Fi parameters. This function is supported only by certain device models.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Use PBC Set PBC to connect Wi-Fi automatically. PBC refers to Push-Button-Configuration, in which the user simply has to push a button, either an actual or virtual one (as the Connect button on the configuration interface of the IE browser), on both the Access Point (and a registrar of the network) and the new wireless client device. Before You Start The operation should be done within 120 seconds, otherwise the connection will fail. Steps 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Use PIN on Device The device can automatically connect the network by setting the device PIN code parameters in wireless router or AP via WPS or QSS protocols. Steps 1. Go to TCP/IP settings page: Configuration → Network → Basic Configuration → TCP/IP. 2. Select Wlan to set the parameters. Refer to TCP/IP for detailed configuration. For stable use of Wi-Fi, it is not recommended to use DHCP. 3.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4) Click Connect. 5. Click Save. 6. Go to TCP/IP setting page: Configuration → Network → Basic Configuration → TCP/IP, and click Wlan to check the IPv4 Address and log in the device. • Input the IP address in the browser to access the device. • Add the device in client application. Select IP/Domain, and input IP address and other parameters to access the device. Set Network Service You can control the ON/OFF status of certain protocols as desired.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to Configuration → Network → Advanced Settings → Integration Protocol. 2. Check Enable ONVIF. 3. Click Add to configure the ONVIF user. • Delete: Delete the selected ONVIF user. • Modify: Modify the selected ONVIF user. 4. Click Save. 5. Optional: Repeat the steps above to add more ONVIF users. Set Alarm Server The device can send alarms to destination IP address or host name through HTTP, HTTPS, or ISUP protocol.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Scan the QR code below to download the application. If errors such as “Unknown app” occur during the installation, solve the problem in two ways. Visit https://appstore.hikvision.com/static/help/index.html to refer to the troubleshooting. Visit https://appstore.hikvision.com/, and click Installation Help at the upper right corner of the interface to refer to the troubleshooting. 2. Start the application and register for a Hik-Connect user account. 3.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 6. Create a verification code or change the old verification code for the camera. The verification code is required when you add the camera to Hik-Connect service. 7. Save the settings. Enable Hik-Connect Service via SADP Software This part introduce how to enable Hik-Connect service via SADP software of an activated camera. Steps 1. Run SADP software. 2. Select a camera and enter Modify Network Parameters page. 3. Check Enable Hik-Connect. 4.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Start the application and register for a Hik-Connect user account. 3. Log in after registration. Add Camera to Hik-Connect Steps 1. Connect your mobile device to a Wi-Fi. 2. Log into the Hik-Connect app. 3. In the home page, tap “+” on the upper-right corner to add a camera. 4. Scan the QR code on camera body or on the Quick Start Guide cover.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 8 Arming Schedule and Alarm Linkage Arming schedule is a customized time period in which the device performs certain tasks. Alarm linkage is the response to the detected certain incident or target during the scheduled time. Set Arming Schedule Set the valid time of the device tasks. Steps 1. Click Arming Schedule. 2. Drag the time bar to draw desired valid time. Up to eight periods can be configured for one day. 3. Adjust the time period.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Set the manual alarm parameters. • Alarm Output No.: Select the alarm output no. according to the alarm interface connected to the external alarm device. • Alarm Name: Custom a name for the alarm output. • Delay: Select Manual. 2. Click Manual Alarm to enable manual alarm output. 3. Optional: Click Clear Alarm to disable manual alarm output.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set E-mail When the e-mail is configured and Send Email is enabled as a linkage method, the device sends an e-mail notification to all designated receivers if an alarm event is detected. Before You Start Set the DNS server before using the E-mail function. Go to Configuration → Network → Basic Settings → TCP/IP for DNS settings. Steps 1. Go to e-mail settings page: Configuration → Network → Advanced Settings → Email. 2. Set e-mail parameters.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Flashing Light After enabling Flashing Light and setting the Flashing Light Alarm Output, the light flashes when an alarm event is detected. Set Flashing Alarm Light Output When events occur, the flashing light on the device can be triggered as an alarm. Steps 1. Go to Configuration → Event → Basic Event → Flashing Alarm Light Output. 2. Set Flashing Duration, Flashing Frequency, and Brightness.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 3. Optional: Click Test to play the selected audio file on the device. 4. Set arming schedule for audible alarm. See Set Arming Schedule for details. 5. Click Save. The function is supported only by certain device models.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 9 System and Security This section is an introduction to system maintenance, system settings, and security management, and explains how to configure relevant parameters. View Device Information You can view device information, such as Device No., Model, Serial No., and Firmware Version. Enter Configuration → System → System Settings → Basic Information to view the device information.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Restore and Default Restore and Default helps restore the device parameters to the default settings. Steps 1. Go to Configuration → System → Maintenance → Upgrade & Maintenance. 2. Click Restore or Default according to your needs. • Restore: Reset device parameters, except user information, IP parameters, and video format to the default settings. • Default: Reset all the parameters to the factory default. Be careful when using this function.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Synchronize Time Manually Steps 1. Go to Configuration → System → System Settings → Time Settings. 2. Select Time Zone. 3. Click Manual Time Sync.. 4. Choose one time synchronization method. • Select Set Time, and manually input or select date and time from the pop-up calendar. • Check Sync. with computer time to synchronize the time of the device with that of the local PC. 5. Click Save.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4. Click Save. Set DST If the region where the device is located adopts Daylight Saving Time (DST), you can set this function. Steps 1. Go to Configuration → System → System Settings → DST. 2. Check Enable DST. 3. Select Start Time, End Time and DST Bias. 4. Click Save. Set RS-485 RS-485 is used to connect the device to an external device.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual External Device For devices that support external devices, including the supplement light, wiper on the housing, and the LED light, you can control them via the Web browser when it is used with the housing. External devices vary by model. • Brightness: Adjust Low Beam Brightness and High Beam Brightness according to the actual scene. • Timing: The LED light will be turned on by the schedule you set. You should set Start Time and End Time.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual the device or enable live view because of compatibility. An encrypted algorithm with high strength is recommended. • WEB Authentication: Digest and digest/basic are supported, which means authentication information is needed when a Web request is sent to the device. If you select digest/basic, it means the device supports digest or basic authentication. If you select digest, the device supports only digest authentication.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Check Enable to access the camera via HTTP or HTTPS protocol. 3. Check Enable HTTPS Browsing to access the camera only via HTTPS protocol. 4. Select the Server Certificate. 5. Click Save. If the function is abnormal, check if the selected certificate is abnormal in Certificate Management. Set QoS QoS (Quality of Service) can help improve the network delay and network congestion by setting the priority of data sending.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 1. Go to Configuration → System → Security → Advanced Security to complete settings. Search Security Audit Logs You can search and analyze the security log files of the device so as to find out illegal intrusions and troubleshoot security events. Steps This function is supported only by certain camera models. 1. Go to Configuration → System → Maintenance → Security Audit Log. 2. Select log types, Start Time, and End Time. 3. Click Search.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Create Certificate Request Before You Start Select a self-signed certificate. Steps 1. Click Create Certificate Request. 2. Enter the related information. 3. Click OK. Import Certificate Steps 1. Click Import. 2. Click Create Certificate Request. 3. Enter the Certificate ID. 4. Click Browser to select the desired server/client certificate. 5. Select the desired import method and enter the required information. 6. Click OK. 7.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Create Certificate Request: Refer to Create Certificate Request • Import Certificate: Refer to Import Certificate Install CA Certificate Steps 1. Click Import. 2. Enter the Certificate ID. 3. Click Browser to select the desired server/client certificate. 4. Select the desired import method and enter the required information. 5. Click OK. Up to 16 certificates are allowed. Enable Certificate Expiration Alarm Steps 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to Configuration → System → User Management → User Management. 2. Click Add. Enter User Name, select Level, and enter Password. Assign remote permission to users based on needs. • Administrator: The administrator has the authority for all operations and can add users and operators and assign permission.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 10 Allocate VCA Resource VCA resource offers options to enable certain VCA functions according to actual needs. It helps allocate more resources to the desired functions. Steps 1. Go to Configuration → System → System Settings → VCA Resource. 2. Select desired VCA function. 3. Save the settings. Some VCA functions are mutually exclusive. When certain function or functions are selected and saved, others will not be hidden.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Figure 10-1 Set Face Capture The device will detect if there is a human face in the area by the set minimum pupil distance. 6. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 7. Click Save. 8. For overlay and capture settings, refer to Overlay and Capture. For advanced parameters settings, refer to Face Capture Algorithms Parameters.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Text Overlay: You can check desired items and adjust their order to display on captured pictures by . The content of Device No. and Camera Info should be on the same page. Face Capture Algorithms Parameters Use to set and optimize the parameters of the algorithm library for face capture. 1. Go to Configuration → Face Capture → Advanced Configuration → Parameters. • Face Capture Version: It lists the version of the algorithms library.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Face Filtering Time: Time interval between the camera detecting a face and taking a capture action. If the detected face stays in the scene for less than the set filtering time, capture will not be triggered. For example, if the face filtering time is set as 5 seconds, the camera will capture the detected face if the face stays in the scene for 5 seconds.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 5. Click and drag the lane line to set its position, or click and drag the line end to adjust the length and angle of the line. 6. Adjust the zoom ratio of the camera so that the size of the vehicle in the image is close to that of the red frame. Only the position of red frame is adjustable. Only one license plate can be captured at a time for each lane. 7. Select Region and Country/Region. 8. Select the license plate information upload mode.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2. Select Mixed-Traffic Detection as detection type. 3. Check Enable. 4. Select the lane number. 5. Select Region and Country/Region. 6. Set arming schedule and linkage method. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 7. Click Save. Uploading Pictures Settings You can set the image parameters of the captured images in vehicle detection and mixed-traffic detection.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4. Click Export to open the PC local directory. 5. Select a directory in your PC local directory. 6. Name the file in the file name text filed. 7. Click Save. Multi-Target-Type Detection Multi-Target-Type Detection is to detect, capture, and upload data of targets of multiple types such as human face, human body, and vehicle. Certain models require enabling Multi-Target-Type Detection on VCA Resource page first.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Display Target info. on Alarm Picture: Overlay the alarm picture with target information. • Target Picture Settings: Custom, Head Shot, Half-Body Shot, and Full-Body Shot are selectable. If you select Custom, you can customize width, head height, and body height as required. You can check Fixed Value to set the picture height.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual level. If a face in the actual scene is darker than the set reference, the device increases the exposure level. Minimum Duration: The extra time the device keeps the face exposure level after the face disappears in the scene. Face Filtering Time: Time interval between the camera detecting a face and taking a capture action. If the detected face stays in the scene for less than the set filtering time, capture will not be triggered.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Max. Pupil Distance: The max. pupil distance refers to the maximum square size composed by the area between two pupils, and it is the basic standard for a camera to identify a target. 5. Click to draw the detection area. Draw an area by left-clicking end-points in the live view window, and right-clicking to finish the area drawing. 6. Click to draw the detection line. The arrow shows entering direction, you can click direction.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Face Counting Algorithm Parameters It is used to set and optimize the parameters of the algorithm parameters for Face Counting. These functions vary according to different models. • Face Capture Mode: Current algorithm version, which cannot be edited. • Best Shot: The best shot after the target leaves the detection area. • Capture Times: Capture times a face will be captured during its stay in the configured area. The default value is 1.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set Regional People Queuing-Up Use to count queuing-up persons in defined regions. Alarms are triggered when the alarm threshold condition and the alarm trigger are both met. Before You Start To enable the function, go to VCA Resource, and select Queue Management. Steps 1. Go to Configuration → Queue Management. 2. Select Regional People Queuing-Up. 3. Click Add Region to draw the detection area and set Region Name and Alarm Interval.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Steps 1. Go to Configuration → Queue Management. 2. Select Waiting Time Detection. 3. Click Add Region to draw the detection area and set Region Name, and Alarm Interval. Repeat this step above to set more areas. • Alarm Interval: During the set alarm interval, alarms of the same type trigger only one notification Figure 10-3 Set Waiting Time Detection 4. Set Alarm threshold. An alarm is triggered when the alarm threshold condition is met. 5.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual • Select Queue Status Analysis and Multi-Level Comparison to compare the time and duration of the queue at different queue length levels. Steps With an on-board memory card installed, the device can save up to one month’s data. With no memory card installed, the device can save only up to one week’s data. 1. Select the analysis mode. • Queuing-Up Time Analysis: Queuing-Up time analysis calculates people number of different waiting time levels.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 4. Set the detection line and the objects across the line will be detected and counted. • : Draw a detection line. • : Delete the detection line. • : Change the direction. Figure 10-4 Set Counting 5. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 6. Click Save. View Counting Statistics You can view and export the counting statistics stored in device or memory card.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Only certain device models support the function. Set Hard Hat Detection Before You Start 1. Go to Configuration → System → System Settings → VCA Resources to enable Hard Hat Detection. Steps 1. Go to Configuration → Hard Hat Detection, and check Enable Hard Hat Detection. 2. Optional: Set Target Generation Speed. It refers to the target generation speed of the face entering the detection region. The greater the value, the quicker the generation speed. 3.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 2) Input library name, threshold and remarks. • Threshold: Face similarity higher than set threshold triggers face picture comparison alarm uploading. 3) Click OK. 4) Optional: Modify face picture library. Select library, click , and change related parameters. 5) Optional: Delete a library. Select the desired library and click . 3. Add face pictures to the library. The picture format should be JPEG and the size no larger than 300 KB per file.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Set Face Picture Comparison The function compares captured pictures with face pictures in library and outputs comparison result. Comparison result can trigger certain actions when arming schedule and linkage method are set. Before You Start You should first create a face picture library and add face pictures. See Set Face Picture Library. Steps 1. Go to Configuration → Comparison and Modeling → Face Comparison and Modeling. 2.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Face Modeling Face modeling serves the purpose of collecting face pictures, creating face models, and uploading data to the surveillance center. Before You Start Face Capture or Multi-Target-Type detection should be configured for face picture collection. See Face Capture or Multi-Target-Type Detection for configuration instructions. Steps 1. Go to Configuration → Comparison and Modeling → Face Comparison and Modeling. 2. Select Face Modeling to start.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 11 Open Platform Open platform allows you to install a third-party application to develop and run its functions and services. Only certain device models support this function. Set Open Platform 1. Go to Configuration → Open Platform. Before installing the application, read the Disclaimer at the bottom and make sure that the application you want to install fits the following conditions. Each application has its own exclusive name.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 12 Set EPTZ EPTZ (Electronic PTZ) is a high-resolution function that digitally zooms and pans into portions of the image, with no physical camera movement. Before You Start If you want to use the EPTZ function, make sure you have select the Fourth Stream in the live view. Fourth stream and EPTZ must both be enabled simultaneously. Steps 1. Go to Configuration → EPTZ. 2. Check Enable EPTZ. 3. Check Fourth Stream. 4. Select the Application.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Chapter 13 Smart Display Displays captured pictures when enabling smart functions. Layout Preview Click and select Layout Preview. Select the contents according to your needs. When you select real-time analysis, you can select the contents only for real-time analysis. Detection Attribute Click and select Detection Attribute.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Appendix A: Device Command Scan the following QR code to get device common serial port commands. Note that the command list contains the commonly used serial port commands for all Hikvision network cameras.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Appendix B: Device Communication Matrix Scan the following QR code to get device communication matrix. Note that the matrix contains all communication ports of Hikvision network cameras.
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual UM iDS-2CD7xxG0-xxxxx 021021NA 108
